...
The figure below shows the navigation elements of the web-interface. ЗАМЕНИТЬ СКРИН НИЖЕ
The user interface window is divided into five areas:
...
- Name
- Timezone
- Tunnel Mode
- Description
To edit an existing location, click on its name in the list. Configuring a location is divided into several steps, the steps can be performed in any order.
In the factory configuration, a location named "default-location" is created with the following settings:
- Description: default-location
- Tunnelling Client Traffic: enabled
- AP Settings: default-ap
- SSID profiles: default-ssid profile with Enterprise authorisation on local RADIUS server
- Radio Profiles: default_2g and default_5g
- Airtune Profiles: default_airtune
- AP Networks: AP of any subnet will be configured according to the settings of that location.
Local Settings
This step contains the location general settings:
...
This section allows defining the subnets of the AP that will be configured according to the rules of this location. To create a new subnet, use the button "
The following parameters are available:
- Name – subnet name. By default, the name is generated automatically and can be changed if necessary;
A profile with AP settings is added to the location. The presence of this profile in the location is obligatory. To add an existing profile to the location use “Attach”.
...
If necessary, you can edit an existing profile by clicking on its name or create a new one. The creation procedure and description of parameters are available in the menu "AP".
SSID Profiles
SSID profile can be added into a location. To do that use "Attach".
...
If necessary, you can edit an existing profile by clicking on its name or create a new one. The creation procedure and description of parameters are available in the menu "SSID".
Wireless Settings
To add radio profiles and airtune profiles to the location use "Attach".
...
- Name
- Status
- SSID
- Band, GHz
- VLAN ID
- Security Mode
- Description
In the factory configuration, SSID profile is created with the following settings:
...
To create a new SSID profile, use the "Create Profile" button. A window with a task to create a profile with standard settings and a generated name (which can be changed) will be opened. After clicking the “Save” button, the profile page will open for customizing the settings. If you need to cancel the creation of a new profile, use the “Cancel” button.
Common Settings
...
The advanced settings section is located at the bottom of the page and its parameters are hidden by default. To access the advanced settings, use the button 
.
The page contains the following parameters:
...
– server is enabled
– server is disabled
In the factory configuration, a profile named "default-ap" is created with the following settings:
...
AP profile configuration Якорь AP profile config AP profile config
The page contains the following parameters:
...
The AP services trace setup page is opened by clicking the "Redirect to Trace setup mode" in the upper right corner of the AP settings profile.
In most cases, AP services have the same logging settings, but some services have individual settings. In general, the logging settings of any service contain parameters:
...
Detailed information on working with the device configuration is described in the "КонфигурированиеConfiguration" section. After creating a profile, it will be displayed in the table of profiles "AP".
...
- Name
- Band, GHz
- Mode IEEE 802.11
- Bandwidth, MHz
- Tx Power
- Description
In the factory configuration, radio profiles named "default_2g" for 2.4 GHz and "default_5g" for 5 GHz are created with the following settings:
...
A window with a task to create a profile with standard settings and a generated name (which can be changed) will be opened. It is necessary to specify at once for which frequency range the profile is created. After clicking the “Apply” button, the profile page will open for customizing the settings. If you need to cancel the creation of a new profile, use the “Cancel” button.
The following parameters are shown on a radio profile page:
...
- Name
- Auth Server Address
- Auth Port
- Acct Server Address
- Acct Port
- Description
To edit an existing profile, click on its name. The profile settings page will be displayed.
In the factory configuration, RADIUS profile is created with the following settings:
...
A window with a task to create a profile with standard settings and a generated name (which can be changed) will be opened. After clicking the “Save” button, the profile page will open for customizing the settings. If you need to cancel the creation of a new profile, use the “Cancel” button.
The following parameters are shown on a RADIUS profile page:
General:
...
- Name
- DCA
- TCP
- Optimization Mode
- Optimization Time
- Description
To edit an existing profile, click on its name. The profile settings page will be displayed.
In the factory configuration, profile named "default-airtune" is created with the following settings:
...
To create new Airtune profile use "Create Profiles" button. A window with a task to create a profile with standard settings and a generated name (which can be changed) will be opened. After clicking the “Save” button, the profile page will open for customizing the settings. If you need to cancel the creation of a new profile, use the “Cancel” button.
The following parameters are shown on Airtune profile page:
General:
...
| Информация |
|---|
To edit common settings, the edit mode must be enabled. |
In the factory configuration, the general settings have the following values:
...