gpon olt authentication

The command sets the ONT authentication mode: by password, by serial number, by a combination of serial number and password. The use of a negative form (no) of the command sets the default value.

Syntax     

gpon olt authentication <VALUE>
no gpon olt authentication

Parameters

<VALUE> – ONT authentication mode:

• password – by password;
• serial – by serial number;
• both – by combination of serial number and password.

Default value:

both – ONT authentication by combination of serial number and password

Command mode

CONFIG

Example

ma4000(config)# gpon olt authentication password

gpon olt block-duplicated-mac

This command enables protection against duplicate MAC addresses (MAC spoofing).

The use of the negative form (no) disables ONT blocking when duplicated MAC addresses are detected.

Syntax

[no] gpon olt block-duplicated-mac

Parameters

The command contains no arguments.

Default value:

disable – blocking disabled

Command mode

CONFIG

Example

ma4000(config)# gpon olt block-duplicated-mac

gpon olt broadcast-gem-port

The command sets the GEM port number for broadcast traffic.

The use of a negative form (no) of the command sets the default value.

Syntax     

gpon olt broadcast-gem-port <PORT>
no gpon olt broadcast-gem-port

Parameters

<PORT> – number of GEM port for broadcast traffic, may take values [0..4095].

Default value

4095

Command mode

CONFIG

Example

ma4000(config)#gpon olt broadcast-gem-port 4095

gpon olt dba-reduced-latency

The command enable the mode to lower DBA latency.

The use of a negative form (no) of the command sets the default value.

Syntax

[no] gpon olt dba-reduced-latency enable

Parameters

The command contains no arguments.

Command mode

CONFIG

Example

ma4000(config)# gpon olt dba-reduced-latency enable

gpon olt dhcpra-shaper

This command sets the maximum number of DHCP messages per second (for each ONT)

The use of a negative form (no) of the command sets the default value.

Syntax     

gpon olt dhcpra-shaper <VALUE>
no gpon olt dhcpra-shaper

Parameters

<VALUE> – maximum number of DHCP messages per second for ONT.

Default value:

100

Command mode

CONFIG

Example

ma4000(config)# gpon olt dhcpra-shaper 33

gpon olt encryption

The command enables GPON traffic encryption.

The use of the negative form (no) of the command disables GPON traffic encryption.

Syntax     

[no] gpon olt encryption

Parameters

The command contains no arguments.

Command mode

CONFIG

Example

ma4000(config)# gpon olt encryption

gpon olt encryption key-update

The command is used to set an encryption key change period.

The use of a negative form (no) of the command sets the default parameter value.

Syntax     

gpon olt encryption key-update <TIME>
no gpon olt encryption key-update

Parameters

<TIME> – encryption key update period, may take values [0..65535], in minutes.

Default value:

1 minute

Command mode

CONFIG

Example

ma4000(config)# gpon olt encryption key-update 33333

gpon olt model

The command sets the datapath construction model – the order of forming rules for traffic transfer.

The use of a negative form (no) of the command sets the default parameter value.

Syntax     

gpon olt model  <VALUE>
no gpon olt model

Parameters

<VALUE> – datapath construction model:

1. transmission of Broadcast and unicast packets in one GEM port, VLAN operation (U-VID assignment) is performed on OLT side;
2. transmission of Broadcast traffic in dedicated GEM port, VLAN operation (U-VID assignment) is performed on OLT side;
3. transmission of Broadcast traffic in dedicated GEM port, VLAN operation (U-VID assignment) is performed on ONT side.

Default value

model1

Command mode

CONFIG

Example

ma4000(config)# gpon olt model 1

gpon olt multicast-gem-port

The command sets the GEM port number for multicast traffic.

The use of a negative form (no) of the command sets the default parameter value.

Syntax     

gpon olt multicast-gem-port <PORT>
no gpon olt multicast-gem-port

Parameters

<PORT> – number of GEM port for multicast traffic, may take values [0..4095].

Default value

4094

Command mode

CONFIG

Example

ma4000(config)# gpon olt multicast-gem-port 32

gpon olt ont-block-time

This command sets the time to lock the port when duplicate MAC addresses are detected.

The use of a negative form (no) of the command sets the default value.

Syntax     

gpon olt ont-block-time <TIME>
no gpon olt ont-block-time

Parameters

<TIME> – blocking time, may take values in the range [1..2147483647] minutes.

Default value

5 minutes

Command mode

CONFIG

Example

ma4000(config)#gpon olt ont-block-time 10	

gpon olt ont-sn-format

This command sets the format of displaying the ONT serial number.

The use of a negative form (no) of the command sets the default value.

Syntax     

gpon olt ont-sn-format <VALUE>
no gpon olt ont-sn-format

Parameters

<VALUE> – display format:

• literal – AAAAXXXXXXXX, where A is uppercase letter, and X in HEX format [0-F];
• numerical – XXXXXXXXXXXXXXXX, where X in HEX format [0-F];
• section-numerical – XX-XX-XX-XX-XX-XX-XX-XX, where X in HEX format [0-F].

Default value

literal

Command mode

CONFIG

Example

ma4000(config)#gpon olt ont-sn-format literal

show gpon olt

The command to view the settings of GPON-configuration of PLC8 modules:

• Block duplicated mac – protection against duplicate MAC addresses;
• Ont block time – port blocking time in minutes when detecting duplicate MAC addresses;
• Dhcpra shaper – maximum number of DHCP messages per second for each ONT;
• Datapath – datapath configuration:
• Model – datapath construction model;
• Broadcast gem port – number of GEM port for broadcast traffic;
• Multicast gem port –number of GEM port for multicast traffic;
• Encryption – GPON traffic encryption settings
• Enable – GPON traffec incryption state: enabled, disabled;
• Key update interval – encryption key update period, in minutes;
• ONT authentication mode – ONT authentication mode;
• Auto reconfigure ont – ONT auto reconfiguration state: enabled, disabled;
• Auto reconfigure channel – channel auto reconfiguration state: enabled, disabled;
• Auto reconfigure olt – OLT auto reconfiguration state: enabled, disabled;
• Ont sn format – ONT serial number display format.

Syntax     

show gpon olt

Parameters

Command contains no arguments.

Command mode

ROOT

Example

ma4000(config)# showgponolt
Block duplicated mac:                          disabled
        Ont block time:                                5
        Dhcpra shaper:                                 100
        Datapath:
            Model:                                     model1
            Broadcast gem port:                        4095
            Multicast gem port:                        4094
        Encryption:
            Enable:                                    false
            Key update interval:                       1
        ONT authentication mode:                       both
        Auto reconfigure ont:                          true
        Auto reconfigure channel:                      true
        Auto reconfigure olt:                          true
        Ont sn format:                                 literal