...
Примечание |
---|
При настройки MTU на туннеле необходимо учитывать следующее:
Ниже представлена примерная структура пакета: |
...
Блок кода |
---|
* Конфигурация туннеля* ESR2# sh tunnels configuration gre 1 State: Enabled Description: -- Mode: ip Bridge group: -- VRF: -- Local address: 192.0.2.2 Remote address: 192.0.2.1 Calculates checksums for outgoing GRE packets: No Requires that all input GRE packets were checksum: No key: 60 TTL: 64 DSCP: Inherit MTU: 1458 Path MTU discovery: Enabled Don't fragment bit suppression: Disabled Security zone: -- Multipoint mode: Disabled Keepalive: State: Disabled Timeout: 10 Retries: 6 Destination address: -- *Статус cервиса и выделенные метки* sh mpls l2vpn p2p P2P: EoMPLS gigabitethernet 1/0/2: MTU: 1500 Status: Up PW ID 100, Neighbor 10.100.0.1: MTU: 1500 Status TLV: Enable Last change: 00:14:27 Status: Up ESR2# sh mpls forwarding-table Local Outgoing Prefix Outgoing Next Hop label label or tunnel ID Interface -------- -------- ------------------------------------------- ---------------- --------------------------------------- 17 imp-null 10.100.0.1/32 gre 1 10.0.0.1 16 16 PW ID 100 -- 10.100.0.1 *Доступность*CE1# ping 10.100.0.2 detailed PING 10.100.0.2 (10.100.0.2) 56 bytes of data. 64 bytes from 10.100.0.2: icmp_seq=1 ttl=0 time=1.38 ms 64 bytes from 10.100.0.2: icmp_seq=2 ttl=0 time=1.22 ms 64 bytes from 10.100.0.2: icmp_seq=3 ttl=0 time=1.33 ms 64 bytes from 10.100.0.2: icmp_seq=4 ttl=0 time=1.26 ms 64 bytes from 10.100.0.2: icmp_seq=5 ttl=0 time=1.17 ms |
L3VPN
Примечание |
---|
При настройки MTU на туннеле необходимо учитывать следующее:
Ниже представлена примерная структура пакета: |
Настройки CE1 и CE2:
Блок кода | ||
---|---|---|
| ||
CE1(config)# hostname CE1
CE1(config)#
CE1(config)# route-map BGP_OUT
CE1(config-route-map)# rule 1
CE1(config-route-map-rule)# exit
CE1(config-route-map)# exit
CE1(config)# router bgp 65501
CE1(config-bgp)# neighbor 10.10.0.2
CE1(config-bgp-neighbor)# remote-as 65500
CE1(config-bgp-neighbor)# address-family ipv4 unicast
CE1(config-bgp-neighbor-af)# route-map BGP_OUT out
CE1(config-bgp-neighbor-af)# enable
CE1(config-bgp-neighbor-af)# exit
CE1(config-bgp-neighbor)# enable
CE1(config-bgp-neighbor)# exit
CE1(config-bgp)# address-family ipv4 unicast
CE1(config-bgp-af)# network 10.100.0.0/24
CE1(config-bgp-af)# exit
CE1(config-bgp)# enable
CE1(config-bgp)# exit
CE1(config)#
CE1(config)#
CE1(config)# interface gigabitethernet 1/0/2
CE1(config-if-gi)# description "to ESR1"
CE1(config-if-gi)# ip firewall disable
CE1(config-if-gi)# ip address 10.10.0.1/30
CE1(config-if-gi)# exit
CE1(config)# interface loopback 1
CE1(config-loopback)# ip address 10.100.0.1/24
CE1(config-loopback)# exit |
Блок кода | ||
---|---|---|
| ||