Purpose

ESR series devices are the high performance multi-purpose network routers. Device combines traditional network features with a complex multi-tier approach to routing security, and ensures robust corporate environment protection.

Device has a built-in firewall that enables protection of your and organization network environment and supports latest data security, encryption, authentication and intrusion prevention features.

Device contains software and hardware means of data processing. Top performance is achieved through optimal distribution of data processing tasks between different subsets of the device.

Functions

Interface functions

Table 1 lists interface functions of the device.

Table 1 – Device interface functions

Cable connection polarity detection 
(Auto MDI/MDIX)

Automatic cable type detection–crossed or straight.

  • MDI (Medium Dependent Interface – straight) – cable standard for connection of terminal devices;
  • MDIX (Medium Dependent Interface with Crossover – crossed) – cable standard for connection of hubs and switches.


Back Pressure

The backpressure routing method is utilized in half-duplex connections for management of data streams, coming from the opposite devices, by means of collisions. This method allows to avoid buffer overruns and the loss of data.

Flow control
(IEEE 802.3X)

Flow control allows to interconnect the low-speed and the high-speed devices. To avoid buffer overrun, the low-speed device gains the ability to send PAUSE packets, that will force the high-speed device to pause the packet transmission.


(LAG, Link aggregation)

Link aggregation allows to increase the communication link bandwidth and robustness.

Router supports static and dynamic link aggregation. For dynamic aggregation, link group management is performed via LACP protocol.

MAC table functions

Table 2 lists MAC address processing functions of the device.

Table 2 – MAC address processing functions

MAC table

MAC address table sets the correspondence between MAC addresses and device interfaces and is used for data packet routing. Routers support table capacity up to 128K of MAC addresses and reserve specific MAC addresses for the system use.

Learning mode

MAC address table may contain either static addresses or addresses learnt during data packet transition through the device.

Learning involves registration of packet source MAC addresses with their binding to ports and VLANs. Afterwards, this data is used for incoming packet routing. Registered MAC address lifetime is limited. Administrator may adjust this setting.

If destination MAC address specified in the packet that was received by the device is not listed in the table, this packet will be sent further as a broadcast packet within L2 segment of the network.

Second-layer functions of OSI model

Table 3 lists second-layer functions and special aspects (OSI Layer 2).

Table 3 – Second-layer functions description (OSI Layer 2)

VLAN support

VLAN (Virtual Local Area Network) is a solution used for splitting a network into separate segments on L2 level. VLAN utilization allows to increase the operation stability for large networks by splitting them into smaller networks, isolate diversified data traffic by type and solve many other tasks.

Routers support various VLAN management methods:

  • VLAN based on data packet tagging according to IEEE802.1Q
  • VLAN based on device ports (port-based)
  • VLAN based on utilization of data classification policies (policy-based)

Spanning Tree Protocol1

The main task of Spanning Tree Protocol is to exclude redundant network links and convert network topology into the tree-like structure. Common areas of protocol application involve the prevention of network traffic loops and establishing of redundant communication links.

1  In the current firmware version, this functionality is supported only by ESR-1000 router

Third-layer functions of OSI model

Table 4 lists third-layer functions (OSI Layer 3).

Table 4 – Third-layer functions description (OSI Layer 3)

Static IP routes

Administrator of the router can add or remove static entries into/from the routing table.

Dynamic routing

 

With dynamic routing protocols, the device will be able to exchange the routing information with neighbouring routers and automatically create a routing table.

Router supports the following protocols: RIPv2, RIPng, OSPFv2, OSPFv3, IS-IS, BGP.

ARP table

ARP (Address Resolution Protocol) is a protocol used for resolution of the network and data-link layer addresses. ARP table contains information on the established correspondence.

Correspondence is established on the basis of the network device response analysis; device addresses are requested with broadcast packets.

DHCP client 

 

DHCP (Dynamic Host Configuration Protocol) protocol enables automation of the network device management process.

DHCP client allows the router to obtain the network address and additional settings from the external DHCP server. As a rule, this method is used for obtaining network settings of a public network operator (WAN).

DHCP server

DHCP server enables automation and centralization of the network device configuration process.

DHCP server allocated on a router allows for a complete solution for the local area network support.

DHCP server integrated into the router assigns IP addresses to network devices and transfers additional network settings, e.g. server addresses, network gateway addresses and other necessary settings.

DHCP Relay

The DHCP Relay functionality is designed to redirect broadcast DHCP Discover packets from one broadcast domain to unicast DHCP Discover packets in another broadcast domain.

NAT, Network Address Translation

Network address translation is a mechanism that translates IP addresses and port numbers for transit packets.

NAT function allows to minimize the quantity of IP address used through translation of multiple internal network IP addresses into a single external public IP address. NAT conceals local area network internal structure and allows to enhance its security.

Routers support the following NAT options:

  • Source NAT (SNAT) – the network address and the source port number will be replaced, when packet is transferred forth, and the destination address will be replaced in the response packet;
  • Destination NAT (DNAT) – external access is translated by the router to the user computer in LAN that has an internal address and thus directly inaccessible from outside the network (without NAT).

Traffic tunnelling functions

Table 5 – Traffic tunnelling functions

Tunnelling protocols

Tunneling is a method of packet conversion during their network transfer that involves the replacement, modification and addition of a new packet network header. This method may be used for negotiation of transport protocols when the data is transferred through the transit network as well as for creation of secured connections where tunnelled data is being encrypted.

Routers support the following types of tunnels:

  • GRE – IP packet/Ethernet frame is encapsulated into another IP packet with GRE (General Routing Encapsulation) header;
  • IPv4-IPv4 – tunnel that encapsulates source IP packets into IP packets with alternative network parameters;
  • L2TPv3 – tunnel for L2 traffic transmission using IP packets;
  • IPsec – tunnel with the encryption of transmitted data;
  • L2TP, PPTP, PPPoE, OpenVPN – tunnels used for establishing a remote 'client-sever' access.

Management and configuration functions

Table 6 – Basic management and configuration functions

Configuration file download and upload

Device parameters are saved into the configuration file that contains configuration data for the specific device ports as well as for the whole system. The following protocols may be used for file transfers: TFTP, FTP, and SCP.

Command line interface (CLI)

CLI management is performed locally via serial port RS-232, or remotely via Telnet, SSH. Console command line interface (CLI) is the industrial standard. CLI interpreter contains the list of commands and keywords that will help the user and reduce the amount of input data.

Syslog

Syslog protocol is designed for transmission of system event messages and event logging.

Ping, traceroute
network utilities

Ping and traceroute utilities allow you to check the availability of network devices and identify data transfer routes in IP networks.

Controlled access management – privilege levels

Routers support system access level management for users. Access levels enable responsibility areas management for device administrators. Access levels are numbered from 1 to 15; Level 15 stands for full access to device management features.

Authentication

Authentication is a user identity check procedure. Routers support the following authentication methods:

  • local – local user database stored on the device is used for authentication;
  • group – user database is located on the authentication server. RADIUS and TACACS protocols are user for server interactions.

SSH Server/
Telnet Server

SSH and Telnet server features allow you to establish connection to the device and perform device management.

Automatic configuration restore

Device features automatic configuration restore system designed to prevent remote access loss after re-configuration. If the configuration change is not confirmed in the specified time, configuration will be rolled back to the last known state.

Network security functions

Table 7 lists network security functions of the device.

Table 7 – Network security functions

Security zones

All router interfaces are distributed by security areas.

For each zone pair, you can set the rules that determine the possibility of data transmission between zones, data traffic filtering rules.

Data filtering

For each zone pair, you can specify the rule set that manages the filtering process for data transmitted through the router.

Device command interface provides appropriate means for detailed configuration of the traffic classification rules and to apply the resulting solution for traffic transmission.

Main specifications

Tble 8 lists main specifications of the router.

Table 8 – Main Specifications

General parameters

Interfaces

ESR-1700

4 x Combo Ethernet 10/100/1000BASE-T/1000BASE-X

8 x 10GBASE-R/1000BASE-X (SFP+/SFP)

2 x Hard disk installation slot

1 x Console RJ-45

1 x OOB port

2 x USB 2.0

ESR-3100

8 x Combo Ethernet 10/100/1000BASE-T/1000BASE-X 

8 x 10GBASE-R/1000BASE-X (SFP+/SFP)

1 x Console RJ-45

2 x USB 3.0

1 x SD card slot

ESR-1511

4 x Combo Ethernet 10/100/1000BASE-T/1000BASE-X 

4 x Ethernet 10/100/1000BASE-T (RJ-45)

4 x 10GBASE-R/1000BASE-X (SFP+/SFP)

2 x 40GBASE-X (QSFP+) 

1 x Console RJ-45

1 x OOB port

2 x USB 2.0

1 x SD card slot

ESR-1500

4 x Combo Ethernet 10/100/1000BASE-T/1000BASE-X 

4 x Ethernet 10/100/1000BASE-T (RJ-45)

4 x 10GBASE-R/1000BASE-X (SFP+/SFP)

1 x Console RJ-45

1 x OOB port

2 x USB 2.0

1 x SD card slot

ESR-1200

4 x Combo Ethernet 10/100/1000BASE-T/1000BASE-X 

12 x Ethernet 10/100/1000BASE-T (RJ-45)

8 x 10GBASE-R/1000BASE-X (SFP+/SFP)

1 x Console RJ-45

2 x USB 2.0

1 x SD card slot

ESR-1000

24 x Ethernet 10/100/1000BASE-T (RJ-45)

2 x 10GBASE-R/1000BASE-X (SFP+/SFP)

1 x Console RJ-45

2 x USB 2.0

1 x SD card slot

ESR-200

4 x Combo Ethernet 10/100/1000BASE-T/1000BASE-X 

4 x Ethernet 10/100/1000BASE-T (RJ-45)

1 x Console RJ-45

1 x USB 3.0

1 x USB 2.0

1 x SD card slot

ESR-100

4 x Combo Ethernet 10/100/1000BASE-T/1000BASE-X 

1 x Console RJ-45

1 x USB 3.0

1 x USB 2.0

1 x SD card slot

ESR-21

8 x Ethernet 10/100/1000BASE-T (RJ-45)

4 x 1000BASE-X (SFP)

3 x Serial port RS-232

1 x Console RJ-45

1 x USB 3.0

1 x USB 2.0

1 x SD card slot

ESR-20

2 x Combo Ethernet 10/100/1000BASE-T/1000BASE-X 

2 x Ethernet 10/100/1000BASE-T (RJ-45)

1 x Console RJ-45

1 x USB 3.0

1 x USB 2.0

1 x SD card slot

ESR-14VF

8 x Ethernet 10/100/1000BASE-T (RJ-45)

1 x 1000BASE-X (SFP)

1 x Console RJ-45

4 x FXS

2 x USB 2.0

ESR-12VF

8 x Ethernet 10/100/1000BASE-T (RJ-45)

1 x 1000BASE-X (SFP)

1 x Console RJ-45

3 x FXS

1 x FXO

2 x USB 2.0

ESR-12V

8 x Ethernet 10/100/1000BASE-T (RJ-45)

1 x Console RJ-45

3 x FXS

1 x FXO

2 x USB 2.0

ESR-10

4 x Ethernet 10/100/1000BASE-T (RJ-45)

2 x 1000BASE-X (SFP)

1 x Console RJ-45

2 x USB 2.0

Types of optical transceivers

ESR-1511

1000BASE-X SFP

10GBASE-R SFP+

40GBASE-X QSFP+

ESR-1700

ESR-3100

ESR-1500

ESR-1200

ESR-1000

1000BASE-X SFP

10GBASE-R SFP+

ESR-200

ESR-100

ESR-21

ESR-20

ESR-14VF

ESR-12VF

ESR-10

1000BASE-X SFP

Duplex or half-duplex interface modes

  • duplex and half-duplex modes for electric ports
  • duplex mode for optical ports

Maximum bandwidth in
L2 mode (hardware switching)

ESR-1700

ESR-1511

ESR-1500

ESR-1200

160 Gbps

ESR-1000

88 Gbps

Data transfer rate

ESR-1511

  • electrical interfaces 10/100/1000Mbps
  • optical interfaces 1/10/40 Gbps

ESR-1700

ESR-3100

ESR-1500

ESR-1200

ESR-1000

  • electrical interfaces 10/100/1000Mbps
  • optical interfaces 1/10Gbps

ESR-200

ESR-100

ESR-21

ESR-20

ESR-14VF

ESR-12V(F)

ESR-10

  • electrical interfaces 10/100/1000Mbps
  • optical interfaces 1Gbps

Number of VPN tunnels


ESR-1700

ESR-3100

ESR-1511

ESR-1500

ESR-1200

ESR-1000

500

ESR-200

ESR-100

ESR-21

ESR-20

250

ESR-14VF

ESR-12V(F)

ESR-10

10

Quantity of static routes

ESR-1700

ESR-3100

ESR-1511

ESR-1500

ESR-1200

ESR-1000

ESR-200

ESR-100

ESR-21

ESR-20

11k

ESR-14VF

ESR-12V(F)

ESR-10

1k

Number of competitive sessions

ESR-1700

ESR-3100

ESR-1511

ESR-1500

ESR-1200

ESR-1000

512k

ESR-200

ESR-100

ESR-21

ESR-20

256k

ESR-14VF

ESR-12V(F)

ESR-10

4k

VLAN support

up to 4k active VLANs according to 802.1Q

Number of BGPv4/BGPv6 routes

ESR-1700

ESR-3100

ESR-1511

ESR-1500

ESR-1200

ESR-1000

5M

ESR-200

ESR-100

ESR-21

ESR-20

2.5M

ESR-14VF

ESR-12V(F)

ESR-10

1M

Number of OSPFv2/OSPFv3/ISIS routes

ESR-1700

ESR-3100

ESR-1511

ESR-1500

ESR-1200

ESR-1000

500k

ESR-200

ESR-100

ESR-21

ESR-20

300k

ESR-14VF

ESR-12V(F)

ESR-10

30k

Number of RIP/RIPng routes

10k

MAC address table


ESR-1700

ESR-1511

ESR-1500

ESR-1200

128k entries

ESR-1000

16k entries

ESR-3100

ESR-200

ESR-100

ESR-21

ESR-20

ESR-14VF

ESR-12V(F)

ESR-10

2k bridge entries

FIB size





ESR-1700

3,0M

ESR-3100

ESR-1511

ESR-1500

ESR-1200

ESR-1000

1.7M

ESR-200

ESR-100

ESR-21

ESR-20

1.4M

ESR-14VF

ESR-12V(F)

ESR-10

1M

VRF Lite

32

L3 interfaces

ESR-1700

ESR-3100

ESR-1500

ESR-1511

ESR-1200

ESR-1000

ESR-200

ESR-100

ESR-21

ESR-20

4000

ESR-14VF

ESR-12V(F)

ESR-10

200

Compliance

IEEE 802.3 10BASE-T Ethernet

IEEE 802.3u 100BASE-T Fast Ethernet

IEEE 802.3ab 1000BASE-T Gigabit Ethernet

IEEE 802.3z Fiber Gigabit Ethernet

IEEE 802.3ba 40GBASE-SR4, 40GBASE-LR4

ANSI/IEEE 802.3 Speed autodetection

IEEE 802.3x Data flow control

IEEE 802.3ad LACP link aggregation

IEEE 802.1q VLAN virtual local networks

IEEE 802.1v

IEEE 802.3ac

IEEE 802.3ae

IEEE 802.1D

IEEE 802.1w

IEEE 802.1s

Control

Local control

CLI

Remote control

TELNET, SSH

Physical specifications and ambient conditions

Power supply

ESR-1700

AC: 176–264 V, 50–60 Hz

DC: 36–72 V

Power options:

  • single AC or DC power supply;
  • two AC or DC power supplies with hot swapping.


ESR-3100

ESR-1511

ESR-1500

ESR-1200

ESR-1000

AC: 100–240 V, 50–60 Hz

DC: 36–72 V

Power options:

  • single AC or DC power supply;
  • two AC or DC power supplies with hot swapping.

ESR-200

ESR-100

ESR-21

ESR-20

ESR-14VF

ESR-12V(F)

AC: 100–264 V, 50–60 Hz

ESR-10

220 V/12 V, 1.5 A DC power adapter

Maximum power consumption:


ESR-1700

250 W

ESR-3100

123 W

ESR-1511

128 W

ESR-1500

125 W

ESR-1200

85 W

ESR-1000

75 W

ESR-200

25 W

ESR-100

20 W

ESR-21

32 W

ESR-20

25 W

ESR-14VF

ESR-12V(F)

22 W

ESR-10

9 W

Weight



ESR-1700

12 kg max

ESR-3100

5 kg max

ESR-1511

ESR-1500

7 kg max

ESR-1200

5.5 kg max

ESR-1000

3.6 kg max

ESR-200

ESR-100

2.5 kg max

ESR-21

3.15 kg max

ESR-20

2 kg max

ESR-14VF

ESR-12V(F)

ESR-10

1 kg max

Dimensions (WxHxD)




ESR-1700

440x88x490 mm

ESR-3100

ESR-1511

ESR-1500

430x44x425 mm

ESR-1200

ESR-1000

430x44x352 mm

ESR-200

ESR-100

310х44x240 mm

ESR-21

430х44x225 mm

ESR-20

267х44x212 mm

ESR-14VF

ESR-12V(F)

267x43.6x160.5 mm

ESR-10

185x32x118 mm

Operating temperature range

ESR-1700

ESR-3100

ESR-1511

ESR-1500

ESR-1200

ESR-1000

ESR-200

ESR-100

ESR-21

ESR-20

-10 to +45 °C

ESR-14VF

ESR-12V(F)

ESR-10

0 to +40 °C

Storage temperature range

-40 to +70 °C

Operation relative humidity (non-condensing)

up to 80%

Storage relative humidity (non-condensing)

from 10% to 95%

Lifetime

at least 15 years

Design

This section describes the design of the device. Depicted front, rear, and side panels of the device, connectors, LED indicators and controls.

The device has a metal housing available for 19” form-factor rack mount; housing size is 1U.

ESR-1700 design

ESR-1700 front panel

The front panel layout is depicted in figure 1.

Figure 1 – ESR-1700 front panel

Table 9 lists connectors, LEDs and controls located on the front panel of ESR-1700.

Table 9 – Description of ESR-1700 connectors, LEDs and front panel controls

№

Front panel element

Description

1

HDD1

Connector for HDD installation.

2

HDD2

Connector for HDD installation.

3

USB1

Port for USB device connection.

4

USB2

Port for USB device connection.

5

Combo Ports [1 .. 4]

4 ports of Gigabit Ethernet 10/100/1000BASE-X (SFP).

6

XG1 – XG8

Slots for 10G SFP+/1G SFP transceivers.

7

Status

Current device status LED.

Alarm

Alarm LED.

VPN

VPN gateway operation mode LED (is not supported in the current version).

Flash

Activity of exchange with data storage – SD card or USB Flash.

Power

Device power LED.

Master

Failover mode operation LED (is not supported in the current version).

Fan

Fan operation LED.

RPS

Redundant power supply LED.

8

F

Functional key that reboots the device and resets it to factory default configuration:

  • Pressing the key for less than 10 seconds reboots the device;
  • Pressing the key for more than 10 seconds resets the terminal to factory settings.

9

Console

Console port RS-232 for local management of the device.

10

OOB

Ethernet port for router management.

ESR-1700 rear panel

The rear panel of ESR-1700 is shown in the picture below.

Figure 2 – ESR-1700 rear panel

Table 10 lists rear panel connectors of the router.

Table 10 – Rear panel connectors description

№

Description

1

Earth bonding point of the device.

2

Hot-swappable removable ventilation modules.

3

Main power supply.

4

Place for installation of a redundant power supply.

ESR-1700 side panels

The side panel layout of ESR-1700 is depicted in figures 3 and 4.

Figure 3 – ESR-1700 right side panel

Figure 4 – ESR-1700 left side panel

Side panels of the device have air vents for heat removal. Do not block air vents. This may cause the components to overheat, which may result in device malfunction. For recommendations on device installation, see section Installation and connection. Firmware version 1.13.0.

ESR-3100 design

ESR-3100 front panel

The front panel layout is depicted in 5.

Figure 5 – ESR-3100 front panel

Table 11 lists connectors, LEDs and controls located on the front panel of ESR-3100.

Table 11 – Description of connectors, LEDs and controls located on ESR-3100 front panel

№

Front panel element

Description

1

Status

Current device status LED.

Alarm

Alarm LED.

VPN

VPN gateway operation mode LED.

Flash

Activity of exchange with data storage – SD card or USB Flash.

Power

Device power LED.

Master

Failover mode operation LED (is not supported in the current version).

Fan

Fan operation LED.

RPS

Redundant power supply LED.

2

F

Functional key that reboots the device and resets it to factory default configuration:

  • Pressing the key for less than 10 seconds reboots the device;
  • Pressing the key for more than 10 seconds resets the terminal to factory settings.

3

Console

Console port RS-232 for local management of the device.

4

SD

SD-card connector.

5

USB1

USB 3.0 port for USB device connection.

6

USB2

USB 3.0 port for USB device connection.

7

[1 .. 8]

8 ports of Gigabit Ethernet 10/100/1000BASE-T (RJ-45).

8

XG1 – XG8

Slots for 10G SFP+/1G SFP transceivers.

ESR-3100 rear panel

The rear panel of ESR-3100 is depicted in the figure below.

Figure 6 – ESR-3100 rear panel

Table 12 lists rear panel connectors of the router.

Table 12 – Rear panel connectors description

№

Description

1

Main power supply.

2

Earth bonding point of the device.

3

Hot-swappable removable ventilation modules.

4

5

Place for installation of a redundant power supply.

ESR-3100 side panels

The side panel layout of ESR-3100 is depicted in figures 7 and 8.

Figure 7 – ESR-3100 right side panel

Figure 8 – ESR-3100 left side panel

Side panels of the device have air vents for heat removal. Do not block air vents. This may cause the components to overheat, which may result in device malfunction. For recommendations on device installation, see section Installation and connection. Firmware version 1.13.0.

ESR-1511, ESR-1510 design

ESR-1511 front panel

The front panel layout is depicted in figure 9.


Figure 9 – ESR-1511 front panel

Table 13 lists connectors, LEDs and controls located on the front panel of ESR-1511.

Table 13 – Description of connectors, LEDs and controls located on ESR-1511 front panel

№

Front panel element

Description

1

Status

Current device status LED.

Alarm

Alarm LED.

VPN

VPN gateway operation mode LED (is not supported in the current version).

Flash

Activity of exchange with data storage – SD card or USB Flash.

Power

Device power LED.

Master

Failover mode operation LED (is not supported in the current version).

Fan

Fan operation LED.

RPS

Redundant power supply LED.

2

Console

Console port RS-232 for local management of the device.

3

OOB

Ethernet port for router management.

4

SD

SD-card connector.

5

USB1

Port for USB device connection.

6

F

Functional key that reboots the device and resets it to factory default configuration:

  • Pressing the key for less than 10 seconds reboots the device;
  • Pressing the key for more than 10 seconds resets the terminal to factory settings.

7

USB2

Port for USB device connection.

8

Ethernet

4 ports of Ethernet 10/100/1000BASE-T.

9

Combo Ports [1 .. 4]

4 ports of Gigabit Ethernet 10/100/1000BASE-X (SFP).

10

XG1 – XG4

Slots for 10G SFP+/1G SFP transceivers.

11

XLG1 – XLG2

Slots for 40G QSFP+ transceivers.

ESR-1500 front panel

The front panel layout is depicted in figure 10.


Figure 10 – ESR-1500 front panel

Table 14 lists connectors, LEDs and controls located on the front panel of ESR-1500.

Table 14 – Description of ESR-1500 connectors, LEDs and front panel controls

№

Front panel element

Description

1

Status

Current device status LED.

Alarm

Alarm LED.

VPN

VPN gateway operation mode LED (is not supported in the current version).

Flash

Activity of exchange with data storage – SD card or USB Flash.

Power

Device power LED.

Master

Failover mode operation LED (is not supported in the current version).

Fan

Fan operation LED.

RPS

Redundant power supply LED.

2

Console

Console port RS-232 for local management of the device.

3

OOB

Ethernet port for router management.

4

SD

SD-card connector.

5

USB1

Port for USB device connection.

6

F

Functional key that reboots the device and resets it to factory default configuration:

  • Pressing the key for less than 10 seconds reboots the device;
  • Pressing the key for more than 10 seconds resets the terminal to factory settings.

7

USB2

Port for USB device connection.

8

Ethernet

4 ports of Ethernet 10/100/1000BASE-T.

9

Combo Ports [1 .. 4]

4 ports of Gigabit Ethernet 10/100/1000BASE-X (SFP).

10

XG1 – XG4

Slots for 10G SFP+/1G SFP transceivers.

ESR-1511, ESR-1500 rear panel

The rear panel layout of ESR-1511 and ESR-1500 routers is depicted in figure 11.

Figure 11 – ESR-1511, ESR-1500 rear panel

Table 15 lists rear panel connectors of the router.

Table 15 – Rear panel connectors description

№

Description

1

Main power supply.

2

Earth bonding point of the device.

3

Hot-swappable removable ventilation modules.

4

Place for installation of a redundant power supply.

ESR-1511, ESR-1500 side panels

The side panel layout of ESR-1511, ESR-1500 is depicted in Figures 12 and 13.

Figure 12 – ESR-1511, ESR-1500 right side panel

Figure 13 – ESR-1511, ESR-1500 left side panel

Side panels of the device have air vents for heat removal. Do not block air vents. This may cause the components to overheat, which may result in device malfunction. For recommendations on device installation, see section Installation and connection. Firmware version 1.13.0.

ESR-1200, ESR-1000 design

ESR-1200 front panel

The front panel layout is depicted in 14.

Figure 14 – ESR-1200 front panel

Table 16 lists connectors, LEDs and controls located on the front panel of ESR-1200.

Table 16 – Description of connectors, LEDs and controls located on the front panel of ESR-1200

№

Front panel element

Description

1

SD

SD-card connector.

2

USB1

Port for USB device connection.

3

USB2

Port for USB device connection.

4

[1 .. 12]

12 ports of Gigabit Ethernet 10/100/1000BASE-T (RJ-45).

5

Combo Ports

4 ports of Gigabit Ethernet 10/100/1000BASE-X (SFP).

6

XG1 – XG8

Slots for installation of 10G SFP+/1G SFP transceivers.

7

Status

Current device status LED.

Alarm

Alarm LED.

HA

НА operation mode LED.

Flash

Activity indicator of exchange with data storages (SD-card or USB Flash).

Power

Device power LED.

Master

Indicator of failover modes operation.

Fan

Fan operation LED.

RPS

Redundant power supply LED.

8

F

Functional key that reboots the device and resets it to factory default configuration:

  • Pressing the key for less than 10 seconds reboots the device;
  • Pressing the key for more than 10 seconds resets the terminal to factory settings.

9

Console

Console port RS-232 for local management of the device.

ESR-1000 front panel

The front panel layout is depicted in 15.

Figure 15 – ESR-1000 front panel

Table 17 lists sizes, LEDs and controls located on ESR-1000 front panel.

Table 17 – Description of connectors, LEDs and controls located on ESR-1000 front panel

№

Front panel element

Description

1

SD

SD-card connector.

2

USB1

Port for USB device connection.

3

USB2

Port for USB device connection.

4

XG1, XG2

Slots for 10G SFP+/1G SFP transceivers.

5

[1 .. 24]

24 ports of Gigabit Ethernet 10/100/1000BASE-T (RJ-45).

6

Status

Current device status LED.

Alarm

Alarm LED.

VPN

Active VPN sessions indicator.

Flash

Activity indicator of exchange with data storages (SD-card or USB Flash).

Power

Device power LED.

Master

Indicator of failover modes operation.

Fan

Fan operation LED.

RPS

Redundant power supply LED.

7

F

Functional key that reboots the device and resets it to factory default configuration:

  • Pressing the key for less than 10 seconds reboots the device;
  • Pressing the key for more than 10 seconds resets the terminal to factory settings.

8

Console

Console port RS-232 for local management of the device.

ESR-1200, 1000 rear panel

The rear panel of ESR-1000 is depicted in the figure below.

The figure shows the router delivery package with a single AC power supply.

Figure 16 – ESR-1000 rear panel

Table 18 lists rear panel connectors of the router.

Table 18 – Rear panel connectors description

№

Description

1

Main power supply.

2

Place for installation of a redundant power supply.

3

Hot-swappable removable ventilation modules.

4

Earth bonding point of the device.

ESR-1200, ESR-1000 side panels

The side panel layout of ESR-1200, ESR-1000 is depicted in Figures 17 and 18.

Figure 17 – ESR-1200, 1000 right side panel

Figure 18 – ESR-1200, 1000 left side panel

Side panels of the device have air vents for heat removal. Do not block air vents. This may cause the components to overheat, which may result in device malfunction. For recommendations on device installation, see section Installation and connection. Firmware version 1.13.0.

ESR-200, ESR-100 design

ESR-100, ESR-200 front panel

The front panel layout of ESR-200 is depicted in figure 19.

Figure 19 – ESR-200 front panel

The front panel layout of ESR-100 is depicted in figure 20.

Figure 20 – ESR-100 front panel

Table 19 lists connectors, LEDs and controls located on the front panel of ESR-100 and ESR-200 routers.

Table 19 – Description of connectors, LEDs and controls located on ESR-200, ESR-100 front panel

№

Front panel element

Description

1

SD

SD-card connector.

2

USB1, USB2

2 x USB-enabled devices connection port.

3

[1 .. 4]

4 ports of Gigabit Ethernet 10/100/1000BASE-T (RJ-45).

4

Combo Ports

4 ports of Gigabit Ethernet 10/100/1000BASE-X (SFP).

5

Power

Device power LED.

Status

Current device status LED.

Alarm

Alarm LED.

Fan

Fan operation LED.

6

F

Functional key that reboots the device and resets it to factory default configuration:

  • Pressing the key for less than 10 seconds reboots the device;
  • Pressing the key for more than 10 seconds resets the terminal to factory settings.

7

Console

Console port RS-232 for local management of the device.

8

110-250 VAC
60/50 Hz max 1A

Power supply.

ESR-200, ESR-100 rear panel

The rear panel layout of ESR-200 and ESR-100 routers is depicted in figure 21.

Figure 21 – ESR-200, ESR-100 rear panel

Table 20 lists rear panel connectors of the router.

Table 20 – Rear panel connectors description

№

Description

1

Earth bonding point of the device.

2

Ventilation module.

ESR-100, ESR-200 side panels

The side panel layout of ESR-200, ESR-100 is depicted in Figures 22 and 23.

Figure 22 – ESR-100 and ESR-200 right side panel

Figure 23 – ESR-100 and ESR-200 left side panel

ESR-21 design

The device has a metal housing available for 19” form-factor rack mount; housing size is 1U.

ESR-21 front panel

The front panel layout of ESR-21 is depicted in figure 24.

Figure 24 – ESR-21 front panel

Table 21 lists sizes, LEDs and controls located on ESR-21 front panel.

Table 21 – Description of connectors, LEDs and controls located on ESR-21 front panel

№

Front panel element

Description

1

220V АC

Power supply

2

Power

Device power LED

Status

Device status LED

Alarm

Device alarm presence and level LED

HA

HA operation mode LED (is not supported in the current version)

3

F

Functional key that reboots the device and resets it to factory default configuration: - pressing the key for less than 10 seconds reboots the device. - pressing the key for more than 10 seconds resets the device to factory default configuration.

4

SD

SD-card connector

5

USB1

USB 2.0 connector for connecting external USB devices

6

USB2

USB 3.0 connector for connecting external USB devices

7

Console

Console port for local management of the device

8

RS-232

3 serial ports

9

[1 .. 8]

8 ports of Gigabit Ethernet 10/100/1000BASE-T (RJ-45)

10

Optical Port

4 ports of Gigabit Ethernet 10/100/1000BASE-X (SFP)

ESR-21 rear panel

The rear panel layout of ESR-21 is depicted in figure 25.

Figure 25 – ESR-21 rear panel

Table 22 lists rear panel connectors of the router.

Table 22 – Rear panel connectors description

№

Description

1

Earth bonding point of the device.

ESR-21 side panels

The side panel layout of ESR-21 is depicted in figures 26 and 27.

Figure 26 – ESR-21 left side panel

Figure 27 – ESR-21 right side panel

Side panels of the device have air vents for heat removal. Do not block air vents. This may cause the components to overheat, which may result in device malfunction. For recommendations on device installation, see section Installation and connection. Firmware version 1.13.0.

ESR-20 design

The device has a metal housing available for 19” form-factor rack mount; housing size is 1U.

ESR-20 front panel

The front panel layout is depicted in figure 28.

Figure 28 – ESR-20 front panel

Table 23 lists connectors, LEDs and controls located on the front panel of ESR-20.

Table 23 – Description of connectors, LEDs and controls located on ESR-20 rear panel

№

Front panel element

Description

1

110-250 VАC

Power supply.

2

Power

Device power LED.

Status

Current device status LED.

Alarm

Alarm LED.

HA

HA operation mode LED (is not supported in the current version).

3

F

Functional key that reboots the device and resets it to factory default configuration: - pressing the key for less than 10 seconds reboots the device. - pressing the key for more than 10 seconds resets the device to factory default configuration.

4

Console

Console port for local management of the device.

5

SD

SD-card connector.

6

USB1

USB 2.0 connector for connecting external USB devices.

7

USB2

USB 3.0 connector for connecting external USB devices.

8

1, 2

2 ports of Gigabit Ethernet 10/100/1000BASE-T (RJ-45).

9

[1 .. 4]

2 Combo ports of Ethernet 10/100/1000BASE-X/10/100/1000BASE-T.

ESR-20 rear panel

The rear panel layout of ESR-20 is depicted in figure 29.

Figure 29 – ESR-20 rear panel

Table 24 lists rear panel connectors of the router.

Table 24 – Rear panel connectors description

№

Description

1

Earth bonding point of the device.

ESR-20 side panels

The side panel layout of ESR-20 is depicted in figures 30 and 31.

Figure 30 – ESR-20 left side panel

Figure 31 – ESR-20 right side panel

Side panels of the device have air vents for heat removal. Do not block air vents. This may cause the components to overheat, which may result in device malfunction. For recommendations on device installation, see section Installation and connection. Firmware version 1.13.0.

ESR-12VF, ESR-14VF design

The device has a metal housing available for 19” form-factor rack mount; housing size is 1U.

ESR-12VF, ESR-14VF front panel

The front panel layout is depicted in figure 32.

Figure 32 – ESR-12VF, ESR-14VF front panel

Table 25 lists connectors, LEDs and controls located on the front panel of ESR-12VF and ESR-14VF routers.

Table 25 – Description of connectors, LEDs and controls located on ESR-12VF, ESR-14VF front panel

№

Front panel element

Description

1

220V АC

Power supply.

2

Power

Device power LED.

3

Console

Console port RS-232 for local management of the device.

4

F

Functional key that reboots the device and resets it to factory default configuration: - pressing the key for less than 10 seconds reboots the device. - pressing the key for more than 10 seconds resets the device to factory default configuration.

5

USB1, USB2

2 USB connectors for connecting external USB devices.

6

FXO

PSTN external subscriber line LED.

1,2,3

Internal subscriber terminals LED.

7

FXO

1 FXO connector for connection PSTN external subscriber line (only for ESR-12VF).

8

FXS 1, FXS 2, FXS 3

3 connectors for internal subscriber terminals (for ESR-12VF).

FXS 1, FXS 2, FXS 3

4 connectors for internal subscriber terminals (for ESR-14VF).

9

[1 .. 8]

8 ports of Gigabit Ethernet 10/100/1000BASE-T (RJ-45).

10

Optical Port

1 port of Gigabit Ethernet-100/1000BASE-X (SFP)

11

1,2

Optical interfaces LED

ESR-14VF, ESR-12VF rear panel

The rear panel layout of ESR-12VF, ESR-14-VF is depicted in figure 33.

Figure 33 – ESR-12VF, ESR-14VF rear panel

Table 26 lists rear panel connectors of the router.

Table 26 – Rear panel connectors description

№

Description

1

Earth bonding point of the device.

ESR-12VF, ESR-14VF side panels

The side panel layout of ESR-12VF, ESR-14VF is depicted in Figures 34 and 35.

Figure 34 – ESR-12VF, ESR-14VF left side panel

Figure 35 – ESR-12VF, ESR-14VF right side panel

Side panels of the device have air vents for heat removal. Do not block air vents. This may cause the components to overheat, which may result in device malfunction. For recommendations on device installation, see section Installation and connection. Firmware version 1.13.0.

ESR-12V design

The device has a metal housing available for 19” form-factor rack mount; housing size is 1U.

ESR-12V front panel

The front panel layout is depicted in figure 36.

Figure 36 – ESR-12V front panel

Table 27 lists connectors, LEDs and controls located on the front panel of ESR-12VF router.

Table 27  – Description of connectors, LEDs and controls located on ESR-12V front panel

№

Front panel element

Description

1

220V АC

Power supply.

2

Power

Device power LED.

3

Console

Console port RS-232 for local management of the device.

4

F

Functional key that reboots the device and resets it to factory default configuration: - pressing the key for less than 10 seconds reboots the device. - pressing the key for more than 10 seconds resets the device to factory default configuration.

5

USB1, USB2

2 USB connectors for connecting external USB devices.

6

FXO

PSTN external subscriber line LED.

1,2,3

Internal subscriber terminals LED.

7

FXO

1 FXO connector for connection PSTN external subscriber line.

8

FXS 1, FXS 2, FXS 3

3 connectors for internal subscriber terminals.

9

[1 .. 8]

8 ports of Gigabit Ethernet 10/100/1000BASE-T (RJ-45).

ESR-12V rear panel

The rear panel layout of ESR-12V is depicted in 37.

Figure 37 – ESR-12V rear panel

Table 28 lists rear panel connectors of the router.

Table 28 – Rear panel connectors description

№

Description

1

Earth bonding point of the device.

ESR-12V side panels

The side panel layout of ESR-12V is depicted in figures 38 and 39.

Figure 38 – ESR-12V left side panel

Figure 39 – ESR-12V right side panel

Side panels of the device have air vents for heat removal. Do not block air vents. This may cause the components to overheat, which may result in device malfunction. For recommendations on device installation, see section Installation and connection. Firmware version 1.13.0.

ESR-10 design

ESR-10 rear panel

The rear panel layout of the device is depicted in figure 40.

Figure 40 – ESR-10 rear panel

Table 29 lists connectors, LEDs and controls located on the rear panel of ESR-10.

Table 29 – Description of connectors, LEDs and controls located on ESR-10 rear panel

№

Front panel element

Description

1

ON/OFF

Power on/off button

2

12V DC

Connector for power adapter connection

3

Console

RS-232 console port for local management of the device

4

USB1, USB2

2 USB connectors for connecting external USB devices

5

[1 .. 4]

4 ports of Gigabit Ethernet – 10/100/1000BASE-T (RJ-45)

6

Optical Ports

2 ports of Gigabit Ethernet-100/1000BASE-X (SFP)

ESR-10 side panels

The side panel layout of ESR-10 is depicted in figure 41.

Figure 41 – ESR-10 side panel

Table 30 lists right panel controls of the router.

Table 30 – Right panel connectors description

№

Side panel element

Description

1

F

Functional key that reboots the device and resets it to factory default configuration:

  • pressing the key for less than 10 seconds reboots the device.
  • pressing the key for more than 10 seconds resets the device to factory default configuration.

ESR-10 top panel

The top panel layout of ESR-10 is depicted in figure 42.

Figure 42 – ESR-10 top panel

Table 31 lists LEDs located on ESR-10 top panel.

Table 31 – Description of front panel LEDs

№

Top panel element

Description

1

Power

Device power and operation status LED

2

-

The LED is not used

3

USB1, USB2

External USB devices LED

4

[1 .. 4]

Ethernet ports LED

5

[5 .. 6]

Optical interfaces LED

Light Indication

ESR-1700, ESR-1511, ESR-1500, ESR-1200, ESR-1000 light indication

Gigabit Ethernet copper interface statuses are represented by two LEDs – green LINK/ACT LED and amber SPEED LED. Location of the copper interface LEDs is depicted in figure 43. SFP interface status is represented by two LEDs – RX/ACT and TX/ACT – depicted in figure 44. For light indication meaning, see Tables 32 and 33 respectively.

Figure 43 – Location of RJ-45 connector indicators

Figure 44 – Location of optical interface indicators

Table 32 – Light indication of copper interface status

SPEED indicator is lit

LINK/ACT indicator is lit

Ethernet interface state

Off

Off

The port is disabled or connection is not established.

Off

Solid on

10Mbps or 100Mbps connection is established.

Solid on

Solid on

1000Mbps connection is established.

X

Flashes

Data transfer is in progress.

Table 33 – Light indication of SFP/SFP+/QSFP+ interface status

RX/ACT indicator is lit

TX/ACT indicator is lit

Ethernet interface state

Off

Off

The port is disabled or connection is not established.

Solid on

Solid on

Connection established.

Flashes

X

Data reception in progress.

X

Flashes

Data transfer is in progress.

The following table lists description of system indicator statuses and meanings.

Table 34 – Status of system indicators

Indicator name

Indicator function

LED State

Device State

Status

Current device status LED.

Green

Device is in normal operation state.

Orange

Device is booting up the software.

Alarm

Alarm LED.

-

-

VPN

Active VPN sessions indicator.

-

-

Flash

Activity indicator of exchange with data storages: SD-card or USB Flash.

Orange

Read/write operation execution with 'copy' command.

Power

Device power LED.

Green

Device power is OK. Main power supply, if installed, is operational.

Orange

Main power supply failure, fault, or the primary network is missing.

Off

Device internal power supply failure.

Master

Indicator of failover modes operation.

-

-

Fan

Cooling fan status.

Off

All fans are operational.

Red

One or more fans has failed. Possible cause of failure: at least one of the fans has stopped or is working at lower rpm.

RPS

Backup power supply operation mode.

Green

Backup power supply is installed and operational.

Off

Backup power supply is not installed.

Red

Backup power supply is missing or failed.

ESR-200/ESR-100 light indication

Gigabit Ethernet copper interface and SFP interface statuses are represented by two LEDs – green LINK/ACT LED and amber SPEED LED. Location of the copper interface LEDs is depicted in figure 43. SFP interface status is depicted in figure 45. For light indication meaning, see Table 35.

Figure 45 – Location of optical interface indicators

Table 35 – Light indication of copper and SFP interface status

SPEED indicator is lit

LINK/ACT indicator is lit

Ethernet interface state

Off

Off

The port is disabled or connection is not established.

Off

Solid on

10Mbps or 100Mbps connection is established.

Solid on

Solid on

1000Mbps connection is established.

X

Flashes

Data transfer is in progress.

The following table lists description of system indicator statuses and meanings.

Table 36 – Status of system indicators

Indicator name

Indicator function

LED State

Device State

Status

Current device status LED.

Green

Device is in normal operation state.

Orange

Device is booting up the software.

Alarm

Device alarm presence and level indicator1.

-

-

Power

Device power LED.

Green

Device power is OK. Main power supply, if installed, is operational.

Orange

Main power supply failure, fault, or the primary network is missing.

Off

Device internal power supply failure.

Fan

Cooling fan status.

Off

All fans are operational.

Red

One or more fans has failed. Possible cause of failure: at least one of the fans has stopped or is working at lower rpm.

1 Not supported in the current firmware version

ESR-21/ESR-20 light indication

Gigabit Ethernet copper interface statuses are represented by two LEDs – green LINK/ACT LED and amber SPEED LED.

Table 37 – Light indication of copper and SFP interface status

SPEED indicator is lit

LINK/ACT indicator is lit

Ethernet interface state

Off

Off

The port is disabled or connection is not established.

Off

Solid on

10Mbps or 100Mbps connection is established.

Solid on

Solid on

1000 Mbps connection is established.

X

Flashes

Data transfer is in progress.

Figure 46 – Location of SFP connector indicators

Figure 47 – Location of RJ-45 connector indicators

The following table lists description of system indicator statuses and meanings.

Table 38 – Status of system indicators

Indicator name

Indicator function

LED State

Device State

Power

Device power LED.

Green

Device power is OK. Main power supply, if installed, is operational. The main software is uploaded.

Red

The main software is not loaded.

Off

Device internal power supply failure.

Status

Current device status LED.

Green

Device is in normal operation state.

Orange

Device is booting up the software.

Alarm

Alarm LED.

-

-

HA

HA operation mode LED (is not supported in the current version)

-

-

ESR-12V(F) light indication

Gigabit Ethernet copper interface statuses are represented by two LEDs – green LINK/ACT LED and amber SPEED LED.

Table 39 – Light indication of copper and SFP interface status

SPEED indicator is lit

LINK/ACT indicator is lit

Ethernet interface state

Off

Off

Port is disabled or connection is not established

Off

Solid on

10Mbps or 100Mbps connection is established

Solid on

Solid on

1000Mbps connection is established

X

Flashes

Data transfer is in progress

Figure 48 – Location of SFP connector indicators (only for ESR-12VF, ESR-14VF)

Figure 49 – Location of RJ-45 connector indicators

The following table lists description of system indicator statuses and meanings.

Table 40 – Status of system indicators

Indicator name

Indicator function

LED State

Device State

Power

Device power LED.

Green

Device power is OK. Main power supply, if installed, is operational. The main software is uploaded.

Red

The main software is not uploaded.

Off

Device internal power supply failure.

ESR-10 light indication

Gigabit Ethernet copper interfaces statuses are represented by amber SPEED LED.

Table 41 – Light indication of copper interface status

SPEED indicator is lit

Ethernet interface state

Off

Port is disabled or connection is not established

Solid on

1000Mbps connection is established

Flashes

Data transfer is in progress

Delivery Package

ESR-10 standard delivery package includes:

  • ESR-10 router;
  • 220 VAC/12 VDC, 1.5 A power adapter;
  • Conformity certificate;
  • Documentation (optional);
  • Informational leaflet.

ESR-12V standard delivery package includes:

  • ESR-12V router;
  • Power cable;
  • 19” rack mounting kit;
  • Conformity certificate;
  • Documentation (optional);
  • Informational leaflet.

ESR-12VF standard delivery package includes:

  • ESR-12VF router;
  • Power cable;
  • 19” rack mounting kit;
  • Conformity certificate;
  • Documentation (optional);
  • Informational leaflet.

ESR-14VF standard delivery package includes:

  • ESR-14VF router;
  • Power cable;
  • 19” rack mounting kit;
  • Conformity certificate;
  • Documentation (optional);
  • Informational leaflet.

ESR-20 standard delivery package includes:

  • ESR-20 router;
  • Power cable;
  • 19” rack mounting kit;
  • Conformity certificate;
  • Documentation (optional);
  • Informational leaflet.

ESR-21 standard delivery package includes:

  • ESR-21 router;
  • Power cable;
  • 19” rack mounting kit;
  • Conformity certificate;
  • Documentation (optional);
  • Informational leaflet.

ESR-100 standard delivery package includes:

  • ESR-100 router;
  • Power cable;
  • 19” rack mounting kit;
  • Conformity certificate;
  • Documentation (optional);
  • Informational leaflet.

ESR-200 standard delivery package includes:

  • ESR-200 router;
  • Power cable;
  • 19” rack mounting kit;
  • Conformity certificate;
  • Documentation (optional);
  • Informational leaflet.

ESR-1000 standard delivery package includes:

  • ESR-1000 router;
  • 19” rack mounting kit;
  • Conformity certificate;
  • Documentation (optional);
  • Informational leaflet.

ESR-1200 standard delivery package includes:

  • ESR-1200 router;
  • 19” rack mounting kit;
  • Conformity certificate;
  • Documentation (optional);
  • Informational leaflet.

ESR-1500 standard delivery package includes:

  • ESR-1500 router;
  • 19” rack mounting kit;
  • Conformity certificate;
  • Documentation (optional);
  • Informational leaflet.

ESR-1511 standard delivery package includes:

  • ESR-1511 router;
  • 19” rack mounting kit;
  • Conformity certificate;
  • Documentation (optional);
  • Informational leaflet.

ESR-3100 standard delivery package includes:

  • ESR-3100 router;
  • 19” rack mounting kit;
  • Conformity certificate;
  • Documentation (optional);
  • Informational leaflet.

ESR-1700 standard delivery package includes:

  • ESR-1700 router;
  • 19” rack mounting kit;
  • Conformity certificate;
  • Documentation (optional);
  • Informational leaflet.

Power module (PM-160-220/12 or PM-100-48/12) may be included in the ESR-1000, ESR-1200 delivery package on the customer's request.

Power module (PM-160-220/12) may be included in the ESR-1500, ESR-1511, ESR-3100 delivery package on the customer's request.

Power module (PM-350-220/12 or PM-350-48/12) may be included in the ESR-1700 delivery package on the customer's request.

SFP/SFP+ transceivers may be included in the delivery package on the customer's request.