LTP-8X, LTP-4X optical line terminals Application to the user manual Firmware version 3.46.0 |
|
Notes and warnings
Notes contain important information, tips or recommendations on device operation and configuration. |
Warnings are used to inform the user about situations that may cause harm to a software and hardware complex, lead to malfunction or data loss. |
This manual specifies the following:
Safety rules and Installation procedure:
The following scheme is given as an example, figure 1:
Figure 1 — Example of network configuration
Service type | VLAN used |
---|---|
Internet | 2149 |
VoIP | 3149 |
IPTV (multicast) | 30 |
STB | 2349 |
MNG-ONT (acs) | 4094 |
MNG OLT | 4000 |
It is required any PC application with support for Telnet or SSH protocol operation or direct connection via the console port (e.g. HyperTerminal).
General requirements
Any operations with the terminal should comply to the "Safety Regulations for Operation of Consumer's Electrical Installations".
Operations with the terminal should be carried out only by personnel authorised in accordance with the safety requirements. |
Electrical safety requirements
Check the device for visible mechanical damage before installing and turning it on. In case of any damage, stop the installation, fill in a corresponding document and contact your supplier. If the terminal was exposed to low temperatures for a long time before installation, leave it for 2 hours at ambient temperature prior to operation. If the device was exposed to high humidity for a long time, leave it for at least 12 hours in normal conditions prior to turning it on.
The delivery package includes support brackets for rack installation and mounting screws to fix the terminal case on the brackets. To install the support brackets:
Figure 2 — Support brackets mounting
To install the terminal into the rack:
Figure 3 — Device rack installation
The terminal is horizontally ventilated. The side panels have air vents. Do not block the air vents to avoid components overheating and subsequent terminal malfunction.
To avoid overheating and provide necessary ventilation of the terminal, sufficient space should be provided above and below the terminal, not less than 10 cm. |
Depending on power supply requirements, terminals can be supplemented with either an AC power module, 220 V, 50 Hz, or a DC power supply module, 48 V. The installation location for the power module for LTP-X rev.B is shown in figure 4.
The installation location for the power module for LTP-X rev.C/rev.D is shown in figure 5.
Figure 4 — Power module installation for LTP-X rev.B
Figure 5 — Power module installation for LTP-X rev.C/rev.D
To install a power module:
Connect the network data cable to one of the 'GE Port' or 'Combo GE' of LTP-X. The following factory settings are used for SSH/Telnet connection:
login:admin Password: password |
For security reasons, it is recommended to change the factory password when connecting for the first time (see Section Changing the user password). |
If the device does not connect with the factory IP address, connect to it via the COM port using the terminal program and check the network settings (see Connecting via serial port).
A null modem cable is used for connection. The null modem cable pin designation is given in Appendix С. RS-232 null-modem cable pin designation.
To connect via the serial port, the following settings must be set:
For security reasons, it is recommended to change the factory password when connecting for the first time (see Section Changing the user password). |
Check the network settings with the show management command.
Check the network settings LTP-X# show management Network: Hostname: 'LTP-X' Ipaddr: 192.168.1.2 Netmask: 255.255.255.0 Vlan management: 1 Gateway: 0.0.0.0 Vlan prio: 7 Dscp: 63 |
Go to the configuration mode LTP-X# configure terminal Show created users LTP-X(config)# do show users config Set the new password for admin LTP-X(config)# user admin password XXXX Set the new password for root LTP-X(config)# user root password XXXX Apply the configuration LTP-X(config)# do commit Save the configuration LTP-X(config)# do save |
For remote management of LTP-X, you should set network parameters of the device according to the settings of the network that you intend to use. Changing the network parameters of the device is recommended when connecting to the CLI via a serial interface.
Go to the configuration mode LTP-X# configure terminal |
Set the required network settings, e.g. IP=192.168.205.105, Mask=255.255.255.0, Gateway=192.168.205.230, VLAN=4000.
LTP-X(config)# management ip 192.168.205.105 LTP-X(config)# management mask 255.255.255.0 LTP-X(config)# management gateway 192.168.205.230 LTP-X(config)# management vid 4000 LTP-X(config)# exit Check the network settings LTP-X# show management Network: Hostname: 'LTP-X' Ipaddr: 192.168.205.105 Netmask: 255.255.255.0 Vlan management: 4000 Gateway: 192.168.205.230 Vlan prio: 7 Dscp: 63 Additional vlan: <list is empty> The new network settings will be applied after applying/saving the configuration with the commit, save commands without rebooting the device: Apply the configuration LTP-X# commit Save the configuration LTP-X# save If VLAN will be used for control (in this example, VID=4000), you should add it to the SWITCH configuration: Go to the SWITCH mode LTP-X# switch SWITCH configuration mode LTP-X(switch)# configure terminal Add the required VLAN LTP-X(switch)(config)# vlan 4000 Receive the traffic in VLAN from front-port 0 LTP-X(switch)(config-vlan)# tagged front-port 0 LTP-X(switch)(config-vlan)# exit |
Apply the configuration LTP-X(switch)(config)# commit LTP-X(switch)(config)# exit LTP-X(switch)# exit Save the configuration LTP-X# save |
For proper operation of LTP-X, it is recommended to update the firmware. The actual firmware version can be checked in the vendor's technical support section.
Upload the firmware file to the TFTP server (as an example, firmware version 3.40.0-build2358).
Next, download this file to LTP-X using the following command.
Specify firmware file name and TFTP server address LTP-8X# copy tftp://192.168.205.250/ltp-8x-revc-revd-3.40.0-build2358.fw.bin fs://firmware Check free memory...ok Downloading system firmware.. ............................................................ ............................................................ .............................................. System firmware successfully downloaded Updating system firmware.. Current board version: 6 Current firmware version: 3.38.2.16 New firmware version: 3.40.0.2358 Update device mtd7 Erase flash... Done. Write data... Done. Done. Success Update device mtd8 Erase flash... Done. Write data... Done. Done. Success Update device mtd5 Erase flash... Done. Write data... Done. Done. Success Update device mtd6 Erase flash... Done. Write data... Done. Done. Success System firmware successfully updated LTP-8X# |
Reboot the device using the reboot command.
Reboot device LTP-X# reboot Do you really want to reboot the system now? (y/n) y |
After LTP-8X loading, the firmware version can be found by the show version command.
LTP-8X# show version Eltex LTP-8X:rev.C software version 3.40.0 build 2358 on 10.12.2018 15:32 |
SNMP is a protocol designed for monitoring and managing network devices.
Go to the configuration mode LTP-X# configure terminal Enable SNMP LTP-X(config)# ip snmp enable Specify version v2 and EMS server address LTP-X(config)# ip snmp traps 192.168.205.200 type v2 Check SNMP parameters LTP-X(config)# do show ip snmp Snmp: Enabled: true Access control: false Allow ip: <list is empty> Traps [0]: Type: v2 Ipaddr: 192.168.205.200 Version: v2 Community read-only [0]: 'QwYva0dvS3N' Community read-only [1]: 'QwYva0dvS3N' Community read-only [2]: 'QwYva0dvS3N' Community read-write [0]: 'LQtfx9v3m9+qA==' Community read-write [1]: 'LQtfx9v3m9+qA==' Community read-write [2]: 'LQtfx9v3m9+qA==' Trap community: '9qXUEDwUMAg' Location: 'unknown' Contact: 'admin' Alias: <for showing use separate command> EngineID: 0xEF20CAF8234E12401216B17D85 Users: <for showing use separate command> Apply the configuration LTP-X(config)# do commit Save the configuration LTP-X(config)# do save |
Syslog is a protocol designed for sending system event messages and error notifications to remote servers.
Go to the configuration mode LTP-X# configure terminal Specify syslog server address * LTP-X(config)# logging remote 192.168.205.200 Check syslog settings LTP-X(config)# do show logging Log: Remote syslog: 192.168.205.200 Port: 514 Size: 16384 Origin-id: Type: ip Save logs between boots: false Log input commands: false Destinations: System: notice Console: critical Remote shells: critical File: notice Apply the configuration LTP-X(config)# do commit Save the configuration LTP-X(config)# do save * - up to 4 servers can be secified at the same time. |
NTP is a protocol designed for time synchronization between the network device and the server.
Go to the configuration mode LTP-X# configure terminal Enable NTP service LTP-X(config)# ip ntp enable Specify NTP server address LTP-X(config)# ip ntp ip 192.168.205.200 Specify timezone LTP-X(config)# ip ntp timezone 7 |
Check NTP settings LTP-X(config)# do show ip ntp Ntp: Enabled: true Ntpserver: 192.168.205.200 Interval: 3600 Timezone: 7 Daylightsaving: false Apply the configuration LTP-X(config)# do commit Save the configuration LTP-X(config)# do save |
Starting from version 3.26.0, OLT supports the IP Source Guard functionality, which allows you to limit the unauthorized use of IP addresses on the network. The verification is carried out by binding the IP address to the source MAC address for a specific service on a specific ONT.
Go to the configuration mode LTP-X# configure terminal Enable Source Guard service LTP-X(config)# ip source-guard enable Set the mode LTP-X(config)# ip source-guard mode dynamic |
To add static bindings, use the following command:
LTP-X(config)# ip source-guard bind ip <IP> mac <MAC> interface-ont <ONT> service <NUM>
Where:
To reduce the broadcast traffic and avoid responses from illegal DHCP servers, unicast messages can be configured to interact with the specified DHCP Relay Agent. Relay Agent can be individually started for each separate VLAN. The service allows processing only for the packets, which have only one 802.1q tag.
Create an L3 interface by specifying the IP address of the VLAN the service is provided for. If the address of the DHCP server is in the same network as the management interface, skip Step 3. If the DHCP server is in the VLAN, which is specified in cross-connect, the IP address of the interface being created should be in the same network as the DHCP server, and you should skip Step 3.
Add VLAN LTP-X(switch)(config)# vlan 2000 Set IP address for VLAN 2000 LTP-X(switch)(config-vlan)# ip address 10.10.10.1/32 |
Specify DHCP server address.
Specify DHCP server IP address LTP-X(switch)(config-vlan)# ip dhcp relay 192.168.56.1 |
Create an L3 interface by specifying the IP address of the VLAN, which is used for switching in the network where the DHCP server is located.
Add VLAN LTP-X(switch)(config)# vlan 1209 LTP-X(switch)(config-vlan)# ip address 192.168.209.240/24 |
If the address of the DHCP server is located after the router available after the specified L3 interface, configure a static route.
LTP-X(config)# ip route prefix 192.168.56.0 mask 24 gateway 192.168.209.5 LTP-X(switch)(config-vlan)# ip address 192.168.209.240/24 |
Go to the SWITCH mode LTP-X# switch SWITCH configuration mode LTP-X(switch)# configure Add all required VLANs LTP-X(switch)(config)# vlan 2149,2349,30,3149,4094 Transmit tagged to all pon ports* LTP-X(switch)(config-vlan-range)# tagged pon-port 0 – 7 Receive the traffic in VLAN from front-port 0 LTP-X(switch)(config-vlan-range)# tagged front-port 0 Go to the configuration mode LTP-X(switch)(config-vlan-range)# exit Apply the configuration LTP-X(switch)(config)# commit LTP-X(switch)(config)# exit LTP-X(switch)# exit Save the configuration LTP-X# save |
* The command is applicable for:
LTP-8Х rev.B with HW_revision 2vХ.
LTP-8Х rev.С/rev.D with HW_revision 1vХ.
For LTP-4X rev.B/LTP-4X rev.C/rev.D, the tagged pon-port 0 – 3 command is applied.
The hardware version of LTP-X can be found using the following command.
LTP-8X# show system environment System information: CPU load average (1m, 5m, 15m): 0.83 2.35 1.48 Free RAM/Total RAM (Mbytes): 279/495 Temperature (sensor1/sensor2): 35C/48C Reset button: enabled Fan configured speed, %: auto Fan minimum speed, %: 15 Fan speed levels, %: 16 27 39 51 64 76 88 100 Fan state (fan0/fan1): 6300rpm 6450rpm PLD FW version: 14 TYPE: LTP-8X-rev.C HW_revision: 1v1 SN: GP2B000024 MAC: A8:F9:4B:8B:50:00 Power supply information: Module 1: PM150 220/12 1vX Type: Alternate current(AC) Intact: 1 Module 2: PM150 220/12 1vX Type: Alternate current(AC) Intact: 1 |
If you do not save the settings, after restarting, the device will return to the last saved configuration. |
Enable IGMP SNOOPING globally LTP-X(switch)(config)# ip igmp snooping VLAN 30 configuration mode LTP-X(switch)(config)# vlan 30 Enable IGMP SNOOPING in VLAN multicast LTP-X(switch)(config-vlan)# ip igmp snooping enable Enable IGMP proxying LTP-X(switch)(config-vlan)# ip igmp snooping querier enable Enable IGMP-report proxying LTP-X(switch)(config-vlan)# exit LTP-X(switch)(config)# ip igmp proxy report enable Specify IGMP address range for proxying from unicast to multicast VLANs LTP-X(switch)(config)# ip igmp proxy report range 224.0.0.1 239.255.255.255 from 2349 to 30 Apply the configuration LTP-X(switch)(config)# commit LTP-X(switch)(config)# exit LTP-X(switch)# exit Save the configuration LTP-X# save |
Go to the configuration mode LTP-X# configure terminal Select datapath model 2 LTP-X(config)# gpon olt model 2 Create and switch to a Cross-Connect profile for the ONT Internet service LTP-X(config)# profile cross-connect INTERNET LTP-X(config-cross-connect)("INTERNET")# Specify the service VLAN of the Internet service LTP-X(config-cross-connect)("INTERNET")# outer vid 2149 Specify inner VLAN of Internet service on ONT LTP-X(config-cross-connect)("INTERNET")# user vid 10 LTP-X(config-cross-connect)("INTERNET")# exit Create and switch to a Cross-Connect profile for the ONT SIP VoIP service LTP-X(config)# profile cross-connect VOIP Specify the service VLAN of the VoIP service LTP-X(config-cross-connect)("VOIP")# outer vid 3149 Specify inner VLAN of VoIP service on ONT LTP-X(config-cross-connect)("VOIP")# user vid 12 LTP-X(config-cross-connect)("VOIP")# exit Create and switch to a Cross-Connect profile for the multicast service LTP-X(config)# profile cross-connect MC_IPTV Specify the service VLAN of the multicast service LTP-X(config-cross-connect)(" MC_IPTV ")# outer vid 30 Specify inner VLAN of multicast service on ONT LTP-X(config-cross-connect)(" MC_IPTV ")# user vid 30 Specify multicast service type LTP-X(config-cross-connect)(" MC_IPTV ")# type multicast LTP-X(config-cross-connect)(" MC_IPTV ")# exit Create and switch to a Cross-Connect profile for the ONT UC_IPTV service LTP-X(config)# profile cross-connect UC_IPTV Specify the service VLAN of the STB unicast service LTP-X(config-cross-connect)(" UC_IPTV ")# outer vid 2349 Specify inner VLAN of STB unicast service on ONT LTP-X(config-cross-connect)(" UC_IPTV ")# user vid 11 LTP-X(config-cross-connect)(" UC_IPTV ")# exit Create and switch to a Cross-Connect profile for the ONT management service LTP-X(config)# profile cross-connect ACS Specify service VLAN for management service LTP-X(config-cross-connect)("ACS")# outer vid 4094 Specify inner VLAN for management service in ONT LTP-X(config-cross-connect)("ACS")# user vid untagged Specify management service type LTP-X(config-cross-connect)("ACS")# type management LTP-X(config-cross-connect)("ACS")# exit Create and switch to multicast profile LTP-X(config)# profile ports NTP-RG Enable IGMP Proxy on NTP VoIP interface LTP-X(config-ports)("NTP-RG")# veip multicast Configuration of IGMP traffic mapping in 30th VLAN LTP-X(config-ports)("NTP-RG")# veip upstream vid 30 Configuration of multicast mapping in 30th VLAN LTP-X(config-ports)(" NTP-RG ")# veip downstream vid 30 VLAN multicast configuration, in which the range of the following groups comes LTP-X(config-ports)(" NTP-RG ")# igmp multicast dynamic-entry 0 vid 30 Configuration of the range of multicast groups LTP-X(config-ports)(" NTP-RG ")# igmp multicast dynamic-entry 0 group 224.0.0.1 239.255.255.255 Apply the configuration LTP-X(config-ports)(" NTP-RG ")# do commit Save the configuration LTP-X(config-ports)(" NTP-RG ")# do save |
If you do not save the settings, after restarting, the device will return to the last saved configuration. |
Go to the configuration mode LTP-X# configure terminal Add and switch to profile configuration LTP-X(config)# profile pppoe-ia 1 Enable Agent LTP-X(config-pppoe-ia)("1")# enable Set the maximum number of PPPoE sessions for a profile LTP-X(config-pppoe-ia)("1")# sessions-limit 8094 Set the maximum number of PPPoE sessions for a single ONT LTP-X(config-pppoe-ia)("1")# sessions-limit per-user 4 Configure circuit_id format LTP-X(config-pppoe-ia)("1")# format circuit-id %HOSTNAME%%ONTID% Configure remote_id format LTP-X(config-pppoe-ia)("1")# format remote-id %HOSTNAME%%ONTID% Apply the configuration LTP-X(config-pppoe-ia)("1")# do commit Save the configuration LTP-X(config-pppoe-ia)("1")# do save Assign pppoe-ia 1 profile on OLT LTP-X(config-pppoe-ia)("1")# exit LTP-X(config)# gpon olt profile pppoe-ia 1 Apply the configuration LTP-X(config)# do commit Save the configuration LTP-X(config # do save |
If Auto reconfigure GPON port (Auto reconfigure GPON-port: true) is not set in OLT configuration, then OLT chips must be reconfigured to apply pppoe-ia profile settings. |
Reconfiguration is performed by the following command.
LTP-X# reconfigure olt all |
For LTP-4X:
LTP-X# reconfigure olt |
Go to the configuration mode LTP-X# configure terminal Add and switch to the DHCP profile configuration menu LTP-X(config)# profile dhcp-ra 1 Enable Agent LTP-X(config-dhcp-ra)("1")# enable Send HOSTNAME LTP-X and id ONT in information about which port the request for DHCP relay came from LTP-X(config-dhcp-ra)("1")# overwrite-option82 circuit-id %HOSTNAME%%ONTID% Transmit the HOSTNAME LTP-X and id ONT in the identifier of the DHCP relay itself LTP-X(config-dhcp-ra)("1")# overwrite-option82 remote-id %HOSTNAME%%ONTID% Apply the configuration LTP-X(config-dhcp-ra)("1")# do commit Save the configuration LTP-X(config-dhcp-ra)("1")# do save Assign the required configuration profile globally LTP-X(config)# gpon olt profile dhcp-ra 1 Assign profile 1 on VLAN 3149 LTP-X(config)# gpon olt profile dhcp-ra 1 vid 3149 Apply the configuration LTP-X(config)# do commit Save the configuration LTP-X(config)# do save View OLT configuration LTP-X# show gpon olt configuration Block duplicated mac: enabled Disable rogue ONT: disabled Ont block time: 5 Dhcpra shaper: 100 Profile pppoe-ia: 1 OLT Profile PPPoE Intermediate Agent 1 Profile dhcp-ra: 1 OLT Profile DHCP Relay Agent 1 Profile dhcpv6-ra: dhcpv6-ra-00 OLT Profile DHCP Relay Agent 0 Profile dhcp-ra per VLAN 3149 [0]: Profile: 1 OLT Profile DHCP Relay Agent 1 Profile dhcpv6-ra per VLAN: <list is empty> Datapath: Model: model2 Broadcast gem port: 4095 Multicast gem port: 4094 Encryption: Enable: false Key update interval: 1 Unactivated timeout: 60 ONT authentication mode: both Auto reconfigure ONT: true Auto reconfigure GPON-port: true Auto reconfigure OLT: true PLOAM password in alarm: false Auto-activation ONT: false Default template: unassigned |
With this configuration, for all VLANs except 3149, the DHCP Relay Agent profile 0 will be used.
To apply the DHCP-RA profile settings, it is required to reconfigure the OLT chips, if in the OLT configuration it is not set the "Auto reconfigure GPON-port: true" parameter.
Reconfiguration is performed by the following command.
LTP-X# reconfigure olt all |
For LTP-4X:
LTP-X# reconfigure olt |
It is necessary to add ONT 454C54580800F6B1 to the configuration, to tree 0 ONT ID 1 and assign all the required profiles to it to provide services.
View connected but not added ONT LTP-X# show interface ont 0-7 unactivated ----------------------------------- GPON-port 0 ONT unactivated list ----------------------------------- ## Serial ONT ID GPON-port Status RSSI[dBm] Version EquipmentID Description 1 454C54580800F6B1 n/a 0 UNACTIVATED n/a n/a n/a n/a Go to the configuration mode LTP-X# configure terminal Go to tree 0 ONT ID 1 LTP-X(config)# interface ont 0/1 Assign the required ONT to this position LTP-X(config)(if-ont-0/1)# serial 454C54580800F6B1 Assign ports NTP-RG profile LTP-X(config)(if-ont-0/1)# profile ports NTP-RG Assign cross-connect INTERNET profile LTP-X(config)(if-ont-0/1)# service 0 profile cross-connect INTERNET Assign cross-connect VOIP profile LTP-X(config)(if-ont-0/1)# service 1 profile cross-connect VOIP Assign cross-connect MC_IPTV profile LTP-X(config)(if-ont-0/1)# service 2 profile cross-connect MC_IPTV Assign cross-connect UC_IPTV profile LTP-X(config)(if-ont-0/1)# service 3 profile cross-connect UC_IPTV Assign cross-connect ACS profile LTP-X(config)(if-ont-0/1)# service 4 profile cross-connect ACS Assign default dba profile 'dba 0' to all services used: LTP-X(config)(if-ont-0/1)# service 0 profile dba dba-00 LTP-X(config)(if-ont-0/1)# service 1 profile dba dba-00 LTP-X(config)(if-ont-0/1)# service 2 profile dba dba-00 LTP-X(config)(if-ont-0/1)# service 3 profile dba dba-00 LTP-X(config)(if-ont-0/1)# service 4 profile dba dba-00 Apply the configuration LTP-X(config)(if-ont-0/1)# do commit Save the configuration LTP-X(config)(if-ont-0/1)# do save |
After executing the commands in section 10 of this manual, it is recommended to reset the subscriber terminal to factory configuration.
LTP-X# send omci restore interface ont 0/1 |
After reloading the device, it is necessary to check all services.
View a list of connected ONTs added to the configuration LTP-X# show interface ont 0-7 online ----------------------------------- GPON-port 0 ONT online list ----------------------------------- ## Serial ONT ID GPON-port Status RSSI[dBm] Version EquipmentID Description 1 454C54580800F6B1 1 0 OK -25.38 3.22.0.1493 NTU-RG Total ONT count: 1 |
To simplify the configuration of the same type of ONT, you can use a pre-prepared configuration template 'Template', which will subsequently be assigned to the ONT.
Go to the configuration mode LTP-X# configure terminal Create and switch to TP template LTP-X(config)# template TP Assign ports profile for this template LTP-X(ont-template)("TP")# profile ports NTP-RG Assign cross-connect INTERNET profile on service 0 of TP template LTP-X(ont-template)("TP")# service 0 profile cross-connect INTERNET Assign cross-connect VOIP profile on service 1 of TP template LTP-X(ont-template)("TP")# service 1 profile cross-connect VOIP Assign cross-connect MC_IPTV profile on service 2 of TP template LTP-X(ont-template)("TP")# service 2 profile cross-connect MC_IPTV Assign cross-connect STB profile on service 3 of TP template LTP-X(ont-template)("TP")# service 3 profile cross-connect UC_IPTV Assign cross-connect ACS profile on service 4 of TP template LTP-X(ont-template)("TP")# service 4 profile cross-connect ACS Assign default dba profile 'dba-00' to all services used: LTP-X(ont-template)("TP")# service 0 profile dba dba-00 LTP-X(ont-template)("TP")# service 1 profile dba dba-00 LTP-X(ont-template)("TP")# service 2 profile dba dba-00 LTP-X(ont-template)("TP")# service 3 profile dba dba-00 LTP-X(ont-template)("TP")# service 4 profile dba dba-00 Apply the configuration LTP-X(ont-template)("TP")# do commit Save the configuration LTP-X(ont-template)("TP")# do save Add ONT 454C54580800F6B2: Go to the configuration mode LTP-X# configure terminal Go to tree 0 ONT ID 10 LTP-X(config)# interface ont 0/10 Assign the required ONT to this position LTP-X(config)(if-ont-0/10)# serial 454C54580800F6B2 Assign the TP template to this position LTP-X(config)(if-ont-0/10)# template TP Apply the configuration LTP-X(config)(if-ont-0/10)# do commit |
Save the configuration LTP-X(config)(if-ont-0/10)# do save |
The configuration of the ONT 454C54580800F6B2 will be similar to the configuration of the ONT 454C54580800F6B1 from Section 11, but to add ONT it is enough to execute only 2 commands. When viewing the ONT configuration by the [T] markers, it is easy to distinguish the template configuration parameters from the usual ones.
LTP-8X(config)(if-ont-0/10)# do show interface ont 0/10 configuration ----------------------------------- [ONT0/10] configuration ----------------------------------- Description: '' Enabled: true Serial: ELTX0800F6B1 Password: '0000000000' [T] Fec up: false [T] Downstream broadcast: true [T] Ber interval: none [T] Ber update period: 60 [T] Rf port state: disabled [T] Omci error tolerant: false Service [0]: [T] Profile cross connect: INTERNET ONT Profile Cross Connect 1 [T] Profile dba: dba-00 ONT Profile DBA 0 Custom cross connect: disabled Service [1]: [T] Profile cross connect: VOIP ONT Profile Cross Connect 2 [T] Profile dba: dba-00 ONT Profile DBA 0 Custom cross connect: disabled Service [2]: [T] Profile cross connect: MC_IPTV ONT Profile Cross Connect 3 [T] Profile dba: dba-00 ONT Profile DBA 0 Custom cross connect: disabled Service [3]: [T] Profile cross connect: UC_IPTV ONT Profile Cross Connect 4 [T] Profile dba: dba-00 ONT Profile DBA 0 Custom cross connect: disabled Service [4]: [T] Profile cross connect: ACS ONT Profile Cross Connect 5 [T] Profile dba: dba-00 ONT Profile DBA 0 Custom cross connect: disabled Service [5]: [T] Profile cross connect: unassigned [T] Profile dba: dba-00 ONT Profile DBA 0 Custom cross connect: disabled [T] Profile shaping: shaping-00 ONT Profile Shaping 0 [T] Profile ports: NTP-RG ONT Profile Ports 1 [T] Profile management: unassigned [T] Profile scripting: unassigned Custom model: none Template: TP ONT Template 1 LTP-8X(config)(if-ont-0/10)# |
LTP-4X/8X rev.B and LTP-4X/8X rev.C/rev.D equipment contains in its software a built-in ACS server that allows automatic configuration of ONTs belonging to this OLT.
Enable internal ACS server LTP-X(config)# ip acs server enable Specify the number of VLAN in which the ACS server will operate LTP-X(config)# ip acs server vid 4094 Enable the DHCP server to issue an IP to the ONT LTP-X(config)# ip dhcp server enable Enable adding option 43 to DHCP packets LTP-X(config)# ip dhcp server option-43 Specify a range of addresses to be issued to customers LTP-X(config)# ip dhcp server range "192.168.200.2" "192.168.201.254" Apply the configuration LTP-X(config)#do commit Save the configuration LTP-X(config)#do save Go to the SWITCH mode LTP-X# switch SWITCH configuration mode LTP-X(switch)# configure Set the VLAN ID to connect to ACS LTP-X(switch)(config)# vlan 4094 Transmit tagged to all pon ports* LTP-X(switch)(config-vlan)# tagged pon-port 0 – 7 Apply the configuration LTP-X(switch)(config-vlan)# exit LTP-X(switch)(config)# commit LTP-X(switch)(config)# exit LTP-X(switch)# exit Save the configuration LTP-X# save Go to the configuration mode LTP-X# configure terminal Create and switch to a Cross-Connect profile for the ONT management service LTP-X(config)# profile cross-connect ACS |
Specify service VLAN for management service LTP-X(config-cross-connect)("ACS")# outer vid 4094 LTP-X(config-cross-connect)("ACS")# type management Apply the configuration LTP-X(config-cross-connect)("ACS")# do commit Save the configuration LTP-X(config-cross-connect)("ACS")# do save |
* The command is applicable for:
LTP-8Х rev.B with HW_revision 2vХ.
LTP-8Х rev.С/rev.D with HW_revision 1vХ.
For LTP-4X rev.B/LTP-4X rev.C/rev.D, the tagged pon-port 0 – 3 command is applied.
For operation of ONT with built-in ACS, it is necessary to assign the created CC and Management profiles to this ONT in the same way as described in Section Adding and configuring ONT.
LTP-X> acs Switch to the ONT profile configuration mode (acs)# profile Add profile for ONT TEST (acs-profiles)# add profile TEST Switch to the TEST profile configuration mode (acs-profiles)# profile TEST (acs-profile-name='TEST' Paste the profile from APPENDIX A. (acs-profile-name='TEST')commit (acs-profile-name='TEST') |
For the convenience of working with ACS profiles for ONT, you can download the required profile via FTP/TFTP protocol.
Example of profile downloading
LTP-8x# copy tftp://10.0.0.1/acs-config fs://acs-config |
The downloaded configuration should be in the form of executable commands on the OLT to configure the required profile. The specified commands will be transparently and automatically transmitted to the CLI without completely deleting the configuration of the current profiles. |
File example
profile add profile test1 profile test1 set property InternetGatewayDevice.LANDevice.1.WLANConfiguration.1.PreSharedKey.1.X_ELTEX_RU_UserDefinedPSK 1 nocheck set property InternetGatewayDevice.LANDevice.1.WLANConfiguration.1.RadioEnabled 1 nocheck |
(acs)# Switch to the subscriber configuration mode (acs)# user Add subscriber IVANOV (acs-user)# add user IVANOV Switch to the subscriber IVANOV configuration mode (acs-user)# user IVANOV Set the ONT serial number for subscriber IVANOV (acs-user-subscriber='IVANOV')# set pon_serial 454C54580800F6B1 Set the ACS profile for subscriber IVANOV (acs-user-subscriber='IVANOV')# set profile TEST Set the login for PPPoE session (acs-user-subscriber='IVANOV')# set ppp_login test Set the password for PPPoE session (acs-user-subscriber='IVANOV')# set ppp_password TEST Set SIP PROXY address (acs-user-subscriber='IVANOV')# set sip_proxy 212.122.111.55 Enable phone port 1 (acs-user-subscriber='IVANOV')# set voice1_enable enabled Set the phone number for port 1 (acs-user-subscriber='IVANOV')# set voice1_number 34234234 Set the password for port 1 phone number (acs-user-subscriber='IVANOV')# set voice1_password test |
Ensure that the correct date and time are set on LTP-X. |
Switch to the ACS configuration mode LTP-X> acs Switch to ONT firmware parameters configuration mode (acs)firmware Specify TFTP server address and firmware file name (acs-firmware)copy 192.168.16.26 ntp-rg-3.22.1.14.fw.bin View list of uploaded files (acs-firmware)show files View list of update profiles (acs-firmware)show list Add update profile (acs-firmware)add firmware 1 Switch to profile edit (acs-firmware)firmware 1 View profile configuration (acs-firmware_config-fw id='1')show config Set firmware file for this profile (acs-firmware_config-fw id='1')set file ntp-rg-3.22.1.14.fw.bin Add a configuration profile (corresponding to those ONTs that require firmware updates). The list of profiles is available in the section (acs-profile) by the command 'show list' (acs-firmware_config-fw id='1')add profile TEST |
The next time the ONT contacts ACS, the firmware will update and the ONT will automatically restart.
If you have any questions, contact the ELTEX technical support service.
set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.DHCPServerEnable" "1" nocheck set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.DomainName" "HomeLAN" nocheck set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPInterface.1.Enable" "1" nocheck set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPInterface.1.IPInterfaceAddressingType" "Static" nocheck set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPInterface.1.IPInterfaceIPAddress" "192.168.1.1" nocheck set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPInterface.1.IPInterfaceSubnetMask" "255.255.255.0" nocheck set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPRouters" "192.168.1.1" nocheck set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.MaxAddress" "192.168.1.254" nocheck set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.MinAddress" "192.168.1.2" nocheck set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.SubnetMask" "255.255.255.0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.1.BridgeEnable" "TRUE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.1.BridgeName" "brHSI" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.1.BridgeStandard" "802.1Q" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.1.VLANID" "10" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.2.BridgeEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.2.BridgeName" "brVoIP" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.2.BridgeStandard" "802.1Q" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.2.VLANID" "12" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.3.BridgeEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.3.BridgeName" "brIPTV" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.3.BridgeStandard" "802.1Q" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.3.VLANID" "11" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.4.BridgeEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.4.BridgeName" "MC" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.4.BridgeStandard" "802.1Q" nocheck set property "InternetGatewayDevice.Layer2Bridging.Bridge.4.VLANID" "30" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.1.AdmitOnlyVLANTagged" "FALSE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.1.FilterBridgeReference" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.1.FilterEnable" "TRUE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.1.FilterInterface" "9" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.1.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.10.AdmitOnlyVLANTagged" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.10.FilterBridgeReference" "3" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.10.FilterEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.10.FilterInterface" "3" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.10.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.11.AdmitOnlyVLANTagged" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.11.FilterBridgeReference" "3" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.11.FilterEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.11.FilterInterface" "4" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.11.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.12.AdmitOnlyVLANTagged" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.12.FilterBridgeReference" "4" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.12.FilterEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.12.FilterInterface" "9" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.12.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.13.AdmitOnlyVLANTagged" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.13.FilterBridgeReference" "4" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.13.FilterEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.13.FilterInterface" "13" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.13.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.2.AdmitOnlyVLANTagged" "FALSE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.2.FilterBridgeReference" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.2.FilterEnable" "TRUE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.2.FilterInterface" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.2.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.3.AdmitOnlyVLANTagged" "FALSE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.3.FilterBridgeReference" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.3.FilterEnable" "TRUE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.3.FilterInterface" "2" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.3.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.4.AdmitOnlyVLANTagged" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.4.FilterBridgeReference" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.4.FilterEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.4.FilterInterface" "5" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.4.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.5.AdmitOnlyVLANTagged" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.5.FilterBridgeReference" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.5.FilterEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.5.FilterInterface" "11" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.5.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.6.AdmitOnlyVLANTagged" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.6.FilterBridgeReference" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.6.FilterEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.6.FilterInterface" "10" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.6.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.7.AdmitOnlyVLANTagged" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.7.FilterBridgeReference" "2" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.7.FilterEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.7.FilterInterface" "9" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.7.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.8.AdmitOnlyVLANTagged" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.8.FilterBridgeReference" "2" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.8.FilterEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.8.FilterInterface" "12" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.8.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.9.AdmitOnlyVLANTagged" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.9.FilterBridgeReference" "3" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.9.FilterEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.9.FilterInterface" "9" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.9.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.1.EthernetPriorityMark" "3" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.1.MarkingBridgeReference" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.1.MarkingEnable" "TRUE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.1.MarkingInterface" "9" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.1.VLANIDMark" "10" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.1.VLANIDMarkOverride" "TRUE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.1.VLANIDUntag" "FALSE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.2.EthernetPriorityMark" "3" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.2.MarkingBridgeReference" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.2.MarkingEnable" "TRUE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.2.MarkingInterface" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.2.VLANIDMark" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.2.VLANIDMarkOverride" "FALSE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.2.VLANIDUntag" "TRUE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.3.EthernetPriorityMark" "3" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.3.MarkingBridgeReference" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.3.MarkingEnable" "TRUE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.3.MarkingInterface" "2" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.3.VLANIDMark" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.3.VLANIDMarkOverride" "FALSE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.3.VLANIDUntag" "TRUE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.4.EthernetPriorityMark" "3" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.4.MarkingBridgeReference" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.4.MarkingEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.4.MarkingInterface" "5" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.4.VLANIDMark" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.4.VLANIDMarkOverride" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.4.VLANIDUntag" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.5.EthernetPriorityMark" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.5.MarkingBridgeReference" "2" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.5.MarkingEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.5.MarkingInterface" "9" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.5.VLANIDMark" "12" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.5.VLANIDMarkOverride" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.5.VLANIDUntag" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.6.EthernetPriorityMark" "2" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.6.MarkingBridgeReference" "3" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.6.MarkingEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.6.MarkingInterface" "9" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.6.VLANIDMark" "11" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.6.VLANIDMarkOverride" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.6.VLANIDUntag" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.7.EthernetPriorityMark" "2" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.7.MarkingBridgeReference" "3" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.7.MarkingEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.7.MarkingInterface" "3" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.7.VLANIDMark" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.7.VLANIDMarkOverride" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.7.VLANIDUntag" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.8.EthernetPriorityMark" "2" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.8.MarkingBridgeReference" "3" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.8.MarkingEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.8.MarkingInterface" "4" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.8.VLANIDMark" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.8.VLANIDMarkOverride" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.8.VLANIDUntag" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.9.EthernetPriorityMark" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.9.MarkingBridgeReference" "4" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.9.MarkingEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.9.MarkingInterface" "9" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.9.VLANIDMark" "30" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.9.VLANIDMarkOverride" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.9.VLANIDUntag" "0" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.DigitMap" "x.T" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.DigitMapEnable" "1" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1.PhyReferenceList" "1" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.2.PhyReferenceList" "2" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.SIP.OutboundProxyPort" "5060" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.SIP.RegisterExpires" "610" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.SIP.RegistrarServerPort" "5060" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.SIP.RegistrationPeriod" "600" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.SIP.UserAgentPort" "5060" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.X_WANReferenceList" "12" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.1.AddressingType" "DHCP" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.1.ConnectionType" "IP_Routed" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.1.DHCPClient.SentDHCPOption.1.Enable" "1" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.1.DHCPClient.SentDHCPOption.1.Tag" "60" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.1.DHCPClient.SentDHCPOption.1.Value" "Vk9JUF9OVFAtUkc=" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.1.Enable" "1" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.1.Name" "VoIP_IPoE" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.2.AddressingType" "Static" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.2.ConnectionType" "IP_Routed" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.2.DefaultGateway" "10.0.0.1" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.2.Enable" "1" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.2.ExternalIPAddress" "10.10.10.10" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.2.Name" "MC_IPoE" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.2.SubnetMask" "255.0.0.0" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.2.X_BROADCOM_COM_IGMPEnabled" "1" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.1.ConnectionTrigger" "AlwaysOn" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.1.ConnectionType" "IP_Routed" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.1.Enable" "1" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.1.IdleDisconnectTime" "0" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.1.Name" "HSI_PPP" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.1.NATEnabled" "1" nocheck |
set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.1.Username" "szt" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.1.Password" "szt" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1.CallingFeatures.CallerIDName" "111" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1.DirectoryNumber" "111" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1.Enable" "Enabled" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1.SIP.AuthPassword" "111" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1.SIP.AuthUserName" "111" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.2.CallingFeatures.CallerIDName" "222" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.2.DirectoryNumber" "222" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.2.Enable" "Enabled" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.2.SIP.AuthPassword" "222" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.2.SIP.AuthUserName" "222" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.SIP.OutboundProxy" "test.ru" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.SIP.RegistrarServer" "test.ru" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.SIP.UserAgentDomain" "test.ru" nocheck |
LTP-8X, LTP-4/8X rev.B
DB-9 socket DB-9 socket
LTP-4/8X rev.C
Objective
Configure the terminal in bridge mode, data transmission to the ONT side will be carried out in VLAN 2149.
Solution
A distinctive feature of ONT NTU-1 is its operation only in bridge mode; full configuration is performed by OLT via OMCI protocol without using an ACS server. Add the required VLAN to the LTP switch configuration.
Go to the SWITCH mode LTP-X# switch SWITCH configuration mode LTP-X(switch)# configure Add the required VLAN LTP-X(switch)(config)# vlan 2149 Receive the traffic in VLAN from frontport 0 LTP-X(switch)(config-vlan)# tagged front-port 0 Transmit tagged to all pon ports* LTP-X(switch)(config-vlan)# tagged pon-port 0 – 7 LTP-X(switch)(config-vlan)# exit Apply the configuration LTP-X(switch)(config)# commit LTP-X(switch)(config)# exit LTP-X(switch)# exit |
* The command is applicable for:
LTP-8Х rev.B with HW_revision 2vХ.
LTP-8Х rev.С with HW_revision 1vХ.
For LTP-4X rev.B, the tagged pon-port 0 – 3 command is applied.
Cross-connect and Ports profile configuration
Go to the configuration mode LTP-X# configure terminal Create and switch to a Cross-Connect profile for the NTU-1 LTP-X(config)# profile cross-connect NTU1 Set bridge operation mode LTP-X(config-cross-connect)("NTU1")# bridge Assign the given Cross-connect to bridge group 20 LTP-X(config-cross-connect)("NTU1")# bridge group 20 |
Specify service VLAN for the given service LTP-X(config-cross-connect)("NTU1")# outer vid 2149 LTP-X(config-cross-connect)("NTU1")# exit Create and switch to profile for the NTU-1 LTP-X(config)# profile ports NTU1 Add port 0 to bridge group 20 LTP-X(config-ports)("NTU1")# port 0 bridge group 20 Apply the configuration LTP-X(config-ports)("NTU1")# do commit Save the configuration LTP-X(config-ports)("NTU1")# do save |
Adding and configuring ONT NTU-1.
Go to the configuration mode LTP-X# configure terminal Go to tree 0 ONT ID 3 LTP-X(config)# interface ont 0/3 Assign the required ONT to this position LTP-X(config)(if-ont-0/3)# serial 454C545862000078 Assign ports NTU-1 profile LTP-X(config)(if-ont-0/3)# profile ports NTU1 Assign cross-connect NTU-1 profile LTP-X(config)(if-ont-0/3)# service 0 profile cross-connect NTU1 Assign default DBA profile LTP-X(config)(if-ont-0/3)# service 0 profile dba dba-00 Apply the configuration LTP-X(config)(if-ont-0/3)# do commit Save the configuration LTP-X(config)(if-ont-0/3)# do save |
Configuration example for transmitting multiple VLANs in TRUNK mode via ONT NTU-1
In the current firmware version, it is possible to transmit up to 8 VLANs in trunk mode via ONT NTU-1.
In the example, transmission of VLANs 100 and 200 will be considered.
Add the required VLAN to the LTP switch configuration.
Go to the SWITCH mode LTP-X# switch SWITCH configuration mode LTP-X(switch)# configure |
Add the required VLAN LTP-X(switch)(config)# vlan 100,200 Receive the traffic in VLAN from frontport 0 LTP-X(switch)(config-vlan)# tagged front-port 0 Transmit tagged to all pon ports* LTP-X(switch)(config-vlan)# tagged pon-port 0 – 7 Apply the configuration LTP-X(switch)(config-vlan)# exit LTP-X(switch)(config)# commit LTP-X(switch)(config)# exit LTP-X(switch)# exit |
* The command is applicable for:
LTP-8Х rev.B with version HW_revision 2vХ.
LTP-8Х rev.С with HW_revision 1vХ.
For LTP-4X rev.B, the tagged pon-port 0 – 3 command is applied.
Cross-connect and Ports profile configuration
Go to the configuration mode LTP-X# configure terminal Create and switch to a Cross-Connect profile for the NTU-1 LTP-X(config)# profile cross-connect NTU100 Set bridge operation mode LTP-X(config-cross-connect)("NTU100")# bridge Assign the given Cross-connect to bridge group 20 LTP-X(config-cross-connect)("NTU100")# bridge group 20 Specify service VLAN for the given service LTP-X(config-cross-connect)("NTU100")# outer vid 100 Specify user VLAN for the given service LTP-X(config-cross-connect)("NTU100")# user vid 100 LTP-X(config-cross-connect)("NTU100")# exit Create and switch to a Cross-Connect profile for the NTU-1 LTP-X(config)# profile cross-connect NTU200 Assign the given Cross-connect to bridge group 20 LTP-X(config-cross-connect)("NTU200")# bridge group 20 Specify service VLAN for the given service LTP-X(config-cross-connect)("NTU200")# outer vid 200 Specify user VLAN for the given service LTP-X(config-cross-connect)("NTU200")# user vid 200 LTP-X(config-cross-connect)("NTU200")# exit |
Create and switch to profile for the NTU-1 LTP-X(config)# profile ports NTU1 Add port 0 to bridge group 20 LTP-X(config-ports)("NTU1")# port 0 bridge group 20 Apply the configuration LTP-X(config-ports)("NTU1")# do commit Save the configuration LTP-X(config-ports)("NTU1")# do save |
Adding and configuring ONT NTU-1.
Go to the configuration mode LTP-X# configure terminal Go to tree 0 ONT ID 3 LTP-X(config)# interface ont 0/3 Assign the required ONT to this position LTP-X(config)(if-ont-0/3)# serial 454C545862000078 Assign ports NTU1 profile LTP-X(config)(if-ont-0/3)# profile ports NTU1 Assign cross-connect NTU-1 profile LTP-X(config)(if-ont-0/3)# service 0 profile cross-connect NTU100 Assign default DBA profile LTP-X(config)(if-ont-0/3)# service 0 profile dba dba-00 Assign cross-connect NTU-1 profile LTP-X(config)(if-ont-0/3)# service 1 profile cross-connect NTU200 Assign default DBA profile LTP-X(config)(if-ont-0/3)# service 1 profile dba dba-00 Apply the configuration LTP-X(config)(if-ont-0/3)# do commit |
Objective
Configure the terminal in bridge mode, data transmission to the ONT side will be carried out in VLAN 2149.
Solution
A distinctive feature of ONT SFP-ONU is its operation only in bridge mode; full configuration is performed by OLT using OMCI protocol without using an ACS server.
Add the required VLAN to the LTP switch configuration.
Go to the SWITCH mode LTP-X# switch SWITCH configuration mode LTP-X(switch)# configure Add the required VLAN LTP-X(switch)(config)# vlan 2149 Receive the traffic in VLAN from frontport 0 LTP-X(switch)(config-vlan)# tagged front-port 0 Transmit tagged to all pon ports* LTP-X(switch)(config-vlan)# tagged pon-port 0 – 7 LTP-X(switch)(config-vlan)# exit Apply the configuration LTP-X(switch)(config)# commit LTP-X(switch)(config)# exit LTP-X(switch)# exit |
* The command is applicable for:
LTP-8Х rev.B with version HW_revision 2vХ.
LTP-8Х rev.С with HW_revision 1vХ.
For LTP-4X rev.B, the tagged pon-port 0 – 3 command is applied.
Cross-connect and Ports profile configuration.
Go to the configuration mode LTP-X# configure terminal Create and switch to a Cross-Connect profile for the NTU-1 LTP-X(config)# profile cross-connect SFP Set bridge operation mode LTP-X(config-cross-connect)("NTU1")# bridge Assign the given Cross-connect to bridge group 20 LTP-X(config-cross-connect)("NTU1")# bridge group 20 |
Specify service VLAN for the given service LTP-X(config-cross-connect)("NTU1")# outer vid 2149 LTP-X(config-cross-connect)("NTU1")# exit Create and switch to profile for the SFP-ONU LTP-X(config)# profile ports SFPONU Add port 0 to bridge group 20 LTP-X(config-ports)("NTU1")# port 0 bridge group 20 Apply the configuration LTP-X(config-ports)("NTU1")# do commit Save the configuration LTP-X(config-ports)("NTU1")# do save |
Adding and configuring ONT SFP-ONU.
Go to the configuration mode LTP-X# configure terminal Go to tree 0 ONT ID 3 LTP-X(config)# interface ont 0/3 Assign the required ONT to this position LTP-X(config)(if-ont-0/3)# serial 454C545862000078 Assign ports SFPONU profile LTP-X(config)(if-ont-0/3)# profile ports SFPONU Assign cross-connect SFP-ONU profile LTP-X(config)(if-ont-0/3)# service 0 profile cross-connect SFP Assign default DBA profile LTP-X(config)(if-ont-0/3)# service 0 profile dba dba-00 Apply the configuration LTP-X(config)(if-ont-0/3)# do commit Save the configuration LTP-X(config)(if-ont-0/3)# do save |
Configuration example for transmitting multiple VLANs in TRUNK mode via ONT SFP-ONU
In the current firmware version, it is possible to transmit up to 8 VLANs in trunk mode via ONT SFP-ONU.
In the example, transmission of VLANs 100 and 200 will be considered.
Add the required VLAN to the LTP switch configuration.
Go to the SWITCH mode LTP-X# switch SWITCH configuration mode LTP-X(switch)# configure |
Add the required VLAN LTP-X(switch)(config)# vlan 100,200 Receive the traffic in VLAN from frontport 0 LTP-X(switch)(config-vlan)# tagged front-port 0 Transmit tagged to all pon ports LTP-X(switch)(config-vlan)# tagged pon-port 0 – 7 Apply the configuration LTP-X(switch)(config-vlan)# exit LTP-X(switch)(config)# commit LTP-X(switch)(config)# exit LTP-X(switch)# exit |
Cross-connect and Ports profile configuration.
Go to the configuration mode LTP-X# configure terminal Create and switch to a Cross-Connect profile for the SFP-ONU LTP-X(config)# profile cross-connect SFP100 Set bridge operation mode LTP-X(config-cross-connect)("SFP100")# bridge Assign the given Cross-connect to bridge group 20 LTP-X(config-cross-connect)("SFP100")# bridge group 20 Specify service VLAN for the given service LTP-X(config-cross-connect)("SFP100")# outer vid 100 Specify user VLAN for the given service LTP-X(config-cross-connect)("SFP100")# user vid 100 LTP-X(config-cross-connect)("SFP100")# exit Create and switch to a Cross-Connect profile for the SFP-ONU LTP-X(config)# profile cross-connect SFP200 Assign the given Cross-connect to bridge group 20 LTP-X(config-cross-connect)("SFP200")# bridge group 20 Specify service VLAN for the given service LTP-X(config-cross-connect)("SFP200")# outer vid 200 Specify user VLAN for the given service LTP-X(config-cross-connect)("SFP200")# user vid 200 LTP-X(config-cross-connect)("SFP200")# exit Create and switch to profile for the SFP-ONU LTP-X(config)# profile ports SFPONU Add port 0 to bridge group 20 LTP-X(config-ports)("SFPONU")# port 0 bridge group 20 Apply the configuration LTP-X(config-ports)("SFPONU ")# do commit |
Save the configuration LTP-X(config-ports)("SFPONU ")# do save |
Adding and configuring ONT SFP-ONU.
Go to the configuration mode LTP-X# configure terminal Go to tree 0 ONT ID 3 LTP-X(config)# interface ont 0/3 Assign the required ONT to this position LTP-X(config)(if-ont-0/3)# serial 454C545862000078 Assign ports SFPONU profile LTP-X(config)(if-ont-0/3)# profile ports SFPONU Assign cross-connect SFP-ONU profile LTP-X(config)(if-ont-0/3)# service 0 profile cross-connect SFP100 Assign default DBA profile LTP-X(config)(if-ont-0/3)# service 0 profile dba dba-00 Assign cross-connect SFP-ONU profile LTP-X(config)(if-ont-0/3)# service 1 profile cross-connect SFP200 Assign default DBA profile LTP-X(config)(if-ont-0/3)# service 1 profile dba dba-00 Apply the configuration LTP-X(config)(if-ont-0/3)# do commit |
Configuration example for transmission via ONT SFP-ONU VLANs in TRUNK mode, several VLANs in Selective-tunnel mode and other VLANs in Tunnel mode
In firmware versions older than 3.26.0, it is possible to organize the trunk tunnel services through SFP-ONU.
VLAN 300 (multicast) and QinQ VLAN 1100 and 1200 (Internet) come to the uplink OLT. It is necessary to let them pass to the switch integrated in the OLT via SFP-ONU.
Consider the procedure of OLT configuration for the above diagram.
Step 1. Configure the switch.
LTP-X(switch)(config)# vlan 300,1100,1200 LTP-X(switch)(config-vlan-range)# tagged pon-port 0 LTP-X(switch)(config-vlan-range)# front-port 0 LTP-X(switch)(config-vlan-range)# commit |
Step 2. Configure cross-connect profiles.
LTP-X(config)# profile cross-connect cc-tunnel LTP-X(config-cross-connect)("cc-tunnel")# bridge LTP-X(config-cross-connect)("cc-tunnel")# bridge group 10 LTP-X(config-cross-connect)("cc-tunnel")# tag-mode tunnel LTP-X(config-cross-connect)("cc-tunnel")# exit LTP-X(config)# profile cross-connect "cc-selecttunnel" LTP-X(config-cross-connect)("cc-selecttunnel")# bridge LTP-X(config-cross-connect)("cc-selecttunnel")# bridge group 10 LTP-X(config-cross-connect)("cc-selecttunnel")# tag-mode selective-tunnel LTP-X(config-cross-connect)("cc-selecttunnel")# exit LTP-X(config)# profile cross-connect "cc-single" LTP-X(config-cross-connect)("cc-single")# bridge LTP-X(config-cross-connect)("cc-single")# bridge group 10 LTP-X(config-cross-connect)("cc-single")# user vid 300 LTP-X(config-cross-connect)("cc-single")# exit |
Step 3. Configure ports profiles.
LTP-X(config)# profile ports bridge-10 LTP-X(config-ports)("bridge-10")# port 0 bridge group 10 |
Step 4. Configure address-table profile by specifying the VLANs used for tunnels and assign the profile to GPON ports.
LTP-X(config)# profile address-table at-tunnel LTP-X(config-address-table)("at-tunnel")# s-vlan 1100 use c-vlan LTP-X(config-address-table)("at-tunnel")# s-vlan 1200 use c-vlan LTP-X(config-address-table)("at-tunnel")# exit LTP-X(config)# interface gpon-port 0 LTP-X(config)(if-gpon-0)# profile address-table at-tunnel |
Step 5. Configure SFP-ONU to be used for switch connection.
LTP-X(config)# interface ont 0/0 LTP-X(config)(if-ont-0/0)# serial "454C545300000001" LTP-X(config)(if-ont-0/0)# service 0 profile cross-connect cc-tunnel dba dba-00 LTP-X(config)(if-ont-0/0)# service 1 profile cross-connect cc-selecttunnel dba dba-00 LTP-X(config)(if-ont-0/0)# service 2 profile cross-connect cc-single dba dba-00 LTP-X(config)(if-ont-0/0)# profile ports "bridge-10" LTP-X(config)(if-ont-0/0)# service 0 custom svid 1100 LTP-X(config)(if-ont-0/0)# service 1 custom svid 1200 LTP-X(config)(if-ont-0/0)# service 1 selective-tunnel uvid 201-203 LTP-X(config)(if-ont-0/0)# service 2 custom svid 300 |
ONT status description
ONT status | Description |
---|---|
UNACTIVATED | ONT has no configurations |
ALLOCATED | ONT detected |
AUTHINPROGRESS | ONT authentication is in progress |
AUTHFAILED | Authentication failed |
AUTHOK | Authentication successfully completed |
PRECONFIG | Preparing ONT for configuration |
CFGINPROGRESS | ONT configuration is in progress |
CFGFAILED | Configuration failed |
OK | ONT is in operation |
BLOCKED | ONT is blocked |
MIBRESET | ONT MIB reset |
FAILED | ONT has a critical failure |
FWUPDATING | ONT firmware update is in progress |
DISABLED | ONT is disabled (technically blocked) |
GPON interface states
Value | Description |
---|---|
INITED | The channel is initialised |
CFGINPROGRESS | The channel configuration is in progress |
CFGFAILED | The channel configuration completed with error |
OK | The channel is in operation |
FAILED | The channel is out of operation |
DISABLED | The channel is disabled |
TECHNICAL SUPPORT
For technical assistance in issues related to handling Eltex Ltd. equipment, please, address to Service Center of the company:
Feedback form on the website: https://eltex-co.com/support/
Servicedesk: https://servicedesk.eltex-co.ru
Visit ELTEX official website to get the relevant technical documentation and software for Eltex Ltd. equipment:
Official website: https://eltex-co.com/
Download center: https://eltex-co.com/support/downloads