...
The page displays the APs that are registered and located in the selected location.
The "Общее количествоTotal" parameter shows the number of registered APs in the selected location.
Use the "Unregister all" button to unregister the APs in the selected location. They will then move to "Точки доступаAccess Points" → "Новые точки доступаNew Access Points", if auto-registration is disabled. In case auto-registration is enabled, the APs will reappear in the location within 5 minutes.
...
- MAC-адрес – MAC address of the registered access point, move to "Точка доступаAccess Point" page by clicking;
- Разрегистрировать Unregister all – button allows to take the selected access point out of service and move it to the list of new access points;
- Статус Status – status of the access point operation;
- IP -адрес – Address – IP address of the registered access point;
- Модель –Board Type – model of the registered access point;
- Версия ПО SW Version – firmware version of the registered access point;
- Время работыUptime – operating time since the last time the device was turned on or rebooted;
- Количество клиентов Clients Count – number of clients connected to the registered access point, move to "Точка доступаAccess Point"→ "КлиентыClients" page by clicking;
More information will bw shown by clicking the 
button:
- Локация AP Location – name of the location to which the access point belongs;
- Описание статуса Status Description – additional status information if problems are detected on the access point;
- Серийный номер Serial Number – serial number of the device as set by the factory;
- HW -версия Version – hardware version of the device;
- Первая активность First Activity at – time when the access point was first registered on controller;
- Подключен в Connected at – time at which the access point was last connected to the controller;
- Последняя активность Last activity at – time at which the controller last configured the access point;
- Подключена через Configured as – profile with which the access point was configured;
- Состояние Netconf Connection State – status of the connection between the access point and the controller using the Netconf protocol;
- Описание – text Description – text description of the access point, which was assigned to it when forming the profile.
...
The basic information includes the following parameters:
- Client MAC -адрес клиента – MAC address of the connected device;
- AP MAC-адрес ТД – MAC address of the access point to which the device is connected;Интерфейс
- AP Hostname –
- Interface – interface of interaction between the access point and the connected device;
- SSID – network name to which the device is connected;Имя пользователя
- RSSI, dBm –
- User name – user name specified during authorization in the network. In case of personal authorization or when connecting to an open network, the user name will remain empty.
...
- IP-адрес – IP address of the connected device;
- Имя хоста – network name of the connected device;
- RSSI, дБм – received signal strength;
- SNR, дБ – signal-to-noise ratio;
- Канальная скорость передачи – modulation and channel rate when transmitting;
- Канальная скорость приема – modulation and channel rate at reception;
- Режим IEEE 802.11 – wireless network standard;
- Авторизован – client's authorization status;
- Домен – domain to which the user belongs;
- Качество соединения – parameter that displays the status of the link to the client, calculated based on the number of retransmitted packets sent to the client. The maximum value is 100% (all transmitted packets were sent on the first attempt), the minimum value is 0% (no packets were successfully sent to the client). The value of the parameter is calculated for the last 10 seconds;
- Общее качество соединения – parameter that displays the state of the link to the client, calculated based on the number of retransmitted packets sent to the client. The maximum value is 100% (all transmitted packets were sent on the first attempt), the minimum value is 0% (no packets were successfully sent to the client). The value of the parameter is calculated for the whole time of client connection;
- Скорость передачи, Кбит/c – actual speed of traffic transmission at the moment;
- Скорость приема, Кбит/c – actual rate of traffic reception at the moment;
- Передано, байт – number of bytes transmitted to the connected device;
- Принято, байт – number of bytes received from the connected device;
- Передано, пакетов – number of packets transmitted to the connected device;
- Принято, пакетов – number of packets received from the connected device;
- Время работы – time of connection with Wi-Fi client;
- Ширина полосы передачи, МГц – channel frequency bandwidth on which the radio interface operates during transmission;
- Ширина полосы приема, МГц –– channel frequency bandwidth on which the radio interface operates during receiving.
Scroll Pagebreak
...
RRM Reports
The page displays optimization reports. By default, the last report is displayed. Select the required report date using the calendar.
...
It is possible to download reports by clicking on the 
button.
The "Общее количествоTotal" parameter displays the number of radio interfaces for which optimization was performed.
- MAC -адрес Address – MAC address of the AP that is managed by Airtune;
- IP -адрес Address – IP address of the access point that is managed by Airtune;
- МодельBoard Type – AP type that is managed by Airtune;
- Время отчета Report Time – time at which the optimization report was generated;
- Мощность до/после оптимизации, дБм Power Before/After Optimization, dBm – AP power, the first number shows the value before optimization, the second value shows the power after optimization;
- Номер канала до/после оптимизации Channel Before/After Optimization – access point radio interface channel, the first number shows the value before optimization, the second value shows the radio interface channel after optimization;
- ДиапазонBand, ГГцGHz – frequency range of the radio interface.
...
The page displays data about the access points that are currently under the control of the Airtune serviceПри нажатии на кнопку "Terminate all Airtune sessions" от сервиса будут отключены все точки доступа, но будут сразу переподключены, если для них не будет отключена работа сервиса в конфигурации.
Clicking the "Terminate all Airtune sessions" button disconnects all access points from the service, but reconnect them immediately if the service is not disabled for them in the configuration.
The "Общее количествоTotal" parameter displays the number of APs currently managed by the Airtune service.
...
The table shows the following information:
- AP MAC -адрес ТД – MAC address of the AP that is currently under the control of Airtune service, when clicked advanced session information page will open;
- Разорвать сессию – button to break the session between the selected AP and Airtune service. The access point will be reconnected immediately if the service is not disabled in the configuration;
- IP-адрес – IP Address – IP address of the access point that is currently under the control of the Airtune service;
- Модель –Board Type – model of the access point that is currently under the control of the Airtune service;
- Session ID Сессии –– session ID number of the AP currently running the Airtune service.
Airtune -сессияSessions
The page displays the parameters of radio interfaces and the list of SSIDs on them. In order to update the information on the page, click on the button
.
...
- SSID – name of the network that is broadcast to users;
- Диапазон, ГГц – frequency range of the radio interface;
- MAC-адрес VAP – MAC address of the virtual access point;
- 802.11k – activity status of synchronization of lists of neighboring 802.11k access points, which allows the client, when the signal from the current access point weakens, to search for a more suitable access point from the recommended list, without analyzing the whole air;
- 802.11r – status of key negotiation activity between access points for 802.11r roaming, which allows to significantly accelerate the process of client switching between access points, because the client will not need to go through a second full authorization on the opposite access point, only accelerated.
...
RRM Statistics
The page displays the parameters of the access point radio interfaces after the last optimization.
The "Общее количество" parameter displays the number of radio interfaces. This list can be sorted by frequency range.
The table contains:
- AP MAC -адрес – MAC address of the access point that is managed by Airtune;
- ДиапазонBand, ГГцGHz – frequency range of the radio interface;
- Статус Status – status of the radio interface: Up – radio interface is activated, Down – radio interface is disabled;
- Блокировка Locked DCA – status of dynamic channel allocation blocking: 0 – blocking disabled, 1 – blocking activated;
- Блокировка locked TPC – automatic power control lock status: 0 – lock disabled, 1 – lock activated;
- Номер канала Channel – number of the wireless channel on which the radio interface operates;
- Ширина каналаBandwidth, МГц MHz – channel frequency bandwidth on which the radio interface operates;
- МощностьPower, дБм – dBm – signal power of the radio interface;
- Доступные каналы Available Channels – list of channels from which a channel is selected and assigned to the radio interface after optimization;
- Количество клиентов Associated Clients – number of clients connected to the radio interface.
...
Roaming Statistics
The page displays the entire list of virtual interfaces (SSIDs) that are processed by Airtune service. The page is designed to display the current state of 802.11 k/r roaming configuration on all location access points, as well as a list of all neighbors between which the service has configured roaming.
The "Общее количествоTotal" parameter displays the number of SSIDs configured on all access points. This list can be sorted by frequency range.
...
| Scroll Pagebreak |
|---|
- AP MAC-адрес ТД – MAC address of the access point;
- VAP MAC -адрес VAP – MAC address of the virtual access point;
- ДиапазонBand, ГГцGHz – frequency range of the radio interface;
- 802.11k – activity status of synchronization of lists of neighboring 802.11k access points, which allows the client, when the signal from the current access point weakens, to search for a more suitable access point from the recommended list, without analyzing the entire air;
- 802.11r – key negotiation activity status between access points for 802.11r roaming, which allows a client to significantly speed up the process of switching between access points, as the client will not need to go through a second full authorization on the oncoming access point, only an accelerated one.Количество соседей 802.11r – number of APs with which 802.11r seamless roaming has been configured, roaming neighbors are determined by a full match of SSID parameters such as 802.11r status, network name, range;
- FBT Links –
- SSID – network name that is broadcast to users.
...
The page displays the APs that are registered and under the control of the controller.
The "Общее количествоTotal" parameter shows the number of registered APs.
Use the "Unregister all" button to unregister access points from maintenance. They will then move to the "Новые точки доступаNew Access Points" section.
The table contains the following parameters:
- MAC -адресAddress – MAC address of the registered access point, when clicked the "Новые точки доступаNew Access Points" page will open;
- Разрегистрировать Unregister all – remove the selected access point from the service and move it to the list of new access points;
- Статус Status – access point operation status;
- IP -адрес – Address– IP address of the registered access point;
- Модель –Board Type – registered access point model;
- Версия ПО SW Version – registered access point firmware option;
- Время работыUptime – operating time since the last time the device was turned on or rebooted;
- Количество клиентов Clients Count – number of clients connected to the registered access point, when clicked "Точка доступаAccees Point"→ "КлиентыClients" page will open;
- Локация AP Location – location name to which the access point belongs.
...
Clicking the button will display additional information:
- Описание статуса Status Description – additional status information in case there are problems detected on the AP;
- Серийный номер Serial Number – device serial number as set by the factory;
- HW -версия Version – device firmware version;
- Первая активность First Activity at – time when the access point was first registered with the controller;
- Подключен в Connected at – time at which the access point was last connected to the controller;
- Последняя активность Last Activity at – time at which the controller last configured the access point;
- Подключена через Configured as – profile with which the access point was configured;
- Состояние Netconf Connection State – status of the connection between the access point and the controller using the Netconf protocol;
- Описание – Description – text description of the access point, which was assigned to it when the profile was created.
Точка доступаAccess Point
When clicking on the MAC address of the registered access point, the access point page will open, where the data on clients, radio interfaces and interfaces are presented.
...
The page contains a table of clients that are currently connected to the access point.
The "Общее количествоTotal" parameter displays the number of clients from all frequency bands. "2.4", "5" show the number of clients in each band respectively.
The table contains the following information:
- MAC -адрес Address – MAC address of the client device;
- IP -адрес Address – IP address that the client device has received;
- SSID – name of the network to which the device is connected;
- Время работы Uptime – operating time since the client device was connected to the SSID;
- RSSI, дБмdBm – level of the received signal;
- SNR, дБdB – signal-to-noise ratio;
- Режим Mode IEEE 802.11 – wireless network standard;
- Качество соединения Link Quality – parameter that displays the state of the link to the client, calculated based on the number of retransmitted packets sent to the client. The maximum value is 100% (all transmitted packets were sent on the first attempt), the minimum value is 0% (no packets were successfully sent to the client);
- Имя пользователяUsername – user name specified during network authorization. In case of personal authorization or when connecting to an open network, the username will remain empty;
- Домен Domain – domain to which the user belongs.
...
- Имя хоста – network name of the connected device;
- Интерфейс – interface between the access point and the connected device;
- Канальная скорость передачи – modulation and channel rate when transmitting;
- Канальная скорость приема – modulation and channel rate when receiving;
- Авторизован – client authorization status;
- Общее качество соединения – parameter that displays the status of the link to the client, calculated based on the number of retransmitted packets sent to the client. The maximum value is 100% (all transmitted packets were sent on the first attempt), the minimum value is 0% (no packets were successfully sent to the client). The value of the parameter is calculated for the whole time of client connection;
- Скорость передачи, Кбит/c – actual rate of traffic transmission at the moment of time;
- Скорость приема, Кбит/c – actual rate of traffic reception at the moment of time;
- Передано, байт – number of bytes transmitted to the connected device;
- Принято, байт – number of bytes received from the connected device;
- Передано, пакетов – number of packets transmitted to the connected device;
- Принято, пакетов – number of packets received from the connected device;
- Ширина полосы передачи, МГц – channel bandwidth on which the radio interface operates during transmission;
- Ширина полосы приема, МГц – channel bandwidth on which the radio interface operates during receiving.
Scroll Pagebreak
РадиоинтерфейсыRadio
The table with basic parameters of radio interfaces is presented on the page:
- MAC-адрес – MAC address of the radio interface;
- Статус – activity status of the radio interface;
- Номер канала – number of the wireless channel on which the radio interface operates;
- Частота, МГц – frequency on which the radio interface operates;
- Ширина канала, МГц – channel frequency bandwidth on which the radio interface operates;
- Мощность, дБм – signal power of the radio interface.
ИнтерфейсыInterfaces
The page contains information on all interfaces of the access point.
...
The page displays the access points that reached the controller and are waiting to be registered or are in the process of being registered.
The "Общее количествоTotal" parameter displays the number of unregistered access points.
Access points can be registered by clicking the "Register all" button. After that they will move to the "Точки доступаAccess Point" section.
- MAC -адресAddress – MAC address of the unregistered access point;
- Статус Status – operating status of the access point;
- IP -адрес – Address – IP address of the unregistered access point;
- Модель –Board Type – model of the unregistered access point;
- Версия ПО SW Version – firmware version of the unregistered access point;
- HW -версия – hardware Version – hardware version of the device;
- Серийный номер Serial Number – serial number of the device set by the factory.
...
The page presents a table containing errors that occurred while configuring the controller, or warnings that parameters will not be applied for any reason.
The "Общее количествоTotal" parameter displays the number of configuration warnings/errors.
Submenu "Journal"
The «Журнал» «Journal» submenu displays events and activities with access points and clients.
...
Access Points
The page displays a timestamped log of events with access points.
The "Общее количествоTotal" parameter displays the number of entries in the log.
...
The log is searched by keywords in the "СообщениеMessage" column.
| Scroll Pagebreak |
|---|
...
The page displays a timestamped log of Wi-Fi customer service events.
The "Общее количествоTotal" parameter displays the number of entries in the log.
...
The log is searched by keywords in the "СообщениеMessage" column.
Submenu "Clients"
The page displays the total number of clients, as well as their quantitative distribution by frequency bands. In order to update the information on the page, you should click on the «Обновить» the «Update» button.
The table shows the basic information on the client:
- Client MAC -адрес клиента – MAC address of the connected device;
- AP MAC-адрес ТД – MAC address of the access point to which the device is connected;Интерфейс
- AP Hostname –
- Interface – interface of interaction between the access point and the connected device;
- SSID – name of the network to which the device is connected;
- Локация RSSI, dBm –
- Location – location in which the access point is present to which the client device is connected;
- Имя пользователяUsername – user name specified during authorization in the network. In case of personal authorization or when connecting to an open network, the user name will remain empty.
...