|
RR-10 – universal wireless signal repeater designed to expand the coverage area of wireless networks and amplify Wi-Fi signal. The device allows you to eliminate blind spots and optimize the performance of your Wi-Fi network.
With support for IEEE 802.11n/ac standards, RR-10 repeater provides high data transfer rates and is capable to provide high-quality multimedia transmission of 4K content. The use of MIMO technology and internal antennas makes RR-10 a universal solution for expanding your home network.
RR-10 supports EasyMesh technology and can be used in EasyMesh network as an agent.
The device is powered by an external 5.3V adapter from 220V power network.
Interfaces:
Functions:
2.4 GHz repeater:
5 GHz repeater:
Access point:
When used with the RG-35-WZ router (firmware version 2.2.0 or later), the RR-10 repeater will act as an EasyMesh agent after being configured via WPS. |
General parameters | |
---|---|
Clock frequency | 1 GHz |
RAM | 128 MB |
ROM | 16 MB |
Operating system | Linux 3.10 |
LAN Ethernet interface parameters | |
Number of interfaces | 1 |
Connector type | RJ-45 |
Data rate, Mbps | 10/100/1000, autonegotiation |
Standards | BASE - T |
Wireless interface parameters | |
Number of antennas | 2 |
Antenna type | internal |
Standards | 802.11 a/b/g/n / ac/k/v |
Frequency range | 2412-2472 MHz |
MIMO | 2. 4 MHz 2х2 5 MHz 2х2 |
Modulation | 2,4 MHz: DSSS, CCK, BPSK, QPSK, 16QAM, 64QAM 5 MHz: BPSK, QPSK, 16QAM, 64QAM, 256QAM |
Data transfer rate | 802.11b: up to 11 Mbps |
Maximum transmitter output power 1 | 2.4 GHz: up to 18 dBm |
Receiver sensitivity | 2.4 GHz: up to -98 dBm |
Security | WPA (TKIP+AES), WPA2 (TKIP+AES), WPA/WPA2 (TKIP+AES) |
Control | |
Remote control | web interface |
Access restriction | by password |
Physical specifications | |
Power | external 5.3V DC, 2А power adapter |
Maximum power consumption | 7 W |
Range of operation temperatures | from +5 to +40°C |
Relative humidity at 25°C | up to 80% |
Dimensions (Diameter x Height) | 100 x 23 mm |
Weight | 85 g |
1 The value of the maximum output power will vary according to the rules of radio frequency regulation in your country
RR-10 wireless signal repeater is implemented in a plastic case with dimensions of Ø100 x 23 mm.
Front panel of RR-10
Description of front panel LED indicators
# | LED | LED status | Device state |
---|---|---|---|
1 | LED shows the device operation status | Solid red | The device is launching (1 minute max.) |
Red, flashing rapidly | The device is updating/reseting | ||
Red, flashing slowly | The device is turned on, there is no connection to the access point (router) | ||
Green, flashing rapidly | The device is connecting to an access point (router) through WPS technology | ||
Green, flashing slowly | The device is connected to an access point (router), no access to the Internet | ||
Solid green | The device has been connected to an access point (router) and has access to the Internet |
Rear panel of RR-10
# | Rear panel element | Description |
---|---|---|
1 | Button for client connection via the WPS protocol | |
2 | LAN | 10/100/1000BASE-T (RJ-45) port for connection to external networks |
3 | LEDs | LAN connector indicators |
4 | 5v DC | Connector for power adapter connection |
LAN connection indication
LED status | Device state |
---|---|
Only green lights | The connection is established at 10/100 Mbps |
Green and orange lights | The connection is established at 1000 Mbps |
Flashes green | The process of packet data transmission through LAN interface |
Bottom panel of RR-10
Description of bottom panel controls
# | Bottom panel element | Description |
---|---|---|
1 | F | Button for reseting to factory settings |
To reset the device to factory settings, press and hold the «F» button for more than 3 seconds until the indicator on the front panel flashes red. The device will automatically restart within 5 seconds, and the indicator will light up red. When the device is ready, the indicator flashes red slowly.
By default, the DHCP server is running on all interfaces; LAN interface address is 192.168.0.1; the subnet mask is 255.255.255.0; the username/password for access via the web interface: admin/password. |
The device supports connection to the router Wi-Fi networks via WPS. To configure the connection, activate the WPS function on the router and press and hold the WPS button on the back of the device for 3 seconds. After that the device will connect to the router automatically. Connection to the router takes no more than two minutes. In case the connection is not successful, try again and make sure that the WPS function on the repeater was activated no later than 2 minutes after the WPS function was activated on the router.
Configuring with WPS technology as a client is only available for non-configured devices. Before using the WPS button, you must reset the device to the factory settings. |
After configuring the device, a DHCP client is launched on all interfaces. |
RR-10 standard delivery package includes:
In order to avoid components overheating and device malfunctioning, do not place objects on the device. |
To extend Wi-Fi coverage area, connect RR-10 to the network of your access point (or router).
Press WPS button on the Wi-Fi router.
The way of WPS connection may vary for different routers. Please, read the manual for your router. |
Usually, you have 2 minutes after pressing WPS button on the router to press WPS on RR-10 for successful connection. |
By default, the repeater copies the name and Wi-Fi settings of the network to which it will be connected in both ranges: 5 GHz and 2.4 GHz. If necessary, you can change the name and Wi-Fi network settings via the web interface. |
When connecting to the RG-35 router with the firmware version 2.2.0 or later the RR-10 repeater will be automatically configured as an agent in the EasyMesh network. In the EasyMesh network all network parameters are synchronized between the controller and agent. |
1. Connect RR-10 to 220V power network through the power adapter near the Wi-Fi router (or access point) you want to connect to. Wait until LED start flashing red.
2. Connect to the repeater using smartphone or PC through Wi-Fi or Ethernet cable.
a. Through Wi-Fi: connect PC or smartphone to a Wi-Fi network of the repeater — RR-WiFi-XXXX (where XXXX is the last 4 characters of RR-10 MAC address, the MAC address is written on the label on the device case).
b. Through Ethernet cable (only for PC): connect LAN port of the repeater to LAN port of your PC using Ethernet cable.
3. Open a web browser and type the address of the device to URL bar — http://rr.loc/ или http://192.168.0.1 .
4.Enter username and password to the authorization window. Default username and password are admin and password correspondingly. Click «Log in».
5. The «Wizard» window will appear. Set a username and password to access the repeater web interface. Click «Next».
6. In the list that appears, select your Wi-Fi network and click on the line with its name.
7. Specify a password for your Wi-Fi network, as well as the name of the repeater network, then click «Connect». When repeater is connected to the Internet, the indicator will light green.
By default, the repeater copies the name and Wi-Fi settings of the network to which it will be connected in both ranges: 5 GHz and 2.4 GHz. If necessary, you can change the name of the network in the last step of the wizard, as well as change the name and settings is available later through the web interface on the page «Extended Network» in the «Wi-Fi» tab. |
EasyMesh network configuration via web interface is not available in firmware version 1.2.0. It is necessary to use the method of connection via WPS. |
EasyMesh network configuration via Ethernet cable is not available in firmware version 1.2.0. |
When using the RR-10 repeater together with the RG-35 router it is possible to operate in EasyMesh agent mode.
1. Connect RR-10 to 220V power network using power adapter next to EasyMesh controller (RG-35 router). Wait until LED start flashing red slowly.
2. Ensure that RG-35 has EasyMesh controller mode enabled. Press the WPS button on RG-35.
3. Press and hold WPS button on RR-10 untill the indicator start flashing green. When repeater is connected to the Internet, the indicator will light green.
You have 2 minutes after pressing WPS button on the RG-35 router to press WPS on RR-10 for successful connection. |
4. The RG-35 web interface will display changes in the EasyMesh network topology:
5. Changing agent name will be available in repeater web interface:
In EasyMesh agent mode the repeater will copy the name and Wi-Fi network parameters from the EasyMesh controller separately for the 5 GHz and 2.4 GHz bands. In the EasyMesh network, the parameters that are changed on controller, are synchronized between the controller and agent. |
Please note that in EasyMesh agent mode the web interface will automatically change under EasyMesh. Changing Wi-Fi parameters on the repeater will not be available. All changes in Wi-Fi parameters should be made on the EasyMesh controller. |
1. To start, you need to connect the device through LAN or Wi-Fi interface:
Connect your PC, phone or tablet to the device Wi-Fi network ( RR-WiFi-XXXX , where XXXX – last 4 characters of RR-10 MAC address);
Connect your PC to the device using an Ethernet cable.
2. Open a web browser, enter the address of the device.
Factory device address: http://rr.loc/ , IP address: 192.168.0.1, subnet mask: 255.255.255.0 |
If you connected to a Wi-Fi network with an already configured repeater, make sure that you are connected to the repeater and not to the access point (router), otherwise access to http://rr.loc will not be available. |
If connection is successful, web interface window with request form with user name (login) and password will be displayed on a browser.
3. Enter login and password .
Factory default: login – admin, password – password. |
4. Click the «Log in» button. The «Wizard» page will open in the browser window.
If the device was already configured, the «Status» page will open. The «Wizard» page is only available on a device with factory default settings. |
All changes to the device settings are made using the «control panel» tabs located at the top of the web interface and links to pages located on the left side of the web interface.
Main elements of the web interface
In the repeater mode, the web interface displays 4 tabs.
This tab displays information on the device's wireless interfaces and wireless clients that are connected to the device.
The «Uplink Connection» block contains information about the networks to which the repeater is connected for their expansion.
The «Extended Network» block contains information about the repeater's access points. Repeater clients are connect to this network.
The «Clients List» block contains information about wireless clients connected to the repeater.
This page displays information about the device.
This page displays information on the status of wired and wireless interfaces, received and sent packets and data bytes.
On the «Connect to a Network» page you can configure the RR-10 connection to the access point (router) network.
2. Select the desired Wi-Fi network, enter the password of this network and click «Connection».
If your Wi-Fi network uses the hidden SSID feature, it will not be displayed in the scan results. To connect to such a network, use the item «Connect to a Hidden Network». |
3. Click the «Connection» button to save and apply settings, or the «Cancel» button to return to the saved device configuration.
After connecting to the access point network, its parameters (network name, encryption mode, security type, password, channel) will be copied into both ranges: 5 GHz and 2.4 GHz. |
To avoid failures of device operation, it is not recommended to turn off the device while settings are being applied. |
3. Click the «Connection» button to save and apply settings, or the «Cancel» button to return to the saved device configuration.
After connecting to the access point network, its parameters (network name, encryption mode, security type, password, channel) will be copied into both ranges: 5 GHz and 2.4 GHz. |
To avoid failures of device operation, it is not recommended to turn off the device while settings are being applied. |
On the «Extended Network» page, you can change the basic settings for RR-10 wireless interfaces.
It is recommended to use WPA2 and WPA/WPA2 (Mixed) security modes as the most secure. |
The «Network» tab contains the device's local network settings.
The «DHCP server» option is available in the default settings only. After connecting the device to an access point, this item becomes unavailable. |
Please note that if you connect an access point (router) to the network via Ethernet, you will need to manually configure the extended device network. By default, the extended device network does not use encryption and password. |
On the «Admin Account» page, you may set login and password for accessing the device web interface.
To apply the new settings, click the «Apply» button. To cancel changes, leave the page without saving the changes, or click the «Cancel» button.
For the security purposes, it is recommended to change login and password during the device configuration. |
Login and password can also be set on the first step of the Wizard. |
The «Firmware upgrade» page is used to update the device control firmware.
Do not switch off or reboot the device during the firmware update. |
The «Configuration» page is designed to change the device configuration.
In EasyMesh agent mode, the web interface adapts to EasyMesh technology. There are changes in the «Status» tab on the «Network Map» page. The «Network» and «System» tabs remain unchanged. The «Wi-Fi» tab is replaced by the «EasyMesh» tab.
This tab displays information on the device's wireless interfaces and wireless clients that are connected to the device.
The «EasyMesh Network» block contains information about active EasyMesh connection.
The «Extended EasyMesh Network» block contains information about the device access points. Repeater clients are connect to this network.
The «Clients List» block contains information about wireless clients connected to the repeater.
On the EasyMesh configuration page you can change the device name in the EasyMesh network.
In the EasyMesh agent mode, changing Wi-Fi parameters on the agent is not available. All configuration changes must be performed through the EasyMesh controller. |
In the EasyMesh network, the parameters that are changed on controller (Wi-Fi network name, password, channel), are synchronized between the controller and agent. |
Problem | Possible cause | Solution |
---|---|---|
It is not possible to access the device's web interface by addresses http://rr.loc or http://192.168.0.1 | The device has not been launched, the indicator is red | Wait for the device to launch. If it takes more than 2 minutes to launch, restart the device. |
The IP address of the device was received from the DHCP server in the access point network, the indicator is green | Use the address given to the device by the DHCP server to access the web interface. The information can be accessed in the web interface of the router to which the repeater is connected. | |
When connecting via Wi-Fi, another network is used | Make sure that your device is connected to the SSID «RR-WiFi-XXXX» (where XXXX is the last 4 characters of the RR-10 MAC address) and the «Cellular data» function (if available) is disabled. If your device is connected to an access point (router) network – make sure that your device is connected to it. | |
When connecting via LAN, the client uses static network settings | Make sure that the computer is connected to the repeater using an Ethernet cable, and that its network settings are set to «Attain IP address automatically» and «Attain DNS server address automatically». | |
Device failures | Reset the repeater to factory settings and try again. | |
Wi-Fi network of the needed router is not displayed after clicking the «Wireless Scanner» button. | The Wi-Fi network uses a hidden SSID | Fill in the parameters manually. |
The signal strength of the Wi-Fi network is too weak | Increase the Wi-Fi signal level of your access point (router), or install the device closer to the access point (router) according to the installation recommendations. | |
Router uses unsupported WEP encryption mode | Change the encryption mode on the router to WPA, WPA2 or WPA/WPA2. | |
Unable to connect to the router Wi-Fi network via WPS | WPS is not configured on the router | Make sure that WPS technology is configured on the router. |
No WPS button on router | Make sure that the router supports WPS technology. Some routers have functionality to enable WPS via web interface. | |
WPS was not activated by a button on the router | Different routers can offer different ways to activate WPS (either by holding down a button or by pressing a single button). Please, read the manual for your router. | |
Device failures | Reset the repeater to factory settings and try again. | |
Unable to connect to the router Wi-Fi network via web interface | Incorrect password was entered | Re-enter the password. |
Router Wi-Fi network is not enabled or does not work | Make sure that the router Wi-Fi network is enabled and operates. | |
No Wi-Fi settings in web interface | Device operates in EasyMesh agent mode | Configure the EasyMesh network via the web interface of the controller. |
Firmware version | Document version | Issue date | Revisions |
---|---|---|---|
Version 1.2.0 | Issue 3 | 10.2020 | Changes in sections: |
Version 1.1.0 | Issue 2 | 04.2020 | Changes in sections: - Symbols - Device management via the web interface Chapters added: - Connecting RR-10 to a network > Connection via web interface in access point mode - Installation order > EasyMesh agent mode - Device management via the web interface > Repeater mode - Device management via the web interface > EasyMesh agent mode |
Version 1.0.0 | Issue 1 | 10.2019 | First issue |