EN WLC
Дерево страниц

Сравнение версий

Старая версия 2

changes.mady.by.user Отдел Документации

Сохранено

по сравнению с

Новая версия 3

changes.mady.by.user Отдел Документации

Сохранено

Ключ

  • Эта строка добавлена.
  • Эта строка удалена.
  • Изменено форматирование.

...

Table 4 – Third-layer functions description (OSI Layer 3)

Static IP routes

Administrator of the router can add or remove static entries into/from the routing table.

Dynamic routing

 

With dynamic routing protocols, the device will be able to exchange the routing information with neighbouring routers and automatically create a routing table.

Router supports the following protocols: RIPv2, RIPng, OSPFv2, OSPFv3, IS-IS, BGP.

ARP table

ARP (Address Resolution Protocol) is a protocol used for resolution of the network and data-link layer addresses. ARP table contains information on the established correspondence.

Correspondence is established on the basis of the network device response analysis; device addresses are requested with broadcast packets.

DHCP client 

 

DHCP (Dynamic Host Configuration Protocol) protocol enables automation of the network device management process.

DHCP client allows the router to obtain the network address and additional settings from the external DHCP server. As a rule, this method is used for obtaining network settings of a public network operator (WAN).

DHCP server

DHCP server enables automation and centralization of the network device configuration process.

DHCP server allocated on a router allows for a complete solution for the local area network support.

DHCP server integrated into the router assigns IP addresses to network devices and transfers additional network settings, e.g. server addresses, network gateway addresses and other necessary settings.

DHCP Relay

The DHCP Relay functionality is designed to redirect broadcast DHCP Discover packets from one broadcast domain to unicast DHCP Discover packets in another broadcast domain.

NAT, Network Address Translation

Network address translation is a mechanism that translates IP addresses and port numbers for transit packets.

NAT function allows to minimize the quantity of IP address used through translation of multiple internal network IP addresses into a single external public IP address. NAT conceals local area network internal structure and allows to enhance its security.

Routers support the following NAT options:

  • Source NAT (SNAT) – the network address and the source port number will be replaced, when packet is transferred forth, and the destination address will be replaced in the response packet;
  • Destination NAT (DNAT) – external access is translated by the router to the user computer in LAN that has an internal address and thus directly inaccessible from outside the network (without NAT).

Scroll Pagebreak

Traffic tunneling functions

Table 5 – Traffic tunneling functions

Tunneling protocols

Tunneling is a method of packet conversion during their network transfer that involves the replacement, modification and addition of a new packet network header. This method may be used for negotiation of transport protocols when the data is transferred through the transit network as well as for creation of secured connections where tunneled data is being encrypted.

Routers support the following types of tunnels:

  • GRE – IP packet/Ethernet frame is encapsulated into another IP packet with GRE (General Routing Encapsulation) header;
  • IPv4-IPv4 – tunnel that encapsulates source IP packets into IP packets with alternative network parameters;
  • L2TPv3 – tunnel for L2 traffic transmission using IP packets;
  • IPsec – tunnel with the encryption of transmitted data;
  • L2TP, PPTP, PPPoE, OpenVPN – tunnels used for establishing a remote 'client-sever' access.

Management and configuration functions

Table 6 – Basic management and configuration functions

Configuration file download and upload

Device parameters are saved into the configuration file that contains configuration data for the specific device ports as well as for the whole system. The following protocols may be used for file transfers: TFTP, FTP, and SCP.

Command line interface (CLI)

CLI management is performed locally via serial port RS-232, or remotely via Telnet, SSH. Console command line interface (CLI) is the industrial standard. CLI interpreter contains the list of commands and keywords that will help the user and reduce the amount of input data.

Syslog

Syslog protocol is designed for transmission of system event messages and event logging.

Ping, traceroute
network utilities

Ping and traceroute utilities allow you to check the availability of network devices and identify data transfer routes in IP networks.

Controlled access management – privilege levels

Routers support system access level management for users. Access levels enable responsibility areas management for device administrators. Access levels are numbered from 1 to 15; Level 15 stands for full access to device management features.

Authentication

Authentication is a user identity check procedure. Routers support the following authentication methods:

  • local – local user database stored on the device is used for authentication;
  • group – user database is located on the authentication server. RADIUS and TACACS protocols are user for server interactions.

SSH Server/
Telnet Server

SSH and Telnet server features allow you to establish connection to the device and perform device management.

Automatic configuration restore

Device features automatic configuration restore system designed to prevent remote access loss after re-configuration. If the configuration change is not confirmed in the specified time, configuration will be rolled back to the last known state.

Network security functions

...

Table 7 – Network security functions

Security zones

All router interfaces are distributed by security areas.

For each zone pair, you can set the rules that determine the possibility of data transmission between zones, data traffic filtering rules.

Data filtering

For each zone pair, you can specify the rule set that manages the filtering process for data transmitted through the router.

Device command interface provides appropriate means for detailed configuration of the traffic classification rules and to apply the resulting solution for traffic transmission.

Scroll Pagebreak

Main specifications

...

Table 8 – Main specifications

General parameters

Interfaces



























WLC-15

4 × Ethernet 10/100/1000BASE-T

2 × 1000BASE-X (SFP)

1 × Console port RJ-45

1 × USB 2.0

1 × HDD slot

WLC-30

4 × Ethernet 10/100/1000BASE-T

2 × 10GBASE-R (SFP+)/1000BASE-X

1 × Console port RJ-45

1 × USB 3.0

1 × USB 2.0

1 × HDD slot

1 × microSD card slot

WLC-3200

12 × 1000BASE-X/10GBASE-R/25GBASE-R

1 × Console RS-232 (RJ-45)

1 × OOB port

1 × USB 2.0

1 × microSD card slot

ESR-3200

12 × 1000BASE-X/10GBASE-R/25GBASE-R

1 × Console RS-232 (RJ-45)

1 × OOB port

1 × USB 2.0

1 × microSD card slot

ESR-3100

8 × Combo Ethernet 10/100/1000BASE-T/1000BASE-X 

8 × 10GBASE-R/1000BASE-X (SFP+/SFP)

1 × Console RS-232 (RJ-45)

2 × USB 3.0

1 × SD card slot

ESR-1700

4 × Combo Ethernet 10/100/1000BASE-T/1000BASE-X

8 × 10GBASE-R/1000BASE-X (SFP+/SFP)

2 × Hard disk installation slot

1 × Console RS-232 (RJ-45)

1 × OOB port

2 × USB 2.0

ESR-1511

4 × Combo Ethernet 10/100/1000BASE-T/1000BASE-X 

4 × Ethernet 10/100/1000BASE-T (RJ-45)

4 × 10GBASE-R/1000BASE-X (SFP+/SFP)

2 × 40GBASE-X (QSFP+) 

1 × Console RS-232 (RJ-45)

1 × OOB port

2 × USB 2.0

1 × SD card slot

ESR-1500

4 × Combo Ethernet 10/100/1000BASE-T/1000BASE-X 

4 × Ethernet 10/100/1000BASE-T (RJ-45)

4 × 10GBASE-R/1000BASE-X (SFP+/SFP)

1 × Console RS-232 (RJ-45)

1 × OOB port

2 × USB 2.0

1 × SD card slot

ESR-1200

4 × Combo Ethernet 10/100/1000BASE-T/1000BASE-X 

12 × Ethernet 10/100/1000BASE-T (RJ-45)

8 × 10GBASE-R/1000BASE-X (SFP+/SFP)

1 × Console RS-232 (RJ-45)

2 × USB 2.0

1 × SD card slot

ESR-1000

24 × Ethernet 10/100/1000BASE-T (RJ-45)

2 × 10GBASE-R/1000BASE-X (SFP+/SFP)

1 × Console RS-232 (RJ-45)

2 × USB 2.0

1 × SD card slot

ESR-200

4 × Combo Ethernet 10/100/1000BASE-T/1000BASE-X 

4 × Ethernet 10/100/1000BASE-T (RJ-45)

1 × Console RJ-45

1 × USB 3.0

1 × USB 2.0

1 × SD card slot

ESR-100

4 × Combo Ethernet 10/100/1000BASE-T/1000BASE-X 

1 × Console RS-232 (RJ-45)

1 × USB 3.0

1 × USB 2.0

1 × SD card slot

ESR-30

4 × Ethernet 10/100/1000BASE-T (RJ-45)

2 × 10GBASE-R/1000BASE-X (SFP+/SFP)

1 × Console RS-232 (RJ-45)

1 × USB 3.0

1 × USB 2.0

1 × microSD card slot

ESR-21

8 × Ethernet 10/100/1000BASE-T (RJ-45)

4 × 1000BASE-X (SFP)

3 × Serial port RS-232

1 × Console RS-232 (RJ-45)

1 × USB 3.0

1 × USB 2.0

1 × SD card slot

ESR-20

2 × Combo Ethernet 10/100/1000BASE-T/1000BASE-X 

2 × Ethernet 10/100/1000BASE-T (RJ-45)

1 × Console RS-232 (RJ-45)

1 × USB 3.0

1 × USB 2.0

1 × SD card slot

ESR-15

4 × Ethernet 10/100/1000BASE-T (RJ-45)

2 × 1000BASE-X (SFP)

1 × Console RS-232 (RJ-45)

2 × USB 2.0

ESR-14VF

8 × Ethernet 10/100/1000BASE-T (RJ-45)

1 × 1000BASE-X (SFP)

1 × Console RS-232 (RJ-45)

4 × FXS

2 × USB 2.0

ESR-12VF

8 × Ethernet 10/100/1000BASE-T (RJ-45)

1 × 1000BASE-X (SFP)

1 × Console RS-232 (RJ-45)

3 × FXS

1 × FXO

2 × USB 2.0

ESR-12V

8 × Ethernet 10/100/1000BASE-T (RJ-45)

1 × Console RS-232 (RJ-45)

3 × FXS

1 × FXO

2 × USB 2.0

ESR-10

4 × Ethernet 10/100/1000BASE-T (RJ-45)

2 × 1000BASE-X (SFP)

1 × Console RS-232 (RJ-45)

2 × USB 2.0

Types of optical transceivers

WLC-15

1000BASE-X SFP

WLC-30

1000BASE-X SFP

10GBASE-R SFP+

WLC-3200

1000BASE-X SFP

10GBASE-R SFP+

25GBASE-R SFP28

ESR-3200

1000BASE-X SFP

10GBASE-R SFP+

25GBASE-R SFP28

ESR-1511

1000BASE-X SFP

10GBASE-R SFP+

40GBASE-X QSFP+

ESR-1700

ESR-3100

ESR-1500

ESR-1200

ESR-1000

ESR-30

1000BASE-X SFP

10GBASE-R SFP+

ESR-200

ESR-100

ESR-21

ESR-20

ESR-15

ESR-14VF

ESR-12VF

ESR-10

1000BASE-X SFP

ESR-151000BASE-R SFP+

Duplex or half-duplex interface modes

  • duplex and half-duplex modes for electric ports
  • duplex mode for optical ports

Maximum bandwidth in
L2 mode (hardware switching)

ESR-1700

ESR-1511

ESR-1500

ESR-1200

160 Gbps

ESR-1000

88 Gbps

Data transfer rate

WLC-15

  • electrical interfaces 10/100/1000Mbps
  • optical interfaces 1 Gbps
WLC-30
  • electrical interfaces 10/100/1000Mbps
  • optical interfaces 1/10 Gbps

WLC-3200

ESR-3200

  • optical interfaces 1/10/25 Gbps
ESR-1511
  • electrical interfaces 10/100/1000Mbps
  • optical interfaces 1/10/40 Gbps

ESR-3100

ESR-1700

ESR-1500

ESR-1200

ESR-1000

  • electrical interfaces 10/100/1000Mbps
  • optical interfaces 1/10Gbps

ESR-200

ESR-100

ESR-21

ESR-20

ESR-15

ESR-14VF

ESR-12V(F)

ESR-10

  • electrical interfaces 10/100/1000Mbps
  • optical interfaces 1Gbps

Number of VPN tunnels


WLC-3200

ESR-3200

ESR-3100

ESR-1700

ESR-1511

ESR-1500

ESR-1200

ESR-1000

500

WLC-30

ESR-200

ESR-100

ESR-30

ESR-21

ESR-20

250

WLC-15

ESR-15

ESR-14VF

ESR-12V(F)

ESR-10

10

Number of static routes

WLC-30

WLC-3200

ESR-3200

ESR-3100

ESR-1700

ESR-1511

ESR-1500

ESR-1200

ESR-1000

ESR-200

ESR-100

ESR-30

ESR-21

ESR-20

11k

WLC-15

ESR-15

ESR-14VF

ESR-12V(F)

ESR-10

1k

Number of concurrent sessions

WLC-3200

ESR-3200

ESR-3100

ESR-1700

ESR-1511

ESR-1500

ESR-1200

ESR-1000

512k

WLC-30

ESR-200

ESR-100

ESR-30

ESR-21

ESR-20

256k

ESR-15

ESR-14VF

ESR-12V(F)

ESR-10

4k

VLAN support

up to 4k active VLANs according to 802.1Q

Number of BGPv4/BGPv6 routes

WLC-3200

ESR-3200

ESR-3100

ESR-1700

ESR-1511

ESR-1500

ESR-1200

ESR-1000

5M

WLC-30

ESR-200

ESR-100

ESR-30

ESR-21

ESR-20

2.5M

WLC-15

ESR-15

ESR-14VF

ESR-12V(F)

ESR-10

1M

Number of OSPFv2/OSPFv3/IS-IS routes

WLC-3200

ESR-3200

ESR-3100

ESR-1700

ESR-1511

ESR-1500

ESR-1200

ESR-1000

500k

WLC-30

ESR-200

ESR-100

300k

WLC-15

ESR-30

ESR-21

ESR-20

ESR-15

ESR-14VF

ESR-12V(F)

ESR-10

30k

Number of RIP/RIPng routes

WLC-30

WLC-3200

ESR-3200

ESR-3100

ESR-1700

ESR-1511

ESR-1500

ESR-1200

ESR-1000

ESR-200

ESR-100

ESR-30

ESR-21

ESR-20

10k

WLC-15

ESR-15

ESR-14VF

ESR-12V(F)

ESR-10

1k

MAC address table


ESR-1700

ESR-1511

ESR-1500

ESR-1200

128k entries

WLC-3200

ESR-3200

ESR-1000

16k entries

WLC-15

WLC-30

ESR-3100

ESR-200

ESR-100

ESR-30

ESR-21

ESR-20

ESR-15

ESR-14VF

ESR-12V(F)

ESR-10

2k bridge entries

FIB size





ESR-1700

3.0M

WLC-3200

ESR-3200

ESR-3100

ESR-1511

ESR-1500

ESR-1200

ESR-1000

1.7M

WLC-30

ESR-200

ESR-100

ESR-30

ESR-21

ESR-20

1.4M

WLC-151M

ESR-15

ESR-14VF

ESR-12V(F)

ESR-10

800k

VRF Lite

32

L3 interfaces

WLC-30

WLC-3200

ESR-3200

ESR-3100

ESR-1700

ESR-1500

ESR-1511

ESR-1200

ESR-1000

ESR-200

ESR-100

ESR-30

ESR-21

ESR-20

4000

WLC-15

ESR-15

ESR-14VF

ESR-12V(F)

ESR-10

200

Compliance

IEEE 802.3 10BASE-T Ethernet

IEEE 802.3u 100BASE-T Fast Ethernet

IEEE 802.3ab 1000BASE-T Gigabit Ethernet

IEEE 802.3z Fiber Gigabit Ethernet

IEEE 802.3ba 40GBASE-SR4, 40GBASE-LR4

ANSI/IEEE 802.3 Speed autodetection

IEEE 802.3x Data flow control

IEEE 802.3ad LACP link aggregation

IEEE 802.1q VLAN virtual local networks

IEEE 802.1v

IEEE 802.3ac

IEEE 802.3ae

IEEE 802.1D

IEEE 802.1w

IEEE 802.1s

Control

Local control

CLI

Remote control

TELNET, SSH

Physical specifications and ambient conditions

Power supply

ESR-1700

AC: 176–264 V, 50–60 Hz

DC: 36–72 V

Power options:

  • single AC or DC power supply;
  • two AC or DC power supplies with hot swapping.


WLC-3200

ESR-3200

ESR-3100

ESR-1511

ESR-1500

ESR-1200

ESR-1000

AC: 100–240 V, 50–60 Hz

DC: 36–72 V

Power options:

  • single AC or DC power supply;
  • two AC or DC power supplies with hot swapping.

WLC-15

WLC-30

ESR-200

ESR-100

ESR-30

ESR-21

ESR-20

ESR-14VF

ESR-12V(F)

AC: 100–264 V, 50–60 Hz

ESR-15220 V/12 V, 2 A DC power adapter

ESR-10

220 V/12 V, 1.5 A DC power adapter

Maximum power consumption:


WLC-3200

ESR-3200

118 W

ESR-3100123 W

ESR-1700

 250 W

ESR-1511

128 W

ESR-1500

125 W

ESR-1200

85 W

ESR-1000

75 W

ESR-200

25 W

ESR-100

20 W

WLC-30

ESR-30

26 W

ESR-21

32 W

ESR-20

25 W

WLC-15

ESR-15

18 W

ESR-14VF

ESR-12V(F)

22 W

ESR-10

9 W

Weight



WLC-15

2.7 kg

WLC-302.934 kg
WLC-32006.08 kg
ESR-32005 kg

ESR-3100

4.34 kg

ESR-170012 kg

ESR-1511

ESR-1500

7 kg

ESR-1200

5.5 kg

ESR-1000

3.6 kg

ESR-200

ESR-100

2.5 kg

ESR-301.8 kg

ESR-21

3.15 kg

ESR-20

2 kg

ESR-150.325 kg

ESR-14VF

ESR-12V(F)

ESR-10

1 kg

Dimensions (W × H × D)




WLC-15

430 × 44 × 226 mm

WLC-30430 × 44 × 225 mm
WLC-3200430 × 44 × 330 mm

ESR-3200

ESR-3100

430 × 44 × 330 mm
ESR-1700 440 × 88 × 490 mm

ESR-1511

ESR-1500

430 × 44 × 425 mm

ESR-1200

ESR-1000

430 × 44 × 352 mm

ESR-200

ESR-100

310 × 44 × 240 mm

ESR-21

430 × 44 × 225 mm

ESR-30

ESR-20

267 × 44 × 212 mm

ESR-15230 × 32 × 133 mm

ESR-14VF

ESR-12V(F)

267 × 43.6 × 160.5 mm

ESR-10

185 × 32 × 118 mm

Operating temperature range

WLC-30

WLC-3200

ESR-3200

ESR-3100

ESR-1700

ESR-1511

ESR-1500

ESR-1200

ESR-1000

ESR-200

ESR-100

ESR-30

ESR-21

ESR-20

-10 to +45 °C

WLC-15

ESR-15

ESR-14VF

ESR-12V(F)

ESR-10

0 to +40 °C

Storage temperature range

-40 to +70 °C

Operation relative humidity (non-condensing)

up to 80 %

Storage relative humidity (non-condensing)

from 10 to 95 %

Lifetime

at least 15 years

Scroll Pagebreak

Design

This section describes the design of the device. Depicted front, rear, and side panels of the device, connectors, LED indicators and controls.

...

Table 9 – Description of connectors, LEDs and controls located on WLC-15

№

Front panel element

Description

1

110-250 V АC 50–60 Hz

Источник питания

Power source.

2

Power

Индикатор питания устройства

Device power LED.

Status

Индикатор текущего состояния устройства

Current device status LED.

Alarm

Индикатор наличия и уровня аварии устройства

Alarm LED.

User

Индикатор, использущийся для пользовательских сценариев, которые можно назначить в режиме конфигурирования устройства.

3

Console

Консольный порт
Console port RS-232 (RJ-45)
для локального управления устройством
for local management of the device.
4F

Функциональная кнопка для перезагрузки устройства и сброса к заводским настройкам:

  • при удержании кнопки менее 10 секунд происходит перезагрузка устройства;
    • при удержании кнопки более 10 секунд происходит перезагрузка устройства и сброс к заводским настройкам

    Functional key that reboots the device and resets it to factory default configuration:

    • Pressing the key for less than 10 seconds reboots the device;
    • Pressing the key for more than 10 seconds resets the terminal to factory settings.

    5

    USB

    Разъем USB 2.0 для подключения внешних USB-устройств.

    6

    [1 .. 4]

    4

    порта

    ports of Ethernet 10/100/1000BASE-T.

    7

    [5-6]

    2

    порта

    ports of 1000BASE-X SFP. 

    8HDD
    Разъем для установки жесткого диска памяти. 
    Connector for HDD installation.

    WLC-15 rear panel

    Внешний вид задней панели устройства The rear panel of WLC-15 приведен на рисунке нижеis depicted in figure below.

    Figure 2 – WLC-15 rear panel

    Table 10 – Описание разъемов задней панели контроллера WLCWLC-15 rear panel connectors description

    №

    Description

    1

    Клемма для заземления устройства

    Earth bonding point of the device.

    WLC-15 side panels

    Внешний вид боковых панелей устройства The side panel layout of WLC-15 приведен на рисунках нижеis depicted in figures below.

    Figure 3 – WLC-15 right side panel

    ...

    Figure 4 – WLC-15 left side panel

    На боковых панелях устройства расположены вентиляционные решетки, которые служат для отвода тепла. Не закрывайте вентиляционные отверстия посторонними предметами. Это может привести к перегреву компонентов устройства и вызвать нарушения в его работе. Рекомендации по установке устройства расположены в разделе Установка и подключениеSide panels of the device have air vents for heat removal. Do not block air vents. This may cause the components to overheat, which may result in device malfunction. For recommendations on device installation, see section Installation and connection.

    WLC-30 design

    WLC-30 front panel

    Внешний вид передней панели показан на рисунке 5The front panel layout is depicted below.

    Figure 5 – WLC-30 front panel

    Table 11 – Описание разъемов, индикаторов и органов управления передней панели WLC-30– Description of connectors, LEDs and controls located on WLC-30 front panel

    №

    Front panel element

    Description

    1

    110-250 V АC 50–60 Hz

    Источник питания

    Power source.

    2

    Power

    Индикатор питания устройства

    Device power LED.

    Status

    Индикатор текущего состояния устройства

    Current device status LED.

    Alarm

    Индикатор наличия и уровня аварии устройства

    Alarm LED.

    User

    Индикатор, использущийся для пользовательских сценариев, которые можно назначить в режиме конфигурирования устройства.

    3

    F

    Функциональная кнопка для перезагрузки устройства и сброса к заводским настройкам:

  • при удержании кнопки менее 10 секунд происходит перезагрузка устройства;
    • при удержании кнопки более 10 секунд происходит перезагрузка устройства и сброс к заводским настройкам

    Functional key that reboots the device and resets it to factory default configuration:

    • Pressing the key for less than 10 seconds reboots the device;
    • Pressing the key for more than 10 seconds resets the terminal to factory settings.

    4

    Console

    Консольный порт

    Console port RS-232 (RJ-45)

    для локального управления устройством

    for local management of the device.

    5

    microSD

    Разъем для установки

    microSD-

    карт памяти

    card port.

    6

    USB1

    Разъем

    USB 2.0

    для подключения внешних USB-устройств

    port for USB devices connection.

    7

    USB2

    Разъем

    USB 3.0

    для подключения внешних USB-устройств

    port for USB devices connection.

    8

    [1 .. 4]

    4

    порта

    ports of Ethernet 10/100/1000BASE-T.

    9

    XG1, XG2

    2

    порта

    ports of 10GBASE-R (SFP+)1000BASE-X.

    10HDD
    Разъем для установки жесткого диска памяти
    Connector for HDD installation.

    WLC-30 rear panel

    Внешний вид задней панели устройства The rear panel of WLC-30 приведен на рисунке нижеis depicted in below.

    Figure 6 – WLC-30 rear panel

    Table 12 – Описание разъемов задней панели контроллера WLCWLC-30 rear panel connectors description

    №

    Description

    1

    Клемма для заземления устройства

    Earth bonding point of the device.

    WLC-30 side panels

    Внешний вид боковых панелей устройства The side panel layout of WLC-30 приведен на рисунках нижеis depicted in figures below.


    Figure 7 – WLC-30 right side panel

    ...

    Figure 8 – WLC-30 left side panel

    На боковых панелях устройства расположены вентиляционные решетки, которые служат для отвода тепла. Не закрывайте вентиляционные отверстия посторонними предметами. Это может привести к перегреву компонентов устройства и вызвать нарушения в его работе. Рекомендации по установке устройства расположены в разделе Установка и подключениеSide panels of the device have air vents for heat removal. Do not block air vents. This may cause the components to overheat, which may result in device malfunction. For recommendations on device installation, see section Installation and connection.

    WLC-3200 design

    WLC-3200 front panel

    Внешний вид передней панели показан на рисунке 9The front panel layout is depicted below.

    Figure 9 – WLC-3200 front panel

    Table 13 – Описание разъемов, индикаторов и органов управления передней панели WLC-3200 Description of connectors, LEDs and controls located on WLC-3200 front panel

    №

    Front panel element

    Description

    1






    Status

    Индикатор текущего состояния устройства

    Current device status LED.

    Alarm

    Индикатор наличия и уровня аварии устройства

    Alarm LED.

    UserИндикатор, использущийся для пользовательских сценариев, которые можно назначить в режиме конфигурирования устройства.
    Flash
    Индикатор активности обмена с накопителем данных – microSD-картой или
    Activity of exchange with data storage – microSD card or USB Flash.

    Power

    Индикатор питания устройства

    Device power LED.

    Master

    Индикатор работы устройства в failover-режимах (не используется в текущей версии

    Failover mode operation LED (is not supported in the current version).

    Fan

    Индикатор аварии вентиляторов

    Fan operation LED.

    RPS

    Индикатор резервного источника электропитания

    Redundant power supply LED.

    2

    F

    Функциональная кнопка для перезагрузки устройства и сброса к заводским настройкам:

  • при удержании кнопки менее 10 секунд происходит перезагрузка устройства;
    • при удержании кнопки более 10 секунд происходит перезагрузка устройства и сброс к заводским настройкам

    Functional key that reboots the device and resets it to factory default configuration:

    • Pressing the key for less than 10 seconds reboots the device;
    • Pressing the key for more than 10 seconds resets the terminal to factory settings.
    3OOB

    Ethernet-порт используется только для обновления программного обеспечения через загрузчик U-Boot. Данный порт не используется для удаленного доступа и управления.

    Console
    Консольный порт
    Console port RS-232 (RJ-45)
    для локального управления устройством
    for local management of the device.

    4

    microSD

    Разъем для установки

    microSD-

    карт памяти

    card port.

    5USB
    Порт
    USB 2.0
    для подключения USB-устройств
    port for USB devices connection.
    6

    [1 .. 12]

    Слоты для установки трансиверов
    Slots for 25G SFP28/10G SFP+/1G SFP transceivers.
    7HDD
    Разъем для установки жесткого диска памяти
    Connector for HDD installation.

    WLC-3200 rear panel

    Внешний вид задней панели устройства The rear panel of WLC-3200 приведен на рисунке нижеis shown in the picture below.

    Figure 10 – WLC-3200 rear panel

    Table 14 – Описание разъемов задней панели контроллера WLCWLC-3200 rear panel connectors description

    №

    Description

    1

    Основной источник питания

    Main power supply.

    2

    Клемма для заземления устройства

    Earth bonding point of the device.

    3

    Съемные вентиляционные модули с возможностью горячей замены

    Hot-swappable removable ventilation modules.

    4

    Место для установки резервного источника питания

    Place for installation of a redundant power supply.

    WLC-3200 side panels

    Внешний вид боковых панелей устройства The side panel layout of WLC-3200 приведен на рисунках нижеis depicted in figures below.

    Figure 11 – WLC-3200 right side panel

    ...

    Figure 12 – WLC-3200 left side panel

    На боковых панелях устройства расположены вентиляционные решетки, которые служат для отвода тепла. Не закрывайте вентиляционные отверстия посторонними предметами. Это может привести к перегреву компонентов устройства и вызвать нарушения в его работе. Рекомендации по установке устройства расположены в разделе Установка и подключениеSide panels of the device have air vents for heat removal. Do not block air vents. This may cause the components to overheat, which may result in device malfunction. For recommendations on device installation, see section Installation and connection.

    ESR-3200 design

    ESR-3200 front panel

    The front panel layout is depicted in Figure 1figure below.

    Figure 1 13 – ESR-3200 front panel

    Table 9 lists connectors, LEDs and controls located on the front panel of ESR-3100.

    Table 9 – Description of connectors, LEDs and controls located on ESR-3100 front panel

    №

    Front panel element

    Description

    1

    Status

    Current device status LED.

    Alarm

    Alarm LED.

    VPN

    VPN gateway operation mode LED.

    Flash

    Activity of exchange with data storage – SD card or USB Flash.

    Power

    Device power LED.

    Master

    Failover mode operation LED (is not supported in the current version).

    Fan

    Fan operation LED.

    RPS

    Redundant power supply LED.

    2

    F

    Functional key that reboots the device and resets it to factory default configuration:

    • Pressing the key for less than 10 seconds reboots the device;
    • Pressing the key for more than 10 seconds resets the terminal to factory settings.
    3OOBEthernet port for router management.

    4

    Console

    Console port RS-232 (RJ-45) for local management of the device.

    5

    microSD

    microSD-card port.

    6

    USB1

    USB 2.0 port for USB devices connection.

    7

    [1 .. 12]

    Slots for installing 25G SFP28/10G SFP+/1G SFP transceivers.

    ESR-3200 rear panel

    The rear panel of ESR-3200 is depicted in Figure 2figure below.

    Figure 2 14 – ESR-3200 rear panel

    Table 10 lists rear panel connectors of the router.

    Table 10 – Rear panel connectors description

    №

    Description

    1

    Main power supply.

    2

    Earth bonding point of the device.

    3

    Hot-swappable removable ventilation modules.

    4

    5

    Place for installation of a redundant power supply.

    Scroll Pagebreak

    ESR-3200 side panels

    The side panel layout of ESR-3200 is depicted in figures 3 and 4below.

    Figure 3 15 – ESR-3200 right side panel

    Figure 4 16 – ESR-3200 left side panel

    ...

    The front panel layout is depicted in 5figure below.

    Figure 5 17 – ESR-3100 front panel

    Table 11 lists connectors, LEDs and controls located on the front panel of ESR-3100.

    Table 11 – Description of connectors, LEDs and controls located on ESR-3100 front panel

    №

    Front panel element

    Description

    1

    Status

    Current device status LED.

    Alarm

    Alarm LED.

    VPN

    VPN gateway operation mode LED.

    Flash

    Activity of exchange with data storage – SD card or USB Flash.

    Power

    Device power LED.

    Master

    Failover mode operation LED (is not supported in the current version).

    Fan

    Fan operation LED.

    RPS

    Redundant power supply LED.

    2

    F

    Functional key that reboots the device and resets it to factory default configuration:

    • Pressing the key for less than 10 seconds reboots the device;
    • Pressing the key for more than 10 seconds resets the terminal to factory settings.

    3

    Console

    Console port RS-232 (RJ-45) for local management of the device.

    4

    SD

    SD-card connector.

    5

    USB1

    USB 3.0 port for USB device connection.

    6

    USB2

    USB 3.0 port for USB device connection.

    7

    [1 .. 8]

    8 ports of Gigabit Ethernet 10/100/1000BASE-T (RJ-45).

    8

    XG1 – XG8

    Slots for 10G SFP+/1G SFP transceivers.

    ESR-3100 rear panel

    The rear panel of ESR-3100 is depicted in the figure below.

    Figure 6 18 – ESR-3100 rear panel

    Table 12 lists rear panel connectors of the router. 

    Scroll Pagebreak

    Table 12 – Rear panel connectors description

    №

    Description

    1

    Main power supply.

    2

    Earth bonding point of the device.

    3

    Hot-swappable removable ventilation modules.

    4

    5

    Place for installation of a redundant power supply.

    ESR-3100 side panels

    The side panel layout of ESR-3100 is depicted in figures 7 and 8below.

    Figure 7 19 – ESR-3100 right side panel

    Figure 8 20 – ESR-3100 left side panel

    ...

    The front panel layout is depicted in figure 9below.

    Figure 9 21 – ESR-1700 front panel

    Table 13 lists connectors, LEDs and controls located on the front panel of ESR-1700.

    Table 13 – Description of ESR-1700 connectors, LEDs and front panel controls

    №

    Front panel element

    Description

    1

    HDD1

    Connector for HDD installation.

    2

    HDD2

    Connector for HDD installation.

    3

    USB1

    Port for USB device connection.

    4

    USB2

    Port for USB device connection.

    5

    Combo Ports [1 .. 4]

    4 ports of Gigabit Ethernet 10/100/1000BASE-X (SFP).

    6

    XG1 – XG8

    Slots for 10G SFP+/1G SFP transceivers.

    7

    Status

    Current device status LED.

    Alarm

    Alarm LED.

    VPN

    VPN gateway operation mode LED (is not supported in the current version).

    Flash

    Activity of exchange with data storage – SD card or USB Flash.

    Power

    Device power LED.

    Master

    Failover mode operation LED (is not supported in the current version).

    Fan

    Fan operation LED.

    RPS

    Redundant power supply LED.

    8

    F

    Functional key that reboots the device and resets it to factory default configuration:

    • Pressing the key for less than 10 seconds reboots the device;
    • Pressing the key for more than 10 seconds resets the terminal to factory settings.

    9

    Console

    Console port RS-232 for local management of the device.

    10

    OOB

    Ethernet port for router management.

    Scroll Pagebreak

    ESR-1700 rear panel

    The rear panel of ESR-1700 is shown in the picture below.

    Figure 10 22 – ESR-1700 rear panel

    Table 14 lists rear panel connectors of the router.

    Table 14 – Rear panel connectors description

    №

    Description

    1

    Earth bonding point of the device.

    2

    Hot-swappable removable ventilation modules.

    3

    Main power supply.

    4

    Place for installation of a redundant power supply.

    ESR-1700 side panels

    The side panel layout of ESR-1700 is depicted in figures 3 and 4below.

    Figure 11 23 – ESR-1700 right side panel

    Figure 12 24 – ESR-1700 left side panel

    ...

    The front panel layout is depicted in figure 9below.


    Figure 13 25 – ESR-1511 front panel

    Table 15 lists connectors, LEDs and controls located on the front panel of ESR-1511.

    Table 15 – Description of connectors, LEDs and controls located on ESR-1511 front panel

    №

    Front panel element

    Description

    1

    Status

    Current device status LED.

    Alarm

    Alarm LED.

    VPN

    VPN gateway operation mode LED (is not supported in the current version).

    Flash

    Activity of exchange with data storage – SD card or USB Flash.

    Power

    Device power LED.

    Master

    Failover mode operation LED (is not supported in the current version).

    Fan

    Fan operation LED.

    RPS

    Redundant power supply LED.

    2

    Console

    Console port RS-232 for local management of the device.

    3

    OOB

    Ethernet port for router management.

    4

    SD

    SD-card connector.

    5

    USB1

    Port for USB device connection.

    6

    F

    Functional key that reboots the device and resets it to factory default configuration:

    • Pressing the key for less than 10 seconds reboots the device;
    • Pressing the key for more than 10 seconds resets the terminal to factory settings.

    7

    USB2

    Port for USB device connection.

    8

    Ethernet

    4 ports of Ethernet 10/100/1000BASE-T.

    9

    Combo Ports [1 .. 4]

    4 ports of Gigabit Ethernet 10/100/1000BASE-X (SFP).

    10

    XG1 – XG4

    Slots for 10G SFP+/1G SFP transceivers.

    11

    XLG1 – XLG2

    Slots for 40G QSFP+ transceivers.

    ESR-1500 front panel

    The front panel layout is depicted in figure 14below.


    Figure 14 26 – ESR-1500 front panel

    Table 16 lists connectors, LEDs and controls located on the front panel of ESR-1500.

    Table 16 – Description of ESR-1500 connectors, LEDs and front panel controls

    №

    Front panel element

    Description

    1

    Status

    Current device status LED.

    Alarm

    Alarm LED.

    VPN

    VPN gateway operation mode LED (is not supported in the current version).

    Flash

    Activity of exchange with data storage – SD card or USB Flash.

    Power

    Device power LED.

    Master

    Failover mode operation LED (is not supported in the current version).

    Fan

    Fan operation LED.

    RPS

    Redundant power supply LED.

    2

    Console

    Console port RS-232 for local management of the device.

    3

    OOB

    Ethernet port for router management.

    4

    SD

    SD-card connector.

    5

    USB1

    Port for USB device connection.

    6

    F

    Functional key that reboots the device and resets it to factory default configuration:

    • Pressing the key for less than 10 seconds reboots the device;
    • Pressing the key for more than 10 seconds resets the terminal to factory settings.

    7

    USB2

    Port for USB device connection.

    8

    Ethernet

    4 ports of Ethernet 10/100/1000BASE-T.

    9

    Combo Ports [1 .. 4]

    4 ports of Gigabit Ethernet 10/100/1000BASE-X (SFP).

    10

    XG1 – XG4

    Slots for 10G SFP+/1G SFP transceivers.

    Scroll Pagebreak

    ESR-1511, ESR-1500 rear panel

    The rear panel layout of ESR-1511 and ESR-1500 routers is depicted in figure 15below.

    Figure 15 27 – ESR-1511, ESR-1500 rear panel

    ...

    Table 17 – Rear panel connectors description

    №

    Description

    1

    Main power supply.

    2

    Earth bonding point of the device.

    3

    Hot-swappable removable ventilation modules.

    4

    Place for installation of a redundant power supply.

    ESR-1511, ESR-1500 side panels

    The side panel layout of ESR-1511, ESR-1500 is depicted in Figures 16 and 17figures below.

    Figure 16 28 – ESR-1511, ESR-1500 right side panel

    Figure 17 29 – ESR-1511, ESR-1500 left side panel

    ...

    The front panel layout is depicted in 18figure below.

    Figure 18 30 – ESR-1200 front panel

    Table 18 lists connectors, LEDs and controls located on the front panel of ESR-1200.

    Table 18 – Description of connectors, LEDs and controls located on the front panel of ESR-1200

    №

    Front panel element

    Description

    1

    SD

    SD-card connector.

    2

    USB1

    Port for USB device connection.

    3

    USB2

    Port for USB device connection.

    4

    [1 .. 12]

    12 ports of Gigabit Ethernet 10/100/1000BASE-T (RJ-45).

    5

    Combo Ports

    4 ports of Gigabit Ethernet 10/100/1000BASE-X (SFP).

    6

    XG1 – XG8

    Slots for installation of 10G SFP+/1G SFP transceivers.

    7

    Status

    Current device status LED.

    Alarm

    Alarm LED.

    HA

    HA operation mode LED.

    Flash

    Activity indicator of exchange with data storages (SD-card or USB Flash).

    Power

    Device power LED.

    Master

    Indicator of failover modes operation.

    Fan

    Fan operation LED.

    RPS

    Redundant power supply LED.

    8

    F

    Functional key that reboots the device and resets it to factory default configuration:

    • Pressing the key for less than 10 seconds reboots the device;
    • Pressing the key for more than 10 seconds resets the terminal to factory settings.

    9

    Console

    Console port RS-232 for local management of the device.

    ESR-1000 front panel

    The front panel layout is depicted in 19figure below.

    Figure 19 31 – ESR-1000 front panel

    Table 19 lists sizes, LEDs and controls located on ESR-1000 front panel.

    Table 19 – Description of connectors, LEDs and controls located on ESR-1000 front panel

    №

    Front panel element

    Description

    1

    SD

    SD-card connector.

    2

    USB1

    Port for USB device connection.

    3

    USB2

    Port for USB device connection.

    4

    XG1, XG2

    Slots for 10G SFP+/1G SFP transceivers.

    5

    [1 .. 24]

    24 ports of Gigabit Ethernet 10/100/1000BASE-T (RJ-45).

    6

    Status

    Current device status LED.

    Alarm

    Alarm LED.

    VPN

    Active VPN sessions indicator.

    Flash

    Activity indicator of exchange with data storages (SD-card or USB Flash).

    Power

    Device power LED.

    Master

    Indicator of failover modes operation.

    Fan

    Fan operation LED.

    RPS

    Redundant power supply LED.

    7

    F

    Functional key that reboots the device and resets it to factory default configuration:

    • Pressing the key for less than 10 seconds reboots the device;
    • Pressing the key for more than 10 seconds resets the terminal to factory settings.

    8

    Console

    Console port RS-232 for local management of the device.

    ESR-1200, 1000 rear panel

    ...

    Примечание

    The figure shows the router delivery package with a single AC power supply.

    Figure 20 32 – ESR-1000 rear panel

    Table 20 lists rear panel connectors of the router.

    Scroll Pagebreak

    Table 20 – Rear panel connectors description

    №

    Description

    1

    Main power supply.

    2

    Place for installation of a redundant power supply.

    3

    Hot-swappable removable ventilation modules.

    4

    Earth bonding point of the device.

    ESR-1200, ESR-1000 side panels

    The side panel layout of ESR-1200, ESR-1000 is depicted in Figures 21 and 22figures below.

    Figure 21 33 – ESR-1200, 1000 right side panel

    Figure 22 34 – ESR-1200, 1000 left side panel

    ...

    The front panel layout of ESR-200 is depicted in figure 23below.

    Figure 23 35 – ESR-200 front panel

    The front panel layout of ESR-100 is depicted in figure 24below.

    Figure 24 36 – ESR-100 front panel

    Table 21 lists connectors, LEDs and controls located on the front panel of ESR-100 and ESR-200 routers.

    Table 21 – Description of connectors, LEDs and controls located on ESR-200, ESR-100 front panel

    №

    Front panel element

    Description

    1

    SD

    SD-card connector.

    2

    USB1, USB2

    2 × USB-enabled devices connection port.

    3

    [1 .. 4]

    4 ports of Gigabit Ethernet 10/100/1000BASE-T (RJ-45).

    4

    Combo Ports

    4 ports of Gigabit Ethernet 10/100/1000BASE-X (SFP).

    5

    Power

    Device power LED.

    Status

    Current device status LED.

    Alarm

    Alarm LED.

    Fan

    Fan operation LED.

    6

    F

    Functional key that reboots the device and resets it to factory default configuration:

    • Pressing the key for less than 10 seconds reboots the device;
    • Pressing the key for more than 10 seconds resets the terminal to factory settings.

    7

    Console

    Console port RS-232 for local management of the device.

    8

    110-250 VAC
    60/50 Hz max 1A

    Power supply.

    Scroll Pagebreak

    ESR-200, ESR-100 rear panel

    The rear panel layout of ESR-200 and ESR-100 routers is depicted in figure 25below.

    Figure 25 37 – ESR-200, ESR-100 rear panel

    ...

    The side panel layout of ESR-200, ESR-100 is depicted in Figures 26 and 27figures below.

    Figure 26 38 – ESR-100 and ESR-200 right side panel

    Figure 27 39 – ESR-100 and ESR-200 left side panel

    ...

    The front panel layout of ESR-21 is depicted in figure 28below.

    Figure 28 40 – ESR-21 front panel

    Table 23 lists sizes, LEDs and controls located on ESR-21 front panel.

    ...

    The rear panel layout of ESR-21 is depicted in figure 29below.

    Figure 29 41 – ESR-21 rear panel

    Table 24 lists rear panel connectors of the router.

    ...

    The side panel layout of ESR-21 is depicted in figures 30 and 31below.

    Figure 30 42 – ESR-21 left side panel

    Figure 31 43 – ESR-21 right side panel

    ...

    The front panel layout is depicted in figure 32below.

    Figure 32 44 – ESR-20 front panel

    Table 25 lists connectors, LEDs and controls located on the front panel of ESR-30.

    Table 25 – Description of connectors, LEDs and controls located on ESR-30 front panel

    №

    Front panel element

    Description

    1

    110-250 VAC

    Power supply.

    2

    Power

    Device power LED.

    Status

    Current device status LED.

    Alarm

    Alarm LED.

    User

    LED for custom scenarios that can be assigned in device configuration mode.

    3

    F

    Functional key that reboots the device and resets it to factory default configuration: - pressing the key for less than 10 seconds reboots the device. – pressing the key for more than 10 seconds resets the device to factory default configuration.

    4

    Console

    Console port RS-232 (RJ-45) for local management of the device.

    5

    microSD

    microSD-card connector.

    6

    USB1

    USB 2.0 connector for connecting external USB devices.

    7

    USB2

    USB 3.0 connector for connecting external USB devices.

    8[1 .. 4]4 ports of 10/100/1000BASE-T.

    9

    1, 2

    2 ports of10GBASE-R (SPF+)/1000BASE-X.

    ESR-20 front panel

    The front panel layout is depicted in figure 33below.

    Figure 33 45 – ESR-20 front panel

    Table 26 lists connectors, LEDs and controls located on the front panel of ESR-20.

    ...

    The rear panel layout of ESR-20 and ESR-30 is depicted in figure 34below.

    Figure 34 46 – ESR-20, ESR-30 rear panel

    ...

    The side panel layout of ESR-20 and ESR-30 is depicted in figures 35 and 36below.

    Figure 35 47 – ESR-20, ESR-30 left side panel

    Figure 36 48 – ESR-20, ESR-30 right side panel

    ...

    The front panel layout is depicted in figure 37below.

    Figure 37 49 – ESR-15 front panel

    Table 28 lists connectors, LEDs and controls located on the front panel of ESR-15 router.

    Table 28 – Description of connectors, LEDs and controls located on ESR-15 front panel

    №

    Front panel element

    Description

    1F

    Functional key that reboots the device and resets it to factory default configuration:

    • pressing the key for less than 10 seconds reboots the device;
    • pressing the key for more than 10 seconds resets the device to factory default configuration.
    212V DCPower supply.
    3Optical ports2 ports of Gigabit Ethernet – 1000BASE-X (SFP).
    4USB1, USB22 USB connectors for connecting external USB devices.

    3

    Console

    Console port RS-232 (RJ-45) for local management of the device.

    9

    [1 .. 4]

    4 ports of Gigabit Ethernet 10/100/1000BASE-T (RJ-45).

    Scroll Pagebreak

    ESR-15 top panel

    The top panel layout of ESR-10 is depicted in figure 38below.

    Figure 50 – ESR-15 top panel

    Table 29 lists LEDs located on ESR-15 top panel.

    Table 29 – Description of front panel LEDs

    №

    Top panel element

    Description

    1

    Power

    Device power and operation status LED

    2

    -

    The LED is not used

    3

    USB1, USB2

    External USB devices LED

    4

    [1 .. 2]

    Ethernet ports LED

    5

    [3 .. 6]

    Optical interfaces LED

    Scroll Pagebreak

    ESR-14VF, ESR-12VF design

    ...

    The front panel layout is depicted in figure 39below.

    Figure 39 51 – ESR-14VF, ESR-12VF front panel

    ...

    The rear panel layout of ESR-12VF, ESR-14-VF is depicted in figure 40below.

    Figure 40 52 – ESR-12VF, ESR-14VF rear panel

    ...

    The side panel layout of ESR-12VF, ESR-14VF is depicted in Figures 41 and 42figures below.

    Figure 41 53 – ESR-12VF, ESR-14VF left side panel

    Figure 42 54 – ESR-12VF, ESR-14VF right side panel

    ...

    The front panel layout is depicted in figure 43below.

    Figure 43 55 – ESR-12V front panel

    Table 32 lists connectors, LEDs and controls located on the front panel of ESR-12VF router.

    Scroll Pagebreak

    ...

    The rear panel layout of ESR-12V is depicted in 44figure below.

    Figure 44 56 – ESR-12V rear panel

    Table 33 lists rear panel connectors of the router.

    Scroll Pagebreak

    ...

    The side panel layout of ESR-12V is depicted in figures 45 and 46below.

    Figure 45 57 – ESR-12V left side panel

    Figure 46 58 – ESR-12V right side panel

    ...

    The rear panel layout of the device is depicted in figure 47below.

    Figure 47 59 – ESR-10 rear panel

    Table 34 lists connectors, LEDs and controls located on the rear panel of ESR-10. 

    Scroll Pagebreak

    ...

    The side panel layout of ESR-10 is depicted in figure 48below.

    Figure 48 60 – ESR-10 side panel

    Table 35 lists right panel controls of the router.

    ...

    The top panel layout of ESR-10 is depicted in figure 49below.

    Figure 49 61 – ESR-10 top panel

    Table 36 lists LEDs located on ESR-10 top panel.

    ...

    Gigabit Ethernet copper interface statuses are represented by two LEDs – green LINK/ACT LED and amber SPEED LED. Location of the copper interface LEDs is depicted in figure 50. SFP interface status is represented by two LEDs – RX/ACT and TX/ACT – depicted in figure 51. For light indication meaning, see Tables 37 and 38 respectively.

    Якорь
    pic43
    pic43

    Figure 50 62 – Location of RJ-45 connector indicators

    Figure 51 63 – Location of optical interface indicators

    Scroll Pagebreak

    ...

    Table 39 – Status of system indicators

    Indicator name

    Indicator function

    LED State

    Device State

    Status

    Current device status LED.

    Green

    Device is in normal operation state.

    Red

    The device is in the firmware download state.

    Alarm

    Alarm LED.

    -

    -

    VPN

    Active VPN sessions indicator.

    -

    -

    Flash

    Activity indicator of exchange with data storages: SD-card or USB Flash.

    Green

    Read/write operation execution with 'copy' command.

    Power

    Device power LED.

    Green

    Device power is normal. Main power supply, if installed, is operational.

    Orange

    Main power supply failure, fault, or the primary network is missing.

    Off

    Device internal power supply failure.

    Master

    Indicator of failover modes operation.

    -

    -

    Fan

    Cooling fan status.

    Off

    All fans are operational.

    Red

    One or more fans has failed. Possible cause of failure: at least one of the fans has stopped or is working at lower rpm.

    RPS

    Backup power supply operation mode.

    Green

    Backup power supply is installed and operational.

    Off

    Backup power supply is not installed.

    Red

    Backup power supply is missing or failed.

    ESR-3200, ESR-3100, ESR-1511, ESR-1500 light indication

    Gigabit Ethernet copper interface and SFP interface statuses are represented by two LEDs – green LINK/ACT LED and amber SPEED LED. Location of the copper interface LEDs is depicted in figure 5264. SFP interface status is depicted in figure 5365. For light indication meaning, see Tables 40 and 41 respectively.

    Figure 52 64 – Location of RJ-45 connector indicators

    Figure 53 65 – Location of optical interface indicators

    ...

    Table 41 – Light indication of SFP/SFP+/QSFP+ status

    SPEED indicator is lit

    LINK/ACT indicator is lit

    Ethernet interface state

    Off

    Off

    The port is disabled or connection is not established.

    Solid on

    Solid on

    Connection is established.

    Flashes

    X

    Data reception is in progress.

    X

    Flashes

    Data transfer is in progress.

    The following table describes the states of the system LEDs on the device and their meanings.

    Table 42 – Status of system indicators

    Indicator name

    Indicator function

    LED State

    Device State

    Status

    Current device status LED.

    Green

    Device is in normal operation state.

    Orange

    Device is booting up the software.

    Alarm

    Device alarm presence and level indicator.

    -

    -

    VPNActive VPN sessions indicator.--
    FlashActivity indicator of exchange with data storages: SD-card or USB Flash.OrangeRead/write operation execution with 'copy' command.

    Power

    Device power LED.



    Green

    Device power is OK. Main power supply, if installed, is operational.

    Orange

    Main power supply failure, fault, or the primary network is missing.

    Off

    Device internal power supply failure.

    MasterIndicator of failover modes operation.--

    Fan

    Cooling fan status.


    Off

    All fans are operational.

    Red

    One or more fans has failed. Possible cause of failure: at least one of the fans has stopped or is working at lower rpm.

    RPSBackup power supply operation mode.GreenBackup power supply is installed and operational.
    OffBackup power supply is not installed.
    RedBackup power supply is missing or failed.

    Якорь
    table33_desc
    table33_desc

    ...

    Gigabit Ethernet copper interface and SFP interface statuses are represented by two LEDs – green LINK/ACT LED and amber SPEED LED. Location of the copper interface LEDs is depicted in figure 50. SFP interface status is depicted in figure 54. For light indication meaning, see Table 43.

    Figure 54 66 – Location of optical interface indicators

    Table 43 – Light indication of copper and SFP interfaces status

    SPEED indicator is lit

    LINK/ACT indicator is lit

    Ethernet interface state

    Off

    Off

    The port is disabled or connection is not established.

    Off

    Solid on

    10 Mbps or 100 Mbps connection is established.

    Solid on

    Solid on

    1000 Mbps connection is established.

    X

    Flashes

    Data transfer is in progress.

    The following table describes the states of the system LEDs on the device and their meanings.

    Table 44 – Status of system indicators

    Indicator name

    Indicator function

    LED State

    Device State

    Status

    Current device status LED.

    Green

    Device is in normal operation state.

    Red

    Device is booting up the software.

    Alarm

    Device alarm presence and level indicator1.

    -

    -

    Power

    Device power LED.



    Green

    Device power is OK. Main power supply, if installed, is operational.

    Red

    Main power supply failure, fault, or the primary network is missing.

    Off

    Device internal power supply failure.

    Fan

    Cooling fan status.


    Off

    All fans are operational.

    Red

    One or more fans has failed. Possible cause of failure: at least one of the fans has stopped or is working at lower rpm.

    ...

    1

    Якорь
    footnote
    footnote
    Not supported in current firmware version.

    ...

    SPEED indicator is lit

    LINK/ACT indicator is lit

    Ethernet interface state

    Off

    Off

    The port is disabled or connection is not established.

    Off

    Solid on

    10 Mbps or 100 Mbps connection is established.

    Solid on

    Solid on

    1000 Mbps connection is established.

    X

    Flashes

    Data transfer is in progress.

    Figure 55 67 – Location of SFP connector indicators

    Figure 56 68 – Location of RJ-45 connector indicators

    ...

    Table 47 – Light indication of copper and SFP interfaces status

    SPEED indicator is lit

    LINK/ACT indicator is lit

    Ethernet interface state

    Off

    Off

    The port is disabled or connection is not established.

    Off

    Solid on

    10 Mbps or 100 Mbps connection is established.

    Solid on

    Solid on

    1000 Mbps connection is established.

    X

    Flashes

    Data transfer is in progress.

    Figure 57 69 – Location of SFP connector indicators

    Figure 58 70 – Location of RJ-45 connector indicator

    ...

    Table 48 – Status of system indicators

    Indicator name

    Indicator function

    LED State

    Device State

    Power

    Device power LED.

    Green

    Device power is normal operation state. Main power supply, if installed, is operational. The main software is uploaded.

    Red

    The main software is not loaded.

    Off

    Device internal power supply failure.

    Status

    Current device status LED.

    Green

    Device is in normal operation state.

    Flashes green

    Device is booting up the software.

    Alarm

    Alarm LED.

    -

    -

    HA

    HA operation mode LED (not supported in the current version)

    -

    -

    ESR-15 light indication

    Gigabit Ethernet copper interfaces statuses are represented by amber SPEED LED.

    Table 49 – Light indication of copper interface status

    SPEED indicator is lit

    Ethernet interface state

    Off

    Port is disabled or connection is not established

    Solid amber on

    1000 Mbps connection is established

    Solid green on10 Mbps or 100 Mbps connection is established

    Flashes

    Data transfer is in progress

    The following table lists description of system indicator statuses and meanings.

    Table 50 – Status of system indicators

    Indicator name

    Indicator function

    LED State

    Device State

    Power

    Device power LED.

    Green

    Device power is normal operation state. Main power supply, if installed, is operational. The main software is uploaded.

    Red

    The main software is not loaded.

    Off

    Device internal power supply failure.

    USB1, USB2



    Indicators of operation of external USB devices.

    Green

    USB device is connected.

    Flashes green

    Read/write operation execution.

    OffNo devices connected or connectivity issues.

    ESR-12V(F) light indication

    ...

    SPEED indicator is lit

    LINK/ACT indicator is lit

    Ethernet interface state

    Off

    Off

    Port is disabled or connection is not established

    Off

    Solid on

    10 Mbps or 100 Mbps connection is established

    Solid on

    Solid on

    1000 Mbps connection is established

    X

    Flashes

    Data transfer is in progress

    Figure 57 71 – Location of SFP connector indicators (only for ESR-12VF, ESR-14VF)

    Figure 58 72 – Location of RJ-45 connector indicators

    ...

    Table 53 – Light indication of copper interface status

    SPEED indicator is lit

    Ethernet interface state

    Off

    Port is disabled or connection is not established

    Solid amber on

    1000 Mbps connection is established

    Solid green on10 Mbps or 100 Mbps connection is established

    Flashes

    Data transfer is in progress

    Table 54 – Status of system indicators

    Indicator name

    Indicator function

    LED State

    Device State

    Power

    Device power LED.

    Green

    Device power is normal operation state. Main power supply, if installed, is operational. The main software is uploaded.

    Red

    The main software is not loaded.

    Off

    Device internal power supply failure.

    USB1, USB2



    Indicators of operation of external USB devices.

    Green

    USB device is connected.

    Flashes green

    Read/write operation execution.

    OffNo devices connected or connectivity issues.

    Scroll Pagebreak

    Delivery package

    ...