...
| WLC model | HW version | Firmware | Secondary bootloader | Primary bootloader |
|---|---|---|---|---|
| WLC-15 | all | wlc15-1.30.46-build25build20.firmware | wlc15-1.30.46-build26build21.uboot | none |
| WLC-30 | all | wlc30-1.30.46-build25build20.firmware | wlc30-1.30.46-build26build21.uboot | none |
WLC-3200 | all | wlc3200-1.30.46-build24build20.firmware | wlc3200-1.30.46-build25build21.uboot | wlc3200-1.30.46-build25build21.bdk |
| ESR-15 | all | esr15-1.30.46-build25build20.firmware | esr15-1.30.46-build26build21.uboot | none |
| ESR-15R | all | esr15-1.30.46-build25build20.firmware | esr15-1.30.46-build26build21.uboot | none |
| ESR-30 | all | esr3x-1.30.46-build25build20.firmware | esr3x-1.30.46-build26build21.uboot | none |
ESR-3200 | all | esr3200-1.30.46-build25build20.firmware | esr3200-1.30.46-build26build21.uboot | esr3200-1.30.46-build26build21.bdk |
| vWLC | — | vwlc-1.30.46-build25build20.firmware | — | — |
Creating a backup copy of the current configuration
...
Firmware update via CLI of the WLC main firmware
Firmware update from version 1.30.4 to 1.30.6
| Информация |
|---|
ESR-15, ESR-30, ESR-3200, vWLC are updated using the same algorithm. |
| Предупреждение |
|---|
Before updating, use the show date command to verify that the correct date and time are set on the device. If an incorrect date is set on the controller, certificate validation will prevent the configuration changes from being applied after the update. |
Firmware version 1.30.6 is cumulative (it contains updated versions of the primary and secondary loaders), so it will be enough to:
- Make a backup copy of the configuration.
- Check that the date and time on the controller are correct.
- Download the firmware for the AP to the controller.
- Download the firmware for the WLC controller.
- Select fimware image version 1.30.6 for the next download.
| Предупреждение |
|---|
Turning off the power before the boot system {image-1|image-2} command is finished may cause the controller to malfunction. |
- Reboot the controller.
Minimal firmware version of AP:
- WEP-1L/2L and WOP-2L — 2.8.0 or higher
- WEP-30L/WEP-30L-NB/30L-Z and WOP-30L/30LI/30LS — 2.8.0 or higher
- WEP-200L and WOP-20L — 2.8.0 or higher
- WEP-3L, WOP-3L-EX — 2.8.0 or higher
- WEP-3ax — 1.15.0 or higher
- WEP-2ac/2ac Smart, WOP-2ac/2ac rev.B/2ac rev.C — 1.25.2 or higher
- WEP-550K — 1.1.0 or higher
The firmware for the AP must be downloaded to the controller before updating it. Then after rebooting the WLC, the AP will automatically update to the new firmware. If the firmware has been downloaded to the controller after it has been updated, then the clear wlc ap command must be executed to reconnect the APs and update the firmware.
| Информация |
|---|
Updating to version 1.30.4 can be done from any previous version, but the recommendations for each version described below must be followed. When updating from version 1.15.3, the secondary bootloader must be updated at the same time as the main firmware (see section Secondary bootloader update). |
| Scroll Pagebreak |
|---|
Firmware update from version 1.30.2 to 1.30.4
...