...
- Centralized authorization via RADIUS server (802.1X WPA/WPA2/WPA3 Enterprise);
- WPA/WPA2/WPA3 data encryption;
- Support for Captive Portal;
- Support for WIDS/WIPS1.
| Подсказка | ||||||
|---|---|---|---|---|---|---|
|
...
WAN Ethernet interface parameters | |
|---|---|
Number of ports | 1 |
Electrical connector | RJ-45 |
Data rate | 100/1000/2500 Mbps, auto-negotiation |
Standards | BASE-T |
Wireless interface parameters | |
Standards | 802.11a/b/g/n/ac/ax |
Frequency range | 2400–2483.5 MHz; 5150–5350 MHz, 5470–5850 MHz |
Modulation | BPSK, QPSK, 16QAM, 64QAM, 256QAM, 1024QAM |
Operating channels | 802.11b/g/n/ax: 1–13 (2402–2482 MHz) 802.11a/n/ac/ax:
|
Speed of data transmission | 2.4 GHz, 802.11ax: 574 Mbps |
| Maximum number of concurrent sessions | 2.4 GHz: 512 5 GHz: 512 |
Maximum transmitter power | 2.4 GHz: 22.5 dBm |
Antenna gain | 2.4 GHz: ~ 3 dBi |
Receiver sensitivity | 2.4 GHz: up to -92 dBm |
Security | Centralized authorization via RADIUS server (802.1X WPA/WPA2/WPA3 Enterprise) |
Support for OFDMA and MU-MIMO 2×2 | |
Control | |
Remote control | Web interface, Telnet, SSH, CLI, NETCONF, SoftWLC |
Access restriction | By password |
General parameters | |
Flash memory | 256 MB NAND Flash |
RAM | 1 GB DDR4 RAM |
Power supply | PoE+ 48 V/56 V (IEEE 802.3at-2009) |
Power consumption | No more than 13 W |
Range of operation temperatures | From +5 to +40 °C |
Relative humidity at 25 °C | Up to 80 % |
Dimensions (Diameter x Height) | 230 × 56 mm |
Weight | 0.56 kg |
Lifetime | No less than 15 years |
...
- Connect cables to the corresponding connectors of the device. Description of the connectors is given in the Design section.
- Align the device with the bracket and fix the position by pulling it down.
...
- Connect cables to the corresponding connectors of the device. Description of the connectors is given in the Design section.
- Align the device with the plastic bracket and secure the position by turning the device clockwise.
...
- Pull the device up (Figure 7).
- Remove the device.
Device management via the web interface
...
| Подсказка |
|---|
The spectrum analyzer on the radio interface operates only on channels that are reflected in the "Channels List" parameter. For example, if the Radio 2.4 GHz channel list contains channels '1 6 11', the spectrum analysis will only be performed for channels 1, 6 and 11. To add/remove channels from this list, go to the tab corresponding to this radio interface on the "Radio" page and make changes in the "Use Limit Channels" parameter. In order to analyze all the channels of the band on which the radio interface operates, go to the tab corresponding to the radio interface on the "Radio" page and uncheck the option "Use Limit Channels". After receiving the results of the spectrum analyzer, check the "Use Limit Channels" option again. For more information about configuring the radio interface via web interface, see the "Radio" menu section. |
| Scroll Pagebreak |
|---|
"Events" submenu
...
| Подсказка |
|---|
When configuring a WDS connection, it is necessary to select the same channel and channel width in the radio interface settings on the the devices that will be connected via WDS. Auto-channel should be disabled and the DFS option should be set to "off" or "forced". |
| Предупреждение |
|---|
When configuring a WDS connection on the Radio 2.4 GHz/Radio 5 GHz it is necessary to enable VAP0 on the Radio 2.4 GHz/Radio 5 GHz. The encryption modes on VAP and WDS interfaces should be the same. More detailed information about configuring VAPs can be found in the Virtual Wi-Fi access points (VAPs) configuration section. |
| Scroll Pagebreak |
|---|
...
- Interface – selecting and enabling the WDS interface on which the wireless bridge will be built;
- MAC address – MAC address of the radio interface on the remote device to which the wireless bridge is configured. The MAC address of the radio interface can be found in the remote device web interface, Monitoring/Radio information submenu. To configure WDS on the Radio 2.4 GHz, it is required to specify the MAC address of the remote device Radio 2.4 GHz. The configuration of WDS on the Radio 5 GHz is done in the same way — the MAC address of the remote device Radio 5 GHz is specified.
- Security Mode – security mode of access to the wireless network:
- Off – disable the encryption for data transmission;
- WPA2 – encryption method, when selected the following settings will be available:
- SSID – Wi-Fi network name;
- WPA Key – key/password required for connection to the remote access point. The key length is from 8 to 63 characters.
...
802.11r roaming is only possible between VAPs with security modes: WPA2 Personal and WPA2 Enterprise.
For instructions on configuring a VAP with different security modes, see section Firmware version 1.10.0 WEP-3ax. Usermanual.Configuration of VAP with WPA-Personal security mode.
Each VAP on access points should be configured individually, such as AP1(wlan1)↔AP2(wlan1), AP1(wlan0)↔AP2(wlan0), AP1(wlan1)↔AP3(wlan1), etc.
...
| Подсказка |
|---|
When configuring a WDS connection, it is necessary to select the same channel and channel width in the radio interface settings on the the devices that will be connected via WDS. Auto-channel should be disabled and the DFS option should be set to "off" or "forced". More detailed information about configuring the radio interface via the command line can be found in the Radio Settings section. |
| Предупреждение |
|---|
When configuring a WDS connection on the Radio 2.4/Radio 5 GHz it is necessary to enable VAP0 on the Radio 2.4/Radio 5 GHz. The encryption modes on VAP and WDS interfaces should be the same. More detailed information about configuring VAPs can be found in the Virtual Wi-Fi access points (VAPs) configuration section. |
Below is the configuration of a WDS connection on the Radio 5 GHz interface (wlan1).
...
| Подсказка |
|---|
The spectrum analyzer on the radio interface only works on the channels that are reflected in the "limit-channels" parameter. For example, if the wlan0 channel list contains channels '1 6 11', the spectrum analysis will only be performed for channels 1, 6 and 11. To analyze all channels of the band on which the radio interface operates, change the value of use-limit-channels in the radio interface settings to false. After receiving the results of the spectrum analyzer, return the value of use-limit-channels back to the original value – true. For more information about configuring the radio interface via CLI, see Radio configuration section. |
Scroll Pagebreak
...