|| DeviceType | Wireless access point |
|| DeviceName | WEP-2L |
|| DocTitleMain |  |
|| DocTitleAdditional | User manual |
|| fwversion | 1.2.2 |
|| issueDate | 01.2022 |
|| ipaddr | 192.168.1.10 |
|| username | admin |
|| password | password |

Introduction

Annotation

Modern tendencies of telecommunication development necessitate operators to search for the most optimal technologies, allowing you to satisfy rapidly growing needs of subscribers, maintaining at the same time consistency of business processes, development flexibility and reduction of costs of various services provision. Wireless technologies are spinning up more and more and have paced a huge way for short time from unstable low-speed communication networks of low radius to broadband networks equitable to speed of wired networks with high criteria to the quality of provided services.

WEP-2L is dedicated to be installed inside buildings as an access point and to create a seamless wireless network using several identical access points (“Roaming”) on a large area.

This manual specifies intended purpose, main technical parameters, design, safe operation rules and installation and configuration recommendations for WEP-2L.

Symbols

Notes and warnings

Device description

Purpose

WEP-2L wireless access point is designed for provision of users' access to high-speed safe network.

The device is dedicated to create L2 wireless networks interfacing with a wired network. WEP-2L is connected to a wired network via 10/100/1000M Ethernet interface and arrange high-speed access to the Internet for devices supporting Wi-Fi technology at 2.4 and 5 GHz.

The device has two radio interfaces to organize two physical wireless networks.

WEP-2L supports up-to-date requirements to service quality and allows transmitting more important traffic in higher priorities queues. Prioritization is based on main QoS technologies: CoS (special tags in VLAN packet field) and ToS (tags in IP packet field).

ACL rule creation functionality and support for traffic shaping on each VAP allows you to fully manage access, service quality and restrictions, both for all subscribers and for everyone in particular.

The devices are designed to be installed in offices, state buildings, conference halls, laboratories, hotels, etc. The creation of virtual access points with different types of encryption allows clients to delimit access rights among users and groups of users.

Device specification

Interfaces:

• 1 port of Ethernet 10/100/1000BASE-T(RJ-45) with PoE+ support;

• Wi-Fi 2.4 ГГц IEEE 802.11b/g/n;

• Wi-Fi 5 ГГц IEEE 802.11a/n/ac.

Functions:

WLAN capabilities:

• Support for IEEE 802.11a/b/g/n/ac standards;
• Support for IEEE 802.11r/k/v roaming standarts;
• Data aggregation, including A-MPDU (Tx/Rx) and A-MSDU (Rx);
• WMM-based priorities and packet planning;
• WDS;
• Dynamic frequency selection (DFS);
• Support for hidden SSID;
• 8 virtual access points
• Third-party access point detection;
• Spectrum analyzer;
• Channel autoselection.

Network functions:

• Autonegotiation of speed, duplex mode and switching between MDI and MDI-X modes;
• IPv6;
• Support for VLAN;
• Authentication support 802.1X;
• DHCP client;
• ACL;
• NTP;
• Support for Syslog;
• GRE;
• GRE over IPsec;
• Transmission of subscriber traffic out of tunnel.

QoS functions

• Priority and profile-based packet scheduling;
• Bandwidth limitation for each VAP;
• Bandwidth limitation for each client;
• WMM parameters changing.

Security

• Centralized authorization via RADIUS server (WPA Enterprise);
• WPA/WPA2;
• Captive Portal.

The figure below shows WEP-2L application scheme.

Figure 1 — WEP-2L application scheme

The device technical parameters

Table 1 — Main Specifications

Design

WEP-2L enclosed in plastic case.

Device main panel

The main panel layout of the device is depicted in Figure 2.

Figure 2 — WEP-2L main panel layout

Connectors and controls located on the device main panel are listed in Table 2.

Table 2 — Description of ports and controls

Light indication

The current device state is displayed by Wi-Fi, LAN, Power indicators. The list of indicators’ possible states is given below.

Table 3 — Light indication of device state

Reset to the default settings

In order to reset the device to factory settings, press and hold the “F” button until “Power” indicator starts flashing. Device will be rebooted automatically. DHCP client will be launched by default. If the address is not obtained via DHCP, the device will have the default IP address — 192.168.1.10, and the following netmask — 255.255.255.0.

Delivery package

The delivery package includes:

• WEP-2L wireless access point;
• Mounting kit;
• Operations manual on a CD (optional);
• Conformity certificate;
• Technical passport.

Rules and recommendations for device installation

This section defines safety rules, installation recommendations, setup procedure and the device starting procedure.

Safety rules

1. Do not install the device close to heat sources or in rooms with temperature below 5 °C or above 40 °C.
2. Do not use the device in places with high humidity. Do not expose the device to smoke, dust, water, mechanical vibrations or shocks.
3. Do not open the device case. There are no user serviceable parts inside.

Installation recommendations

1. The recommended installation: Horizontal, on a ceiling.
2. Before you install and enable device, check the device for visible mechanical defects. If defects are observed, you should stop the device installation, draw up corresponding act and contact the supplier.
3. If the device has been exposed for a long time at a low temperature, it must be left to stand for two hours at room temperature before use. After a long stay of the device in conditions of high humidity, let it stand under normal conditions for at least 12 hours before switching on.
4. During the device installation to provide Wi-Fi coverage area with the best characteristics take into account the following rules:
   1. Install the device at the center of a wireless network;
   2. Minimize the number of obstacles (walls, roof, furniture and etc.) between access point and other wireless network devices;
   3. Do not install the device near (about 2 m) electrical and radio devices;
   4. It is not recommended to use radiophone and other equipment operating on the frequency of 2.4 GHz, 5 GHz in Wi-Fi effective radius;
   5. Obstacles in the form of glass/metal constructions, brick/concrete walls, water cans and mirrors can significantly reduce Wi-Fi action radius. It is not recommended to place the device inside a false ceiling as metal frame causes multipath signal propagation and signal attenuation.
5. During the installation of several access points, cell action radius must overlap with action radius of a neighboring cell at level of -65 ÷ -70 dBm. Decreasing of the signal level on cells borders to -75 dBm is permitted if it involves the use of VoIP, streaming video and other traffic that is sensitive to losses in wireless network.

Calculating the number of required access points

To calculate the required number of access points, you should evaluate the required coverage zone. For a more accurate assessment, it is necessary to make a radio examination of the room. Approximate radius of coverage area of WEP-2L with a good-quality signal in case of mounting on a ceiling in typical office: 2.4 GHz 40-50 m, 5 GHz: 20-30 m. In the absence of obstacles, the coverage radius: 2.4 GHz up to 100 m; 5 GHz up to 60 m.
The table below describes rough attenuation values.

Table 4 — Attenuation values

Channel selection for neighboring access points

It is recommended to set nonoverlapping channels to avoid interchannel interference among neighboring access points.

 
Figure 3 — General diagram of frequency channel closure in the range of 2.4 GHz

For the example of channel allocation scheme among neighboring access points in frequency range of 2.4 GHz when channel width is 20 MHz, see Figure 4.

Figure 4 — Scheme of channel allocation among neighboring access points in the frequency range of 2.4 GHz when channel width is 20 MHz

Similarly, the procedure of channel allocation is recommended to save for access point allocation between floors, see Figure 5.

Figure 5 — Scheme of channel allocation between neighboring access points that are located between floors

When width of used channel is 40 MHz there is no non-overlapping channels in frequency range of 2.4 GHz. In such cases, you should select channels maximally separated from each other.

Figure 6 — Channels used in range of 5 GHz when channel width is 20, 40 or 80 MHz

Installing WEP-2L

The device should be attached to plain surface (wall or ceiling) in accordance with the safety instruction and recommendations listed above.
The device delivery package includes required mounting kit to attach the device to plain surface.

Wall mounting

1. Fix the bracket (included in the delivery package) to the wall:

Figure 7 — Attaching the bracket to a wall

1. 1. The figure shows the bracket allocation.
   2. When installing the bracket, pass wires through the corresponding channels of the bracket, see figure 7.
   3. Pass the wires into the corresponding grooves on the bracket while installing the bracket. Screw the brackets to the device surface by using screwdrive.

2. Install the device

 
Figure 8 — Device installation (front view)

1. 1. Connect cables to corresponding connector of the device. Description of the connectors is given in section 2.4 Design.
   2. Align the device and bracket together, fix the position, turning clockwise.

Installing to false ceiling

1 — metal bracket; 2 — armstrong panel; 3 — plastic bracket; 4 — device.

Figure 9 — Mounting to a false ceiling

1. Fasten metal and plastic bracket on a ceiling as shown in the figure 9.
   1. The plastic bracket (3) should be joined with the metal one (1) on the ceiling in the following order: metal bracket -> armstrong panel -> plastic bracket.
   2. Cut the hole in the armstrong panel. The size of the hole should be equal to hole of metal bracket. Conduct wires through the hole.
   3. Align holes in metal bracket with holes of armstrong panel and plastic bracket. Align together three boltholes on the plastic bracket and the boltholes on the metal bracket. Screw the brackets to the device surface by using a screwdrive.
2. Install the device.
   1. Connect cables to corresponding connector of the device. Description of the connectors is given in section 2.4 Design.
   2. Align the device and plastic bracket together, fix the position, turning clockwise.

Removing the device from the bracket

For removing the device from the bracket:

1. Turn the device counter-clockwise, figure 7.
2. Remove the device.

Device management via the web interface

Getting started

In order to start the operation, you should connect to the device via WAN interface using a web browser:

1. Open a web browser, for example, Firefox, Opera, Chrome.

2. Enter the device IP address in the browser address bar.

When the device is successfully detected, username and password request page will be shown in the browser window

3. Enter your username into “Login” and password into “Password” field.

4. Click the “Log in” button. A menu for monitoring the status of the device will open in a browser window.

5. If necessary, you can switch the information display language. Russian and English languages are available for web interface.

Applying configuration and discarding changes

1. Applying configuration

Visual indication of the process current status of the setting application process is realised in the web interface, table 7.

Table 7 — Visual indication of the current status of the setting application process

2. Discarding changes

The button for discarding changes appears as follows: .

Web interface basic elements

Navigation elements of the web interface are shown on the figure below

User interface window is divided into five general areas:

1. Menu tabs categorize the submenu tabs: Monitoring, Radio, VAP, Network settings, External Services, System.
2. Interface language selection and Logout button designed to to end a session in the web interface under a given user.
3. Submenu tabs allow you to control settings field.
4. Devcie configuration field displays data and configuration.
5. Information field displays current firmware version.

The “Monitoring” menu

In the “Monitoring” menu you can view the current system state.

The “Wi-Fi clients” submenu

The “Wi-Fi clients” submenu displays information about the status of connected Wi-Fi clients.

Information on connected clients is not displayed in real time. In order to update the information on the page you should click the “Update” button.

• № — number of the connected device in the list;
• Hostname — network name of the device;
• IP address — IP address of the connected device;
• MAC address — MAC address of the connected device;
• Interface — interface of WEP-2L communication with the connected device;
• Link Capacity — parameter that reflects the effectiveness of the use of a modulation access point on the transmission. It is calculated based on the number of packets transmitted on each modulation to the client, and the reduction factors. The maximum value is 100% (means that all packets are transmitted to the client at maximum modulation for the maximum nss type supported by the client). The minimum value is 2% (in the case when the packets are transmitted to the modulation nss1mcs0 for a client with MIMO 3x3 support). The parameter value is calculated for the last 10 s.
• Link Quality — parameter that displays the status of the link to the client, calculated based on the number of retransmit packets sent to the client. The maximum value is 100% (all transmitted packets were sent on the first attempt), the minimum value is 0% (no packets were successfully sent to the client). The parameter value is calculated for the last 10 s.
• Link Quality Common — parameter that displays the status of the link to the client, calculated based on the number of retransmit packets sent to the client. The maximum value is 100% (all transmitted packets were sent on the first attempt), the minimum value is 0% (no packets were successfully sent to the client). The parameter value is calculated for the entire client connection time.
• RSSI — received signal level, dBm;
• SNR — signal/noise ratio, dB;
• TxRate — channel transmission rate, Mbps;
• RxRate — receive channel rate, Mbps;
• Tx BW — transmission bandwidth, MHz;
• Rx BW — reception bandwidth, MHz;
• Uptime — Wi-Fi client connection uptime.

To display more detailed information on a particular client, select it from the list. A detailed description includes the following options: 

• Total TX/RX, bytes — the number of bytes sent/received on the connected device;
• Total TX/RX, packets — the number of packets sent/received on the connected device;
• Data TX/RX, bytes — the number of data bytes sent/received on the connected device;
• Data TX/RX, packets — the number of data packets sent/received on the connected device;
• Fails, packets — the number of packets sent with errors on the connected device;
• TX Period Retry, packets — the number of retries of transmission to the connected device in the last 10 seconds;
• TX Retry Count, packets — the number of retries of transmission to the connected device during the entire connection;
• Actual TX/RX Rate, Kbps — the current traffic transmission rate at the moment.

The "WDS" submenu

The WDS submenu displays information about the status of WEP-2L access points connected via WDS.

• # — number of the connected device in the list;
• Hostname — device network name;
• IP Address — IP-address of the connected device;
• MAC — MAC address of the connected device;
• Interface — interface of WEP-2L and the connected device interaction;
• Link Capacity — parameter that displays efficiency of modulation to transmission use by access point. Calculated based on the number of packets transmitted on each modulation to the client, and the reduction factors. Maximum value — 100% (means that all packets are transmitted to the client at maximum modulation for the maximum nss type supported by the client). Minimum value — 2% (in case when packets are transmitted on nss1mcs0 modulation for a client with 3x3 MIMO support). The parameter value is calculated over the last 10 seconds;
• Link Quality — parameter that displays the state of the link to the client, calculated based on the number of packet retransmissions sent to the client. Maximum value — 100% (all transmitted packets were sent on the first attempt), minimum value — 0% (no packet to the client was successfully sent). The parameter value is calculated over the last 10 seconds;
• Link Quality Common — parameter that displays the state of the link to the client, calculated based on packet retransmission sent to the client. Maximum value — 100% (all transmitted packets were sent on the first attempt), minimum value — 0% (no packet to the client was successfully sent). The parameter value is calculated for the entire time of the client connection; 
• RSSI — received signal level, dBm;
• SNR — ratio signal/noise, dB;
• TxRate — channel transmission rate, Mbps;
• RxRate — receive channel rate, Mbps;
• TX BW — transmission bandwidth, MHz;
• RX BW — reception bandwidth, MHz;
• Uptime — Wi-Fi client connection uptime.

To display more detailed information on a particular client, select it from the list. A detailed description includes the following options: 

• Total TX/RX, bytes — the number of bytes sent/received on the connected device;
• Total TX/RX, packets — the number of packets sent/received on the connected device;
• Data TX/RX, bytes — the number of data bytes sent/received on the connected device;
• Data TX/RX, packets — the number of data packets sent/received on the connected device;
• Fails, packets — the number of packets sent with errors on the connected device;
• TX Period Retry, packets — the number of retries of transmission to the connected device in the last 10 seconds;
• TX Retry Count, packets — the number of retries of transmission to the connected device during the entire connection;
• Actual TX/RX Rate, Kbps — the current traffic transmission rate at the moment.

The “Traffic Statistics” submenu

The “Traffic Statistics” section displays the diagrams of the speed of the transmitted/received traffic for last 3 minutes, as well as statistics on the amount of transmitted/received traffic since the access point was turned on.

The LAN Tx/Rx diagram shows the speed of the transmitted/received traffic via the access point's Ethernet interface in the last 3 minutes. The diagram is automatically updated every 6 seconds.

The WLAN0 and WLAN1 Tx/Rx diagrams show the last 3 minutes rate of transmitted/received traffic via Radio 2,4 GHz and Radio 5 GHz access point interfaces. The diagram is automatically updated every 6 seconds.

“Transmit” table description:

• Interface — name of the interface;
• Total packets — number of successfully sent packets;
• Total bytes — number of successfully sent bytes;
• Total drop — number of rejected packets;
• Errors — number of errors.

“Receive” table description:

• Interface — name of the interface;
• Total packets — number of successfully received packets;
• Total bytes — number of successfully received bytes;
• Total drop — number of rejected packets;
• Errors — number of errors.

The “Scan Environment” submenu

In the “Scan Environment” submenu, scanning of the surrounding radio is carried out and detection of neighboring access points.

After clicking on the “Scan” button, the process will be launched. After the scan is completed, a list of detected access points and information about them will appear:

• Range — specifies the range of 2.4 GHz or 5 GHz to which the access point was detected;
• SSID — SSID of the detected access point;
• Security Mode — security mode of the detected access point;
• MAC — MAC address of the detected access point;
• Channel/Bandwidth — radio channel on which the detected access point operates;
• RSSI — the level with which the device receives the signal of the detected access point, dBm.

The “Events” submenu

In this section, you can view a list of real-time informational messages which contains the following information:

• Date and Time — time when event was generated;
• Type — category and importance level of the event;
• Service — name of the process that generated the message;
• Message — event description.

Table 7 — event importance categories description

To receive new messages in the event log, click the “Update” button.

If necessary, you can delete all old messages from the log by clicking on the “Clear” button.

The “Network Information” submenu

In the “Network Information” submenu you can view common network settings of the device.

WAN Status:

• Interface — name of the bridge interface;
• Protocol — a protocol which is used for access to WAN;
• IP address — device IP address in external network;
• RX Bytes — number of bytes received on WAN;
• TX Bytes — number of bytes sent from WAN.

Ethernet:

• Link Status — Ethernet port status;
• Speed — Ethernet port connection speed;
• Duplex — data transfer mode:
  • Full — full duplex;
  • Half — half-duplex.

ARP
The ARP table contains information about the alignment between the IP and MAC addresses of neighboring network devices:

• IP address — device IP address;
• MAC — device MAC address.

Routes:

• Interface — name of the bridge interface;
• Destination — IP address of destination host or subnet that the route is established to;
• Gateway — gateway IP address that allows for the access to the Destination;
• Netmask — subnet mask;
• Flags — certain route characteristics. The following flag values exist:
  • U — means that the route is created and passable;
  • H — identifies the route to the specific host;
  • G — means that the route lies through the external gateway. System network interface provides routes in the network with direct connection. All other routes lie through the external gateways. G flag is used for all routes except for the routes in the direct connection networks;
  • R — indicates that the route was most likely created by a dynamic routing protocol running on the local system using the reinstate parameter;
  • D — indicates that the route was added as a result of receiving an ICMP Redirect Message. When the system learns the route from the ICMP Redirect message, the route will be added into the routing table in order to exclude redirection of the following packets intended for the same destination;
  • M — means that the route was modified — likely by a dynamic routing protocol running on a local system with the “mod” parameter applied;
  • A — points to a buffered route to which an entry in the ARP table corresponds;
  • C — means that the route source is the core routing buffer;
  • L — indicates that the destination of the route is one of the addresses of this computer. Such “local routes” exist in the routing buffer only;
  • B — means that the route destination is a broadcasting address. Such “broadcast routes” exist in the routing buffer only;
  • I — indicates that the route is connected to a ring (loopback) interface for a purpose other than to access the ring network. Such “internal routes” exist in the routing buffer only;
  • ! — means that datagrams sent to this address will be rejected by the system.

The “Radio Information” submenu

In the  “Radio Information”  submenu the current status of WEP-2L radio interfaces is displayed.

The access point radio interfaces can be in two states: “On” and “Off”. The status of each radio interface is shown in the “Status” field.

The Radio status depends on whether the radio interface has virtual access points (VAPs) or WDS enabled. In case there is at least one active VAP on the radio interface, Radio will be in “On” status, otherwise — “Off”.

Depending on the Radio status, the following information is available for monitoring:

“Off”:

• Status — radio interface state;
• MAC — radio interface MAC address;
• Mode — radio interface operation mode according to IEEE 802.11 standards.

“On”:

• Status — radio interface state;
• MAC — radio interface MAC address;
• Mode — radio interface operation mode according to IEEE 802.11 standards;
• Channel — number of the wireless channel on which the radio interface is running;
• Channel bandwidth — bandwidth of the channel on which the radio interface is running.

The “Device Information” submenu

The “Device Information” submenu displays main WEP-2L parameters.

• Product — device model name;
• Hardware Version — device hardware version;
• Factory MAC Address — device WAN interface MAC address, setted by manufacturer;
• Serial Number — device serial number, setted by manufacturer;
• Firmware Version — device firmware version;
• Backup Version — previously installed firmware version;
• Boot Version — device firmware boot version;
• System Time — current time and date, setted in system;
• Uptime — the time since the last turn on or restart the device.

The “Radio” menu

In the “Radio” menu you can configure the wireless interface.

The “Radio 2.4 GHz” submenu

In the “Radio 2.4 GHz” submenu you can configure the main parameters of the radio interface of the device operating in the 2.4 GHz band.

• Mode — select interface operation mode:
  • IEEE 802.11b/g
  • IEEE 802.11b/g/n
  • IEEE 802.11n
• Auto Channel — when checked, the device will automatically select the least loaded radio channel for the Wi-Fi interface. Removing the flag opens the access to install the static operation channel;
• Channel — select channel for data transmission;
• Use Limit Channels — when checked, the access point will use a user-defined list of channels to work in automatic channel selection mode. If the “Use Limit Channels” flag is not checked or there are no channels in the list, the access point will select the operation channel from all available channels in the given band. 2.4 GHz range channels: 1-13;
• Channel Bandwidth, MHz — channel bandwidth, on which the access point operates. The parameter may take values of 20 and 40 MHz;
• Primary Channel — the parameter can only be changed if the bandwidth of a statically specified channel is equal to 40 MHz. The 40 MHz channel can be considered as consisting of two 20 MHz channels, which border in the frequency range. These two 20 MHz channels are called primary and secondary channels. The primary channel is used by clients who only support 20 MHz channel bandwidth:
  • Upper — the primary channel will be the upper 20 MHz channel in the 40 MHz band;
  • Lower — the primary channel will be the lower 20 MHz channel in the 40 MHz band;
• Transmission Power Limit, dBm — transmitting Wi-Fi signal power adjustment, dBm. May take values between 11 and 16 dBm;
• Fixed Transmit Rate — fixed wireless data transmission rate which is defined by IEEE 802.11b/g/n standards.

In the “Advanced” section, you can configure advanced device’s radio interface parameters.

• OBSS Coexistence — automatic channel bandwidth reduction when the air is loaded. When the flag is set, the mode is enabled;
• Short Guard interval — support for Short Guard interval. Access point transmits data using 400 ns Guard interval (instead of 800 ns) to clients which also support Short GI;
• STBC — Soace-Time Block Coding method dedicated to improve data transmission reliability. The field is available only if the selected mode of operation of the radio interface includes 802.11n. When checked, the device transmits one data flow through several antennas. When unchecked, the device does not transmit one data flow through several antennas;
• Beacon Interval, ms — beacon frames transmission period. The frames are sent to detect access points. The parameter takes values from 20 to 2000 ms, by default — 100 ms;
• Fragmentation Threshold — frame fragmentation threshold, bytes. The parameter takes values 256-2346, by default — 2346;
• RTS Threshold — after what quantity of bytes the Request to Send will be sent. Decreasing of the parameter's value might improve access point operation when there are a lot of clients connected. However, decreasing of the parameter's value will reduce general bandwidth of wireless network. The parameter takes values from 0 to 2347, by default — 2347;
• Aggregation — enable support for AMPDU/AMSDU;
• Short Preamble — use of the packet short preamble;
• Broadcast/Multicast Rate Limiting, p/s — when the flag is set, transmission of broadcast / multicast traffic over the wireless network is restricted. Specify the limit for broadcast traffic in the popup window (p/s);
• Wi-Fi Multimedia (WMM) — WMM support activation (Wi-Fi Multimedia);
• Enable QoS — when the flag is set, the setting of Quality of Service functions is available.

The following functions are available for quality assurance configuration:

• AP EDCA parameters — access point settings table (traffic is transmitted from the access point to the client):
  • Queue — predefined queues for various kinds of traffic:
    • Data 3 (Background) — low priority queue, high bandwidth (802.1p: cs1, cs2 priorities);
    • Data 2 (Best Effort) — middle priority queue, middle bandwidth and delay; Most of the traditional IP data is sent to this queue (802.1p: cs0, cs3 priorities);
    • Data 1 (Video) — high priority queue, minimal delay. In this queue, time-sensitive video data is automatically processed (802.1p: cs4, cs5 priorities);
    • Data 0 (Voice) — high priority queue, minimal delay. In this queue, time sensitive data is automatically processed, such as: VoIP, streaming video (802.1p: cs6, cs7 priorities).
  • AIFS — Arbitration Inter-Frame Spacing, defines the waiting time of data frames, measured in slots, takes values (1-255);
  • cwMin — the initial timeout value before resending a frame, specified in milliseconds, takes the values 1, 3, 7, 15, 31, 63, 127, 255, 511, 1023. The value of cwMin cannot exceed the value of cwMax;
  • cwMax — the maximum timeout value before resending a frame, specified in milliseconds, takes the values 1, 3, 7, 15, 31, 63, 127, 255, 511, 1023. The value of cwMax must exceed the value of cwMin;
  • TXOP Limit — this parameter is used only for data transmitted from the client station to the access point. The transmission capability is the time interval, in milliseconds, when the client WME station has the rights to initiate data transmission over the wireless medium to the access point, the maximum value is 65535 milliseconds;
• Station EDCA parameters — table of client station parameter settings (traffic is transmitted from the client station to the access point). For description of table fields, see above.

To apply a new configuration and save setting to non-volatile memory, press “Apply”. Press “Cancel” to discard the changes.

The “Radio 5 GHz” submenu

In the “Radio 5 GHz” submenu you can configure the main parameters of the radio interface of the device operating in the 5 GHz band.

• Mode — select interface operation mode:
  • IEEE 802.11a;
  • IEEE 802.11a/n;
  • IEEE 802.11a/n/ac.
• Auto Channel — when checked, the device will automatically select the least loaded radio channel for the Wi-Fi interface. Removing the flag opens the access to install the static operation channel;
• Channel — select channel for data transmission;
• Use Limit Channels — when checked, the access point will use a user-defined list of channels to work in automatic channel selection mode. If the “Use Limit Channels” flag is not checked or there are no channels in the list, the access point will select the operation channel from all available channels in the given band. 5 GHz range channels: 36-64, 132-144, 149-165;
• Channel Bandwidth, MHz — channel bandwidth, on which the access point operates. The parameter may take values of 20, 40 and 80 MHz;
• Primary Channel — the parameter can only be changed if the bandwidth of a statically specified channel is equal to 40 MHz. The 40 MHz channel can be considered as consisting of two 20 MHz channels, which border in the frequency range. These two 20 MHz channels are called primary and secondary channels. The primary channel is used by clients who only support 20 MHz channel bandwidth:
  • Upper — the primary channel will be the upper 20 MHz channel in the 40 MHz band;
  • Lower — the primary channel will be the lower 20 MHz channel in the 40 MHz band.
• Transmission Power Limit, dBm — transmitting Wi-Fi signal power adjustment, dBm. May take values between 11 and 19 dBm;
• Fixed Transmit Rate — fixed wireless data transmission rate which is defined by IEEE 802.11a/n/ac standards.

In the “Advanced” section, you can configure advanced device’s radio interface parameters.

• OBSS Coexistence — automatic channel bandwidth reduction when the air is loaded. When the flag is set, the mode is enabled;
• DFS Support — dynamic frequency selection mechanism. The mechanism demands wireless devices to scan environment and avoid using channels which coincide with radiolocation system's channels at 5 GHz:
  • Disabled — the mechanism is disabled. DFS channels are not available for selection;
  • Enabled — the mechanism is enabled;
  • Forced — the mechanism is disabled. DFS channels are available for selection.
• Short Guard interval — support for Short Guard interval. Access point transmits data using 400 ns Guard interval (instead of 800 ns) to clients which also support Short GI;
• STBC — Soace-Time Block Coding method dedicated to improve data transmission reliability. The field is available only if the selected mode of operation of the radio interface includes 802.11n. When checked, the device transmits one data flow through several antennas. When unchecked, the device does not transmit one data flow through several antennas;
• Beacon Interval, ms — beacon frames transmission period. The frames are sent to detect access points. The parameter takes values from 20 to 2000 ms, by default — 100 ms;
• Fragmentation Threshold — frame fragmentation threshold, bytes. The parameter takes values 256-2346, by default — 2346;
• RTS Threshold — after what quantity of bytes the Request to Send will be sent. Decreasing of the parameter's value might improve access point operation when there are a lot of clients connected. However, decreasing of the parameter's value will reduce general bandwidth of wireless network. The parameter takes values from 0 to 2347, by default — 2347;
• Aggregation — enable support for AMPDU/AMSDU;
• Short Preamble — use of the packet short preamble;
• Broadcast/Multicast Rate Limiting, p/s — when the flag is set, transmission of broadcast / multicast traffic over the wireless network is restricted. Specify the limit for broadcast traffic in the popup window (p/s);
• Wi-Fi Multimedia (WMM) — WMM support activation (Wi-Fi Multimedia);
• Enable QoS — when the flag is set, the setting of Quality of Service functions is available.

The following functions are available for quality assurance configuration:

• AP EDCA parameters — access point settings table (traffic is transmitted from the access point to the client):
  • Queue — predefined queues for various kinds of traffic:
    • Data 3 (Background) — low priority queue, high bandwidth (802.1p: cs1, cs2 priorities);
    • Data 2 (Best Effort) — middle priority queue, middle bandwidth and delay. Most of the traditional IP data is sent to this queue (802.1p: cs0, cs3 priorities);
    • Data 1 (Video) — high priority queue, minimal delay. In this queue, time-sensitive video data is automatically processed (802.1p: cs4, cs5 priorities);
    • Data 0 (Voice) — high priority queue, minimal delay. In this queue, time sensitive data is automatically processed, such as: VoIP, streaming video (802.1p: cs6, cs7 priorities).
  • AIFS — Arbitration Inter-Frame Spacing, defines the waiting time of data frames, measured in slots, takes values (1-255);
  • cwMin — the initial timeout value before resending a frame, specified in milliseconds, takes the values 1, 3, 7, 15, 31, 63, 127, 255, 511, 1023. The value of cwMin cannot exceed the value of cwMax;
  • cwMax — the maximum timeout value before resending a frame, specified in milliseconds, takes the values 1, 3, 7, 15, 31, 63, 127, 255, 511, 1023. The value of cwMax must exceed the value of cwMin;
  • TXOP Limit — this parameter is used only for data transmitted from the client station to the access point. The transmission capability is the time interval, in milliseconds, when the client WME station has the rights to initiate data transmission over the wireless medium to the access point, the maximum value is 65535 milliseconds;
• Station EDCA parameters — table of client station parameter settings (traffic is transmitted from the client station to the access point). For description of table fields, see above.

To apply a new configuration and save setting to non-volatile memory, press “Apply”. Press “Cancel” to discard the changes.

The “Advanced” submenu

In the “Advanced” section, you can configure advanced device’s radio interface parameters.

• Global Isolation — when checked, traffic isolation between clients of different VAP and different radio interfaces is enabled.

To apply a new configuration and save setting to non-volatile memory, press “Apply”. Press “Cancel” to discard the changes.

The “VAP” menu

In the “VAP” menu, you can configure virtual Wi-Fi access points (VAP).

The “Summary” submenu

The “Summary” submenu displays the settings of all VAPs on Radio 2.4 GHz and Radio 5 GHz radio interfaces. You can see the settings of each virtual access point in sections VAP0..3.

• VAP0..3 — the sequence number of the virtual access point;
• Enabled — when checked, the virtual access point is enabled, otherwise it is disabled;
• Security Mode — the type of data encryption used on the virtual access point;
• VLAN ID — VLAN number from which the tag will be removed when transmitting Wi-Fi traffic to clients connected to this VAP. When traffic flows in the opposite direction, untagged traffic from clients will be tagged with VLAN ID (when VLAN Trunk mode is disabled);
• SSID — virtual wireless network name;
• Band Steer mode — when the flag is set, SSID broadcasting is on, otherwise it is disabled;
• Broadcast SSID — when checked, SSID broadcasting is on, otherwise it is disabled;
• VLAN Trunk — when the flag is set, tagged traffic is transmitted to the subscriber;
• General Mode — when the flag is set, transmission of untagged traffic jointly with tagged traffic is allowed (available when Trunk VLAN mode is enabled);
• General VLAN ID — a tag will be removed from the specified VLAN ID and the traffic of this VLAN will pass to the client without a tag. When traffic passes in the opposite direction, untagged traffic will be tagged with General VLAN ID;
• Station Isolation– when checked, traffic isolation between clients in the same VAP is enabled.

To apply a new configuration and save setting to non-volatile memory, press “Apply”. Press “Cancel” to discard the changes.

The “VAP” submenu

Common settings

• Enabled — when checked, the virtual access point is enabled, otherwise it is disabled;
• VLAN ID — VLAN number from which the tag will be removed when transmitting Wi-Fi traffic to clients connected to this VAP. When traffic flows in the opposite direction, untagged traffic from clients will be tagged with VLAN ID (when VLAN Trunk mode is disabled);
• SSID — virtual wireless network name;
• Broadcast SSID — when checked, SSID broadcasting is on, otherwise it is disabled;
• Band Steer mode — when the flag is set, the client's priority connection to the 5 GHz network is active. For the function to work, create a VAP with the same SSID on each radio interface, and activate the “Band Steer” parameter on them; 
• VLAN Trunk — when the flag is set, tagged traffic is transmitted to the subscriber;
• General Mode — when the flag is set, transmission of untagged traffic jointly with tagged traffic is allowed (available when Trunk VLAN mode is enabled);
• General VLAN ID — a tag will be removed from the specified VLAN ID and the traffic of this VLAN will pass to the client without a tag. When traffic passes in the opposite direction, untagged traffic will be tagged with General VLAN ID;
• Station Isolation — when checked, traffic isolation between clients in the same VAP is enabled;
• Support for 802.11k/v — enable support for 802.11k/v standards on virtual access point;
• Priority — select prioritization means. Defines the field on the basis of which the traffic transmitted to the radio interface will be distributed in WMM queues:
  • DSCP — will analyze the priority from the DSCP field of the IP packet header;
  • 802.1p — will analyze the priority from the CoS (Class of Service) field of the tagged packets.
• Maximum Stations — the maximum number of clients connected to the virtual network;
• Minimal Signal — signal level in dBm below which the client equipment is disconnected from the virtual network;

• Security Mode — wireless access security mode:
  • Off — do not use encryption for data transfer. The access point is available for any subscriber to connect;
  • WPA, WPA2, WPA/WPA2 — encryption methods, if you select one of the methods, the following setting will be available:
    • WPA Key — key/password required to connect to the virtual access point. The length of the key makes from 8 to 63 characters;
  • WPA-Enterprise, WPA2-Enterprise, WPA/WPA2-Enterprise — wireless channel encryption mode, in which the client is authorized on the centralized RADIUS server. To configure this security mode, you must specify the parameters of the RADIUS server. You also need to specify a key for the RADIUS server. If you select one of the methods, the following setting will be available:
    • Domain — user domain;
    • IP Address of RADIUS Server — RADIUS server address;
    • Port of RADIUS Server– port of the RADIUS server that used for authentication and authorization;
    • Password of RADIUS Server — password for the RADIUS server used for authentication and authorization;
    • Use Accounting through RADIUS — when checked, “Accounting” messages will be sent to the RADIUS server;
    • Use Other Settings For Accounting:
      • IP Address of RADIUS Server for Accounting — address of the RADIUS server, used for accounting;
      • Password of RADIUS Server for Accounting– password for the RADIUS server used for accounting.
    • Port of RADIUS Server for Accounting — port that will be used to collect accounts on the RADIUS server:
      • Use Periodic Accounting — enable periodic sending of “Accounting” messages to the RADIUS server. You can set the interval for sending messages in the “Accounting Interval” field.

Captive Portal

Under security modes: Off, WPA, WPA2, WPA/WPA2 a portal authorization setting is available on the VAP.

• Enable — when checked, authorization of users in the network will be performed via the virtual portal;
• Virtual Portal Name — name of the virtual portal to which the user will be redirected when connecting to the network;
• Redirect URL — the address of the external virtual portal to which the user will be redirected when connecting to the network.

RADIUS

• Use Accounting through RADIUS — when checked, “Accounting” messages will be sent to the RADIUS server;
• Domain — user domain;
• IP Address of RADIUS Server for Accounting — address of the RADIUS server, used for accounting;
• Port of RADIUS Server for Accounting — port that will be used to collect accounts on the RADIUS server;
• Password of RADIUS Server for Accounting — password for the RADIUS server used for accounting;
• Use Periodic Accounting — enable periodic sending of “Accounting” messages to the RADIUS server. You can set the interval for sending messages in the “Accounting Interval” field.

Shapers

• Show — display configuration field;
• VAP Limit Down — restriction of bandwidth in the direction from the access point to the clients (in total) connected to this VAP, Kbps;
• VAP Limit Up — restriction of bandwidth in the direction from the clients (in total) connected to this VAP, to the access point, Kbps;
• STA Limit Down — restriction of bandwidth in the direction from the access point to the clients (each separately) connected to this VAP, Kbps;
• STA Limit Up — restriction of bandwidth in the direction from the clients (each separately) connected to this VAP, to the access point, Kbps.

To apply a new configuration and save setting to non-volatile memory, press “Apply”. Press “Cancel” to discard the changes.

The “WDS” menu

In the WDS menu you can configure wireless bridges between WEP-2L.

The “WDS” submenu

In the "2.4 GHz" and "5 GHz" tabs you can select the radio interface of the device on which you want to build a wireless bridge.

• Enabled — when flag is set, WDS mode is enabled, otherwise it is disabled;
• Security Mode — security access mode to the wireless network;
  • Off — do not use encryption for data transmission;
  • WPA, WPA2 — encryption method, when selected, the following setting will be available:
    • WPA key — key/password neccessary for connection to to the oncoming access point. Key length is from 8 to 63 characters.
• Interface — select and enable the WDS interface on which the wireless bridge will be built;
• MAC — radio interface MAC address of oncoming device, to which the wireless bridge will be built. Radio interface MAC address can be viewed in web interface of oncoming device in tab "Monitoring"/"Radio Information". To configure WDS to Radio 2.4 GHz, you need to specify the MAC address of the Radio 2.4 GHz of the oncoming device. The configuration of the WDS interface on Radio 5 GHz is performed the same way — the MAC address of the Radio 5 GHz of the oncoming device is indicated;
• Fixed Transmit Rate — fixed wireless data transmission rate which is defined by IEEE 802.11b/g/n standards.

To apply a new configuration and save setting to non-volatile memory, click “Apply”. Click “Cancel” to discard the changes.

The “Network Settings” menu

The “System Configuration” submenu

• Hostname — nertwork name of the device, specified by string from 1 to 63 characters; latin uppercase and lowercase letters, numbers, hyphen “-” (hyphen can not be the last character in the name);
• AP Location — domain of the EMS management system tree host where the access point is located;
• Management VLAN:
  • Disabled — Management VLAN is not used;
  • Terminating — the mode in which the management VLAN is terminated at the access point; in this case, clients connected via the radio interface do not have access to this VLAN. When WDS is configured, this VLAN mode is unavailable for selection;
  • Forwarding — the mode in which the management VLAN is also transmitted to the radio interface (with the appropriate VAP configuration).
• VLAN ID — the VLAN ID used to access the device, takes values 1-4094;
• Protocol — select protocol for connection of the device via Ethernet interface to service provider network:
  • DHCP — operation mode, when IP address, subnet mask, DNS server address, defualt gateway and other parameters required for operation are obtained from DHCP server automatically;
  • Static — operation mode where IP address and all the necessary parameters for WAN interface are assigned statically. If “Static” is selected, the following parameters will be available to set:
    • Static IP — device WAN interface IP address in the provider network;
    • Netmask — external subnet mask;
    • Gateway — address, to which the packet is sent, if the route in routing table is not found for it.
  • Primary DNS server, Secondary DNS server — IP address of DNS servers. If DNS servers' addresses are not allocated automatically via DHCP, set them manually.

To apply a new configuration and save setting to non-volatile memory, press “Apply”. Press “Cancel” to discard the changes.

The “Access” submenu

In the “Access” submenu, you can configure access to the device via the Web interface, Telnet, SSH, NETCONF and SNMP.

• To enable access to the device via the web interface via HTTP protocol, set the flag next to “WEB”. In the window that appears, it is possible to change the HTTP port (by default, 80). The range of acceptable values of ports, in addition to the default, from 1025 to 65535 inclusive;
• To enable access to the device via the web interface via HTTPS protocol, set the flag next to “WEB-HTTPS”. In the window that appears, it is possible to change the HTTPS port (by default, 443). The range of acceptable values of ports, in addition to the default, from 1025 to 65535 inclusive;

  
  

  Note that the ports for the HTTP and HTTPS protocols should not have the same value.

  
  

WEP-2L software allows monitoring status of the device and it's sensors via SNMP. In the SNMP submenu, you can configure settings of SNMP agent. The device supports SNMPv1 and SNMPv2 protocol version.

To change the SNMP settings, check the box next to “SNMP”, apply the configuration and then go to the SNMP submenu.

• roCommunity — a password to read the parameters (by default: public);
• rwCommunity — a password to configure (write) parameters (by default: private);
• TrapSink — IP address or domain name of SNMPv1-trap message recipient in HOST [COMMUNITY [PORT]] format;
• Trap2Sink — IP address or domain name of SNMPv2-trap message recipient in HOST [COMMUNITY [PORT]] format;
• InformSink — IP address or domain name of Inform message recipient in HOST [COMMUNITY [PORT]] format;
• Sys Name — device name;
• Sys Contact — device vendor contact information;
• Sys Location — device location information;
• Trap community — password enclosed in traps (default value: trap).

The list of objects which are supported for reading and configuration via SNMP is given below:

• eltexLtd.1.127.1 — monitoring access point parameters and connected client devices;
• eltexLtd.1.127.3 — access point management (reboot).

where eltexLtd — 1.3.6.1.4.1.35265 is Eltex Enterprise ID.

To apply a new configuration and save setting to non-volatile memory, press “Apply”. Press “Cancel” to discard the changes.

The “External Services” menu

The “Captive Portal” submenu

The “Captive Portal” submenu is designed to enable and configure the APB service at the access point.

The APB service is used to provide portal roaming of clients between access points connected to the service.

• Enable — when checked, the point will connect to the APB service, the address of which is specified in the “Roaming Service URL” field, to provide portal roaming of clients;
• Roaming Service URL — APB service address to support roaming in the portal authorization mode. Set in format: "ws://<host>:<port>/apb/broadcast".

To apply a new configuration and save setting to non-volatile memory, click “Apply”. Click “Cancel” to discard the changes.

The “System” menu

In the “System” menu you can configure system, time, device access via different protocols, change password and update device firmware.

The “Device Firmware Upgrade” submenu

The “Device Firmware Upgrade” submenu is intended for upgrading the device's firmware.

• Active Version — installed firmware version, which is operating at the moment;
• Backup version — installed firmware version which can be used in case of problems with the current active firmware version;
  • Set active — a button that allows you to make a backup version of the firmware active, this will require a reboot of the device. The active firmware version will not be set as a backup.

Firmware update

Download the firmware file from http://eltex-co.com/support/downloads/ and save it on your computer. To do this, click the “Browse” button in the Firmware Image field and specify the path to the firmware file in .tar.gz format.
To start the update process, you must click the “Start Upgrading” button. The process may take several minutes (its current status will be shown on the page). The device will be automatically rebooted when the update is completed.

The “Configuration” submenu

In the “Configuration” submenu you can save and update current configuration.

Backup Configuration

To save current device configuration to local computer click on the “Download” button.

Restore Configuration

To download the configuration file saved on the local computer, use the Restore Configuration item. To update the device configuration click the “Browse” button, specify a file (in .tar.gz format) and click the “Upload” button. Uploaded configuration will be applied automatically and does not require device reboot.

To change the passwords open the configuration file in text editor and change passwords. Then save the changes in configuration archive. The example of password changing is shown below:

Reset to Default Configuration

To reset all the settings to default values, press “Reset” button. If the flag “Save access setting” is activated, then those settings, configurations that are responsible for access to the device (IP address settings, Telnet/SSH/SNMP/Netconf/Web access settings) will be saved

The “Reboot” submenu

To reboot the device, click on the “Reboot” button. The device reboot process takes about 1 minute.

The “Password” submenu

When logging in via web interface administrator (default password: password) has the full access to the device: read/write any settings, full device status monitoring.
To change the password, enter the new password first in the “Password” field, then in the “Confirm Password” field and click the “Apply” button to save the new password.

The “Log” submenu

The “Log” submenu is designed to configure the output of various kinds of debugging messages of the system in order to detect the causes of problems in the operation of the device. 

• Mode — Syslog agent operation mode:
  • Local File — log information is stored in a local file and is available in the device’s web interface on the “Monitoring/Events” tab;
  • Server and File — log information is sent to a remote Syslog server and stored in a local file.
• Syslog Server Address — IP address or domain name of the Syslog server;
• Syslog Server Port — port for incoming Syslog server messages (default: 514, valid values: from 1 to 65535);
• File Size, KiB — maximum size of the log file (valid values: 1-1000 kB).

To apply a new configuration and save setting to non-volatile memory, click “Apply”. Click “Cancel” to discard the changes.

The “Date and Time” submenu

In the “Date and Time” submenu, you can set the time manually or using the time synchronization protocol (NTP).
Manual

• Date and Time device — date and time set on the device. Click on the “Edit” button if the correction is necessary;
  • Date, Time — set the current date and time or click the “Set current date and time” button to synchronize with the device.
• Time Zone — allows to set the timezone according to the nearest city for your region from the list;
• Daylight Saving Time Enable — when selected, automatic daylight saving change will be performed automatically within the defined time period:
  • DST Start — day and time, when daylight saving time is starting;
  • DST End — day and time, when daylight saving time is ending;
  • DST Offset (minutes) — time period in minutes, on which time offset is performing. May take values from 0 to 720 minutes.

NTP Server

• Date and Time device — date and time set on the device;
• NTP Server — time synchronization server IP address/domain name. You can specify an address or select from an existing list;
• Time Zone — allows to set the timezone according to the nearest city for your region from the list;
• Daylight Saving Time Enable — when selected, automatic daylight saving change will be performed automatically within the defined time period:
  • DST Start — day and time, when daylight saving time is starting;
  • DST End — day and time, when daylight saving time is ending;
  • DST Offset (minutes) — time period in minutes, on which time offset is performing.

To apply a new configuration and store settings into the non-volatile memory, click the “Apply” button. To discard changes click the “Cancel” button.

Managing the device using the command line

Connection to the device

By default, WEP-2L is configured to receive the address via DHCP. If this does not happen, you can connect to the device using the factory IP address.

Connection to the device is performed via SSH/Telnet:

Network parameters configuration

Network parameters configuration via set-management-vlan-mode utility

IPv6 network parameters configuration

Virtual Wi-Fi access points (VAP) configuration

When configuring a VAP, remember that the interface names in the 2.4 GHz range start with wlan0, in the 5 GHz range with wlan1.

Table 8 — Commands for configuration of security mode on VAP

Below are examples of VAP configuration with different security modes for Radio 5 GHz (wlan1).

Configuration of VAP without encryption

Configuration of VAP with WPA-Personal security mode

Configuration of VAP with Enterprise authorization

Configuration of VAP with Captive Portal

Advanced VAP settings

802.11r configuration

This type of roaming is available only for customers' devices supporting 802.11r.

802.11r roaming is possible only between VAP with WPA2-Personal and WPA2-Enterprise security modes.

VAP configuration with WPA2-Personal security mode manual and others can be seen in section Configuration of VAP with WPA-Personal security mode.

Each VAP on the access points should be configured individually, eg. AP1(wlan1)↔AP2(wlan1), AP1(wlan0)↔AP2(wlan0), AP1(wlan1)↔AP3(wlan1), etc.

Below is the example of 802.11r configuring on two access points: AP1 and AP2.

802.11k configuration

802.11k protocol roaming can be organized between any network (open/secure). If the access point is configured to work under the 802.11k protocol, then when a customer connects, the access point sends them the list of “friendly” access points to which a customer can switch in a roaming process. The list contains information about access points' MAC addresses and channels they work with.

Use of 802.11k allows to reduce the time that the spends looking for another network when roaming, since the customer does not need to scan channels on which there are no target access points available for switching.

This type of roaming is available only for customers' devices supporting 802.11k.

Below is the example of 802.11k configuring access point — making a list of “friendly” access points.

Radio settings

In the Radio section, automatic selection of the working channel is used by default. To set the channel manually and change the power, use the following commands:

Advanced Radio settings

The configuration method of edca-sta is the same as that of edca-ap.
Parameters configuration for queues be, vi, vo is similar to parameters configuration for queue bk.

WDS configuring

Configuring WDS connection on Radio 5 GHz interface (wlan1) is given below.

System settings

Device firmware update

Device configuration management

Device reboot

Setting the date and time

Advanced system settings

APB service configuration

The APB service is used to provide portal roaming of clients between access points connected to the service. 

Monitoring

Wi-Fi Clients

To display monitoring of connected Wi-Fi clients, use the command:

To display a list of clients connected to the access point, press Tab after monitoring associated-clients.

32:5b:60:62:e0:a4
bc:2e:f6:cc:85:46
all

To get a list of monitoring parameters, press Tab after filter.

index
interface
ssid
hw-addr
state
ip-addr
hostname
rx-retry-count
tx-fails
tx-period-retry
tx-retry-count
..... 

 index                    | 0
 interface                | wlan1-va0
 state                    | ASSOC SLEEP AUTH_SUCCESS 
 hw-addr                  | 32:5b:60:62:e0:a4
 ssid                     | 2ac-open
 ip-addr                  | 10.24.80.58
 authorized               | true
 captive-portal-vap       | false
 enterprise-vap           | false
 rx-retry-count           | 161
 tx-fails                 | 0
 tx-period-retry          | 3
 tx-retry-count           | 626
 rssi-1                   | -20
 rssi-2                   | -20
 snr-1                    | 14
 snr-2                    | 14
 tx-rate                  | MCS15 NO SGI 270
 rx-rate                  | MCS15 NO SGI 130
 rx-bw                    | 20M
 rx-bw-all                | 20M
 tx-bw                    | 40M
 uptime                   | 00:01:32
 multicast-groups-count   | 1
 wireless-mode            | n
 perftest-capable         | false
 snr-rssi-capable         | false
 link-capacity            | 100
 link-quality             | 99
 link-quality-common      | 96
 actual-tx-rate           | 449
 actual-rx-rate           | 30
 shaped-rx-rate           | 32
 actual-tx-pps            | 49
 actual-rx-pps            | 29
 shaped-rx-pps            | 29
 name                     | 0

 Rate                  Transmitted            Received                 
---------------------------------------------------------------------
 Total Packets:       | 8165                 | 6387                 |
 TX success:          | 100                  |                      |
 Total Bytes:         | 8446088              | 1125301              |
 Data Packets:        | 8158                 | 6008                 |
 Data Bytes:          | 8233649              | 959850               |
 Mgmt Packets:        | 7                    | 379                  |
 Mgmt Bytes:          | 331                  | 291                  |
---------------------------------------------------------------------

 Rate                  Transmitted            Received                 
---------------------------------------------------------------------
 ofdm6                | 9              |   0%|            378 |   5%|
 mcs7                 | 2              |   0%|              0 |   0%|
 mcs11                | 0              |   0%|              3 |   0%|
 mcs12                | 28             |   0%|             66 |   1%|
 mcs14                | 1183           |  14%|              0 |   0%|
 mcs15                | 6943           |  85%|           5939 |  93%|
---------------------------------------------------------------------


Multicast groups:
 MAC                IP             
--------------------------------------
 01:00:5E:00:00:FB |     xxx.0.0.251 |
--------------------------------------


 index                    | 1
 interface                | wlan1-va2
 state                    | ASSOC AUTH_SUCCESS 
 hw-addr                  | bc:2e:f6:cc:85:46
 ssid                     | 2ac-enter
 ip-addr                  | 10.24.80.90
 hostname                 | HUAWEI_P40_Pro-81afe9c34a
 username                 | tester
 domain                   | enterprise.service.root
 authorized               | true
 captive-portal-vap       | false
 enterprise-vap           | true
 rx-retry-count           | 7
 tx-fails                 | 0
 tx-period-retry          | 1
 tx-retry-count           | 1
 rssi-1                   | -37
 rssi-2                   | -54
 snr-1                    | 11
 snr-2                    | 10
 tx-rate                  | MCS15 NO SGI 130
 rx-rate                  | MCS15 NO SGI 130
 rx-bw                    | 20M
 rx-bw-all                | 20M
 tx-bw                    | 20M
 uptime                   | 00:00:13
 multicast-groups-count   | 0
 wireless-mode            | ac
 perftest-capable         | false
 snr-rssi-capable         | false
 link-capacity            | 76
 link-quality             | 99
 link-quality-common      | 99
 actual-tx-rate           | 49
 actual-rx-rate           | 24
 shaped-rx-rate           | 23
 actual-tx-pps            | 17
 actual-rx-pps            | 20
 shaped-rx-pps            | 19
 name                     | 1

 Rate                  Transmitted            Received                 
---------------------------------------------------------------------
 Total Packets:       | 178                  | 263                  |
 TX success:          | 100                  |                      |
 Total Bytes:         | 68476                | 38913                |
 Data Packets:        | 174                  | 207                  |
 Data Bytes:          | 63720                | 32019                |
 Mgmt Packets:        | 4                    | 56                   |
 Mgmt Bytes:          | 232                  | 240                  |
---------------------------------------------------------------------

 Rate                  Transmitted            Received                 
---------------------------------------------------------------------
 ofdm6                | 21             |  11%|             33 |  12%|
 ofdm24               | 0              |   0%|             43 |  16%|
 mcs7                 | 15             |   8%|              0 |   0%|
 mcs12                | 41             |  23%|              0 |   0%|
 mcs13                | 43             |  24%|              0 |   0%|
 mcs14                | 0              |   0%|              3 |   1%|
 mcs15                | 58             |  32%|            183 |  69%|
---------------------------------------------------------------------


Multicast groups: none

 index                    | 1
 interface                | wlan1-va2
 state                    | ASSOC SLEEP AUTH_SUCCESS 
 hw-addr                  | bc:2e:f6:cc:85:46
 ssid                     | 2ac-enter
 ip-addr                  | 10.24.80.90
 hostname                 | HUAWEI_P40_Pro-81afe9c34a
 username                 | tutu
 domain                   | enterprise.service.root
 authorized               | true
 captive-portal-vap       | false
 enterprise-vap           | true
 rx-retry-count           | 9
 tx-fails                 | 0
 tx-period-retry          | 0
 tx-retry-count           | 1
 rssi-1                   | -39
 rssi-2                   | -57
 snr-1                    | 14
 snr-2                    | 13
 tx-rate                  | MCS15 NO SGI 130
 rx-rate                  | MCS15 NO SGI 130
 rx-bw                    | 20M
 rx-bw-all                | 20M
 tx-bw                    | 20M
 uptime                   | 00:01:12
 multicast-groups-count   | 0
 wireless-mode            | ac
 perftest-capable         | false
 snr-rssi-capable         | false
 link-capacity            | 100
 link-quality             | 100
 link-quality-common      | 99
 actual-tx-rate           | 1
 actual-rx-rate           | 0
 shaped-rx-rate           | 0
 actual-tx-pps            | 1
 actual-rx-pps            | 0
 shaped-rx-pps            | 0
 name                     | 1

 Rate                  Transmitted            Received                 
---------------------------------------------------------------------
 Total Packets:       | 312                  | 483                  |
 TX success:          | 100                  |                      |
 Total Bytes:         | 112678               | 55795                |
 Data Packets:        | 308                  | 295                  |
 Data Bytes:          | 104438               | 43445                |
 Mgmt Packets:        | 4                    | 188                  |
 Mgmt Bytes:          | 232                  | 240                  |
---------------------------------------------------------------------

 Rate                  Transmitted            Received                 
---------------------------------------------------------------------
 ofdm6                | 21             |   6%|            103 |  21%|
 ofdm24               | 0              |   0%|            105 |  21%|
 mcs7                 | 15             |   4%|              0 |   0%|
 mcs12                | 41             |  13%|              0 |   0%|
 mcs13                | 43             |  13%|              0 |   0%|
 mcs14                | 0              |   0%|              4 |   0%|
 mcs15                | 192            |  61%|            270 |  56%|
---------------------------------------------------------------------


Multicast groups: none

 hw-addr                  | 32:5b:60:62:e0:a4
 ip-addr                  | 10.24.80.58
 tx-rate                  | MCS15 NO SGI 270
 rx-rate                  | MCS14 NO SGI 117
 uptime                   | 00:07:57

 hw-addr                  | 32:5b:60:62:e0:a4
 rssi-1                   | -24
 rssi-2                   | -24
 wireless-mode            | n
 interface                | wlan1-va0

 hw-addr                  | bc:2e:f6:cc:85:46
 rssi-1                   | -38
 rssi-2                   | -53
 wireless-mode            | ac
 interface                | wlan1-va2

WDS

To monitor WDS connections, use the following command:

To display a list of access points with which WDS bridges are built, press Tab after monitoring wds-entries.

e8:28:c1:d1:43:15
e8:28:c1:da:cb:80
all

To get a list of monitoring parameters, press Tab after filter.

index                                                                                                                          
interface                                                                                                                      
hw-addr                                                                                                                        
state                                                                                                                          
ip-addr                                                                                                                        
hostname                                                                                                                       
rx-retry-count                                                                                                                 
tx-fails                                                                                                                       
tx-period-retry                                                                                                                
tx-retry-count                                                                                                                 
noise-1                                                                                                                        
noise-2                                                                                                                        
rssi-1                                                                                                                         
rssi-2 
..... 

 index                    | 0                                                                                                  
 interface                | wlan1                                                                                              
 state                    | WIFI_WDS                                                                                           
 hw-addr                  | e8:28:c1:d1:43:15                                                                                  
 ip-addr                  | 10.24.80.35                                                                                        
 hostname                 | WEP-2L                                                                                             
 authorized               | false                                                                                              
 captive-portal-vap       | false                                                                                              
 enterprise-vap           | false                                                                                              
 rx-retry-count           | 10                                                                                                 
 tx-fails                 | 0                                                                                                  
 tx-period-retry          | 0                                                                                                  
 tx-retry-count           | 0                                                                                                  
 rssi-1                   | -25                                                                                                
 rssi-2                   | -20                                                                                                
 snr-1                    | 40                                                                                                 
 snr-2                    | 39                                                                                                 
 wds-interface            | wlan1-wds1                                                                                         
 tx-rate                  | VHT NSS2-MCS8 SGI 173.3                                                                            
 rx-rate                  | VHT NSS2-MCS8 NO SGI 156                                                                           
 rx-bw                    | 20M                                                                                                
 rx-bw-all                | 20M                                                                                                
 tx-bw                    | 20M                                                                                                
 uptime                   | 00:02:44                                                                                           
 multicast-groups-count   | 0                                                                                                  
 wireless-mode            | ac                                                                                                 
 eltex-firmware-version   | 1.2.1 build X
 eltex-board-type         | WEP-2L                                                                                             
 perftest-capable         | false                                                                                              
 snr-rssi-capable         | false                                                                                              
 link-capacity            | 90 (not changed)                                                                                   
 link-quality             | 100 (not changed)                                                                                  
 link-quality-common      | 100                                                                                                
 actual-tx-rate           | 0                                                                                                  
 actual-rx-rate           | 5                                                                                                  
 shaped-rx-rate           | 0                                                                                                  
 actual-tx-pps            | 0                                                                                                  
 actual-rx-pps            | 8                                                                                                  
 shaped-rx-pps            | 0                                                                                                  
 name                     | 0                                                                                                  
                                                                                                                               
 Rate                  Transmitted            Received                                                                         
---------------------------------------------------------------------                                                          
 Total Packets:       | 53                   | 2125                 |                                                          
 TX success:          | 100                  |                      |                                                          
 Total Bytes:         | 4300                 | 261666               |                                                          
 Data Packets:        | 48                   | 2120                 |                                                          
 Data Bytes:          | 2496                 | 193382               |                                                          
 Mgmt Packets:        | 5                    | 5                    |                                                          
 Mgmt Bytes:          | 268                  | 444                  |                                                          
---------------------------------------------------------------------                                                          
                                                                                                                               
 Rate                  Transmitted            Received                                                                         
---------------------------------------------------------------------                                                          
 ofdm6                | 7              |  13%|             12 |   0%|                                                          
 ofdm54               | 1              |   1%|              0 |   0%|                                                          
 nss2-mcs0            | 4              |   7%|              6 |   0%|                                                          
 nss2-mcs1            | 4              |   7%|              8 |   0%|                                                          
 nss2-mcs2            | 4              |   7%|              6 |   0%|                                                          
 nss2-mcs3            | 4              |   7%|              6 |   0%|                                                          
 nss2-mcs4            | 4              |   7%|              7 |   0%|                                                          
 nss2-mcs5            | 4              |   7%|              4 |   0%|                                                          
 nss2-mcs6            | 4              |   7%|              7 |   0%|                                                          
 nss2-mcs7            | 9              |  16%|             24 |   1%|                                                          
 nss2-mcs8            | 8              |  15%|           2044 |  96%|                                                          
---------------------------------------------------------------------                                                          
                                                                                                                               
                                                                                                                               
Multicast groups: none  

 index                    | 1                                                                                                  
 interface                | wlan1                                                                                              
 state                    | WIFI_WDS                                                                                           
 hw-addr                  | e8:28:c1:da:cb:80                                                                                  
 ip-addr                  | 10.24.80.40                                                                                        
 hostname                 | WEP-2L                                                                                             
 authorized               | false                                                                                              
 captive-portal-vap       | false                                                                                              
 enterprise-vap           | false                                                                                              
 rx-retry-count           | 10                                                                                                 
 tx-fails                 | 0                                                                                                  
 tx-period-retry          | 0                                                                                                  
 tx-retry-count           | 0                                                                                                  
 rssi-1                   | -75                                                                                                
 rssi-2                   | -70                                                                                                
 snr-1                    | 40                                                                                                 
 snr-2                    | 39                                                                                                 
 wds-interface            | wlan1-wds2                                                                                         
 tx-rate                  | VHT NSS2-MCS8 SGI 173.3                                                                            
 rx-rate                  | VHT NSS2-MCS8 NO SGI 156                                                                           
 rx-bw                    | 20M                                                                                                
 rx-bw-all                | 20M                                                                                                
 tx-bw                    | 20M                                                                                                
 uptime                   | 00:07:15                                                                                           
 multicast-groups-count   | 0                                                                                                  
 wireless-mode            | ac                                                                                                 
 eltex-firmware-version   | 1.2.1 build X
 eltex-board-type         | WEP-2L                                                                                             
 perftest-capable         | false                                                                                              
 snr-rssi-capable         | false                                                                                              
 link-capacity            | 90 (not changed)                                                                                   
 link-quality             | 100 (not changed)                                                                                  
 link-quality-common      | 100                                                                                                
 actual-tx-rate           | 0                                                                                                  
 actual-rx-rate           | 5                                                                                                  
 shaped-rx-rate           | 0                                                                                                  
 actual-tx-pps            | 0                                                                                                  
 actual-rx-pps            | 8                                                                                                  
 shaped-rx-pps            | 0                                                                                                  
 name                     | 0                                                                                                  
                                                                                                                               
 Rate                  Transmitted            Received                                                                         
---------------------------------------------------------------------                                                          
 Total Packets:       | 53                   | 2125                 |                                                          
 TX success:          | 100                  |                      |                                                          
 Total Bytes:         | 4300                 | 261666               |                                                          
 Data Packets:        | 48                   | 2120                 |                                                          
 Data Bytes:          | 2496                 | 193382               |                                                          
 Mgmt Packets:        | 5                    | 5                    |                                                          
 Mgmt Bytes:          | 268                  | 444                  |                                                          
---------------------------------------------------------------------                                                          
                                                                                                                               
 Rate                  Transmitted            Received                                                                         
---------------------------------------------------------------------                                                          
 ofdm6                | 7              |  13%|             12 |   0%|                                                          
 ofdm54               | 1              |   1%|              0 |   0%|                                                          
 nss2-mcs0            | 4              |   7%|              6 |   0%|                                                          
 nss2-mcs1            | 4              |   7%|              8 |   0%|                                                          
 nss2-mcs2            | 4              |   7%|              6 |   0%|                                                          
 nss2-mcs3            | 4              |   7%|              6 |   0%|                                                          
 nss2-mcs4            | 4              |   7%|              7 |   0%|                                                          
 nss2-mcs5            | 4              |   7%|              4 |   0%|                                                          
 nss2-mcs6            | 4              |   7%|              7 |   0%|                                                          
 nss2-mcs7            | 9              |  16%|             24 |   1%|                                                          
 nss2-mcs8            | 8              |  15%|           2044 |  96%|                                                          
---------------------------------------------------------------------                                                          
                                                                                                                               
                                                                                                                               
Multicast groups: none  

 index                    | 0                                                                                                  
 interface                | wlan1                                                                                              
 state                    | WIFI_WDS                                                                                           
 hw-addr                  | e8:28:c1:d1:43:15                                                                                  
 ip-addr                  | 10.24.80.35                                                                                        
 hostname                 | WEP-2L                                                                                             
 authorized               | false                                                                                              
 captive-portal-vap       | false                                                                                              
 enterprise-vap           | false                                                                                              
 rx-retry-count           | 10                                                                                                 
 tx-fails                 | 0                                                                                                  
 tx-period-retry          | 0                                                                                                  
 tx-retry-count           | 0                                                                                                  
 rssi-1                   | -25                                                                                                
 rssi-2                   | -20                                                                                                
 snr-1                    | 40                                                                                                 
 snr-2                    | 39                                                                                                 
 wds-interface            | wlan1-wds1                                                                                         
 tx-rate                  | VHT NSS2-MCS8 SGI 173.3                                                                            
 rx-rate                  | VHT NSS2-MCS8 NO SGI 156                                                                           
 rx-bw                    | 20M                                                                                                
 rx-bw-all                | 20M                                                                                                
 tx-bw                    | 20M                                                                                                
 uptime                   | 00:02:44                                                                                           
 multicast-groups-count   | 0                                                                                                  
 wireless-mode            | ac                                                                                                 
 eltex-firmware-version   | 1.2.1 build X
 eltex-board-type         | WEP-2L                                                                                             
 perftest-capable         | false                                                                                              
 snr-rssi-capable         | false                                                                                              
 link-capacity            | 90 (not changed)                                                                                   
 link-quality             | 100 (not changed)                                                                                  
 link-quality-common      | 100                                                                                                
 actual-tx-rate           | 0                                                                                                  
 actual-rx-rate           | 5                                                                                                  
 shaped-rx-rate           | 0                                                                                                  
 actual-tx-pps            | 0                                                                                                  
 actual-rx-pps            | 8                                                                                                  
 shaped-rx-pps            | 0                                                                                                  
 name                     | 0                                                                                                  
                                                                                                                               
 Rate                  Transmitted            Received                                                                         
---------------------------------------------------------------------                                                          
 Total Packets:       | 53                   | 2125                 |                                                          
 TX success:          | 100                  |                      |                                                          
 Total Bytes:         | 4300                 | 261666               |                                                          
 Data Packets:        | 48                   | 2120                 |                                                          
 Data Bytes:          | 2496                 | 193382               |                                                          
 Mgmt Packets:        | 5                    | 5                    |                                                          
 Mgmt Bytes:          | 268                  | 444                  |                                                          
---------------------------------------------------------------------                                                          
                                                                                                                               
 Rate                  Transmitted            Received                                                                         
---------------------------------------------------------------------                                                          
 ofdm6                | 7              |  13%|             12 |   0%|                                                          
 ofdm54               | 1              |   1%|              0 |   0%|                                                          
 nss2-mcs0            | 4              |   7%|              6 |   0%|                                                          
 nss2-mcs1            | 4              |   7%|              8 |   0%|                                                          
 nss2-mcs2            | 4              |   7%|              6 |   0%|                                                          
 nss2-mcs3            | 4              |   7%|              6 |   0%|                                                          
 nss2-mcs4            | 4              |   7%|              7 |   0%|                                                          
 nss2-mcs5            | 4              |   7%|              4 |   0%|                                                          
 nss2-mcs6            | 4              |   7%|              7 |   0%|                                                          
 nss2-mcs7            | 9              |  16%|             24 |   1%|                                                          
 nss2-mcs8            | 8              |  15%|           2044 |  96%|                                                          
---------------------------------------------------------------------                                                          
                                                                                                                               
                                                                                                                               
Multicast groups: none  

 hw-addr                  | 32:5b:60:62:e0:a4
 ip-addr                  | 10.24.80.58
 tx-rate                  | MCS15 NO SGI 270
 rx-rate                  | MCS14 NO SGI 117
 uptime                   | 00:07:57

 hw-addr                  | 32:5b:60:62:e0:a4
 rssi-1                   | -24
 rssi-2                   | -24
 wireless-mode            | n
 interface                | wlan1-va0

 hw-addr                  | bc:2e:f6:cc:85:46
 rssi-1                   | -38
 rssi-2                   | -53
 wireless-mode            | ac
 interface                | wlan1-va2

Device info

   system-time: 09:15:16 28.10.2021                                                                                            
   uptime: 15:45:10                                                                                                            
   software-version: 1.2.1 build X
   secondary-software-version: 1.2.1 build X
   boot-version: 1.2.1 build X
   memory-usage: 67                                                                                                            
   memory-free: 34                                                                                                             
   memory-used: 71                                                                                                             
   memory-total: 105                                                                                                           
   cpu: 0.28                                                                                                                   
   is-default-config: true                                                                                                     
   board-type: WEP-2L                                                                                                          
   hw-platform: WEP-2L                                                                                                         
   factory-wan-mac: E8:28:C1:xx:xx:xx                                                                                          
   factory-lan-mac: E8:28:C1:xx:xx:xx                                                                                          
   factory-serial-number: WP39000059                                                                                           
   hw-revision: 1v1                                                                                                            
   session-password-initialized: false                                                                                         
   ott-mode: false                                                                                                             
   last-reboot-reason: firmware update                                                                                         
   test-changes-mode: false  

Network information

   interface: br0
   protocol: dhcp
   ip-address: 192.168.1.15
   mac: e8:28:c1:xx:xx:xx
   mask: 255.255.255.0
   gateway: 192.168.1.1
   DNS-1: 192.168.1.100
   DNS-2: 
   rx-bytes: 4864149
   rx-packets: 13751
   tx-bytes: 2462399
   tx-packets: 20753

   link: up
   speed: 1000
   duplex: enabled
   rx-bytes: 4872597
   rx-packets: 13844
   tx-bytes: 2477091
   tx-packets: 20923

#        ip                mac              
--------------------------------------------
0        192.168.1.1       02:00:48:xx:xx:xx
1        192.168.1.151     2c:fd:a1:xx:xx:xx

Destination       Gateway           Mask              Flags      Interface 
--------------------------------------------------------------------------
0.0.0.0           192.168.1.1      0.0.0.0            UG         br0       
192.168.1.0       0.0.0.0          255.255.255.0      U          br0  

Wireless interfaces

hwaddr: E8:28:C1:xx:xx:xx
status: on
noise-1: -100
noise-2: -100
utilization: 21
channel: 11
thermal: 30
bandwidth: 20
frequency: 2462

hwaddr: E8:28:C1:xx:xx:xx
status: on
noise-1: -100
noise-2: -100
utilization: 0
channel: 132
thermal: 31
bandwidth: 20
frequency: 5660

Event logging

Jan  23 00:00:07 WEP-2L daemon.info syslogd[925]: started: BusyBox v1.21.1

Jan  23 00:00:09 WEP-2L daemon.info configd[955]: The AP startup configuration was loaded successfully.

Jan  1 03:00:14 WEP-2L daemon.info networkd[987]: Networkd started

Jan  1 03:01:17 WEP-2L daemon.info networkd[987]: DHCP-client: Interface br0 obtained lease on 192.168.1.15.

Jan 23 07:17:14 WEP-2L daemon.info monitord[1055]: event: 'associated' mac: E4:0E:EE:BD:AE:6B ssid: 'WEP-2L_2.4GHz' int0

Environment scan

SSID                             |Mode |Security|MAC               |Channel|RSSI, dBm|Bandwidth, MHz                           
---------------------------------|-----|--------|------------------|-------|---------|--------------                                                           
ESRAP1_of30_smart                |AP   |off     |A8:F9:4B:B0:2C:C7 |6      |-65      |20                                       
litv_hots_2                      |AP   |off     |E0:D9:E3:8A:38:52 |1      |-65      |20                                       
test_001                         |AP   |off     |E0:D9:E3:4B:FB:30 |11     |-67      |20                                       
2G-COVID_TOWER                   |AP   |off     |E0:D9:E3:98:12:72 |11     |-71      |20                                       
Tam2.4G                          |AP   |wpa     |E0:D9:E3:98:1F:7A |1      |-73      |20                                       
litv_hots_1                      |AP   |off     |E0:D9:E3:8A:38:51 |1      |-77      |20                                       
WEP-2L_ZN_Personal               |AP   |wpa     |E0:D9:E3:49:79:06 |44     |-16      |20                                       
WEP-2L_ZN_Open                   |AP   |off     |E0:D9:E3:49:79:07 |44     |-17      |20                                       
Eltex-Guest                      |AP   |off     |CC:9D:A2:C7:D9:21 |36     |-38      |20                                       
Eltex-Local                      |AP   |wpa     |CC:9D:A2:C7:D9:22 |36     |-38      |20                                       
BRAS-Guest                       |AP   |off     |CC:9D:A2:C7:D9:20 |36     |-38      |20                                       
2L_301_nsk                       |AP   |off     |E8:28:C1:DA:C8:16 |56     |-41      |20                                       
chudo_waffly                     |AP   |wpa     |E0:D9:E3:70:94:00 |60     |-44      |20                                       
Eltex VAP                        |AP   |off     |A8:F9:4B:B0:40:70 |48     |-46      |20                                       
VK_enterprise                    |AP   |wpa     |E8:28:C1:DA:C8:99 |56     |-47      |20                                       
VK_portal                        |AP   |off     |E8:28:C1:DA:C8:98 |56     |-49      |20                                       
WOP-2ac                          |AP   |off     |E8:28:C1:00:FC:A1 |36     |-50      |80                                       
Open_VK_switch                   |AP   |off     |E8:28:C1:DA:C8:96 |56     |-50      |20                                       
testSSID10                       |AP   |off     |A8:F9:4B:B0:05:54 |40     |-51      |20                                       

Spectrum Analyzer

The spectrum analyzer provides information on channel utilization in the 2.4 and 5 GHz bands. The result is displayed as a percentage.

 Channel| CCA
       1|  81%
       2|  40%
       3|  14%
       4|  10%
       5|  36%
       6|  60%
       7|  40%
       8|   8%
       9|  14%
      10|  38%
      11|  75%
      12|  37%
      13|  18%
      36|  14%
      40|  12%
      44|  10%
      48|  18%
      52|   3%
      56|   5%
      60|   8%
      64|   6%
     132|   0%
     136|   0%
     140|   0%
     144|   1%
     149|  30%
     153|   1%
     157|   3%
     161|   2%
     165|   1%

The list of changes