...
Предупреждение |
---|
Warnings are used to inform the user about situations that may cause harm to a software and hardware complex, lead to malfunction or data loss. |
LTP-X EasyMode description
EasyMode is a function set of LTP optical terminals. EasyMode is dedicated to fast GPON deployment according to realized service model. EasyMode allows providers to configure Triple Play services promptly.
...
- Acquaintance with GPON technology and ELTEX equipment;
- Fast testing of the main capabilities of the equipment;
- Automatic configuring of the equipment on a network.
Software and hardware requirements
The EasyMode is supported by the hardware of B and C revisions and by NTU terminals. EasyMode operation requires the firmware version not lower than:
For LTP-8X(4X) | 3.26.1 |
For NTU-1 | 3.24.0 |
For NTU-2W | 3.25.1 |
For NTU-2V(C), NTU-RG-1402G-W | 3.25.2 |
For NTU-RG-1421(31)G-Wac | 3.28.1 |
Installation and connection
To get acquainted with device hardware, installation and connection methods, refer to LTP user manual on the website.
Connection to the terminal
Connection to LTP is possible either with a console cable or with an Ethernet cable to the GE port.
Console cable connection
For LTP rev.B, the RS-232 cable DB9(F) – DB9(F), which is included in the delivery package, is used. The port is located on the left side of the front panel, as shown in Figure 1.
...
Table 1 — Description of connectors, LEDs and controls located on the front panel of LTP rev.B
# | Front panel element | Description | |
---|---|---|---|
1 | Console | RS-232 console port for local control of the device | |
2 | GE Port 0..3 | 4 RJ-45 connectors of 10/100/1000BASE-T Gigabit uplink interfaces for connection to IP networks (for LTP-8X) | |
3 | Combo GE | 0..3 | 4 chassis for SFP modules of 1000BASE-X uplink interface for connection to IP networks (for LTP-4X) |
4 RJ-45 connectors of 10/100/1000BASE-T Gigabit uplink interfaces for connection to IP networks (for LTP-4X) | |||
4..7 | 4 chassis for SFP modules of 1000BASE-X uplink interface for connection to IP networks (for LTP-8X) | ||
4 RJ-45 connectors of 10/100/1000BASE-T Gigabit uplink interfaces for connection to IP networks (for LTP-8X) | |||
4 | 10G/1G 0..1 | 2 chassis for SFP modules of 10GBASE/1000BASE-X uplink interface for connection to IP networks | |
5 | PON | 4 chassis for SFP modules of xPON 2.5 G (for LTP-4X) | |
8 chassis for SFP modules of xPON 2.5 G (for LTP-8X) | |||
6 | Power | Device power indicator | |
7 | Status | Device operation indicator | |
8 | F | Functional key that reboots the device and resets it to factory default configuration:
Configuring the response to a button click is done in the CLI of the terminal. |
Table 2 lists connectors, LEDs and controls located on the front panel of LTP rev.C/rev.D.
Table 2 — Description of the connectors, LEDs, and controls located on the front panel of LTP rev.C/rev.D
# | Front panel element | Description | |
---|---|---|---|
1 | Power | Device power indicator | |
2 | Status | Device operation indicator | |
3 | Fan | Fan operation LED | |
4 | RPS | Redundant power supply LED | |
5 | Console | Console port for local management of the device.
| |
6 | F | Functional key that reboots the device and resets it to factory default configuration:
Configuring the response to a button click is done in the CLI of the terminal. | |
7 | GE Port 0..3 | 4 RJ-45 connectors of 10/100/1000BASE-T Gigabit uplink interfaces for connection to IP networks (for LTP-8X) | |
8 | Combo GE | 0..3 | 4 chassis for SFP modules of 1000BASE-X uplink interface for connection to IP networks (for LTP-4X) |
4 RJ-45 connectors of 10/100/1000BASE-T Gigabit uplink interfaces for connection to IP networks (for LTP-4X) | |||
4..7 | 4 chassis for SFP modules of 1000BASE-X uplink interface for connection to IP networks (for LTP-8X) | ||
4 RJ-45 connectors of 10/100/1000BASE-T Gigabit uplink interfaces for connection to IP networks (for LTP-8X) | |||
9 | 10G/1G 0..1 | 2 chassis for SFP modules of 10GBASE/1000BASE-X uplink interface for connection to IP networks | |
10 | PON | 4 chassis for SFP modules of xPON 2.5 G (for LTP-4X) | |
8 chassis for SFP modules of xPON 2.5 G (for LTP-8X) |
Connect the cable and configure the following connection parameters:
...
Default username and password: admin/password.
Scroll Pagebreak
Connection via Telnet/SSH
Connect the Ethernet cable to any of the GE/ComboGE ports. By default, the IP address of the LTP management interface — 192.168.1.2/24. Configure an address 192.168.1.1 on your computer and subnet mask 255.255.255.0 as it shown in Figure 4.
...
Default username and password: admin/password.
Service model in EasyMode
The EasyMode includes a prepared configuration for the network, a diagram of which is shown in Figure 5.
...
- Internet service using IPoE technology. It is possible to add option 82 specified by you to DHCP packets.
- "VLAN on service" model. Subscribers of one service are in the same VLAN.
- User isolation. There is no connectivity between subscribers at the channel level.
- Dedicated multicast VLAN. Unicast services: IPTV (Video-On-Demand, VoD) are spaced from multicast traffic.
- Multicast traffic is available for all ports of subscriber terminal.
EasyMode enabling and configuration
Примечание |
---|
Enabling EasyMode will lose the current configuration. Save it if you may need it later. |
EasyMode can be used with the values you specify or with default values.
Default configuration
Parameters to be applied by default:
IP address for LTP management | 192.168.1.2 |
Subnet mask | 255.255.255.0 |
Management VLAN | 1 |
Gateway in management network | none |
ACS VLAN (built-in TR-069 server) | 2 |
Internet VLAN | 100 |
VoIP VLAN | 200 |
VoD VLAN | 300 |
Multicast VLAN | 400 |
Option82 Circuit-Id | none |
Option82 Remote-Id | none |
To enable EasyMode with default values, you should execute the easy-mode command. After that, a warning will be displayed stating that the current configuration of the device will be lost.
...
After that, you can proceed to sections 6.3 and 7 of this manual.
Scroll Pagebreak |
---|
Примечание |
---|
To view ONT configurations added automatically, previously enter the rollback command. Until the command is entered, changes will not be displayed in the current session. |
Custom configuration
You can change the settings of the LTP management interface, service VLANs and parameters of DHCP option 82 using the Wizard. In addition, you can quickly add already connected subscriber terminals and after completing the configuration, get a network ready for operation.
To start working with Wizard, you need to execute the easy-mode wizard command. After that, a warning will be displayed stating that the current configuration of the device will be lost.
Блок кода | ||
---|---|---|
| ||
LTP-4X# easy-mode wizard Enabling easy-mode will delete current configuration. Are you sure? (y/n) y Customize easy-mode configuration: < … > |
VLAN Configuration
Specify the VLANs you want to use for the services. VLAN data will be automatically registered tagged to all Ethernet ports, with the exception of VLANs for the built-in ACS server.
If all the default values are correct, you can refuse the change by responding N to the invitation to change. If the default value for a single service is correct, you can skip input by simply pressing <Enter>.
As an example, change the VLAN as follows:
...
Блок кода | ||
---|---|---|
| ||
Current VLAN configuration: ACS VLAN ID: 2 Internet VLAN ID: 100 VoIP VLAN ID: 200 VoD VLAN ID: 300 Multicast VLAN ID: 400 Do you want to change VLAN configuration? (y/N): y Enter ACS service VLAN ID (leave blank for default) [2]: Enter Internet service VLAN ID (leave blank for default) [100]: 1001 Enter VoIP service VLAN ID (leave blank for default) [200]: 1002 Enter VoD service VLAN ID (leave blank for default) [300]: 1003 Enter Multicast VLAN ID (leave blank for default) [400]: 3 |
Configuration of the LTP management interface
In the next section, you can change the access settings for LTP. If you are satisfied with the default value, reply N to the change prompt. If you are satisfied with the default value for a single parameter, you can skip input by simply pressing <Enter>.
As an example, change the management settings as follows:
...
In this case, you need to select a different IP subnet.
DHCP Relay Agent (option 82) configuration
The last configuration step — DHCP option 82 configuration for substitution into packets from subscribers. By default, option substitution is disabled. If option 82 is not used on your network, you can skip configuring it by answering N to the prompt to change.
When enabling option substitution, the following values of the Circuit-Id and Remote-Id suboptions are used:
...
Блок кода | ||
---|---|---|
| ||
Do you want to use option 82? (y/N): y Current configuration dhcp-ra overwrite-option 82: Circuit id: %HOSTNAME%-%PONSERIAL%-%VLAN0% Remote id: - Do you want to setup Option 82 format? (answer No for default option) (y/N): y Enter Circuit ID (leave blank for empty option): %GPON-PORT%-%ONTID% Enter Remote ID (leave blank for empty option): %MNGIP% |
Saving configuration
After applying the new configuration, the following message will be displayed.
...
Блок кода | ||
---|---|---|
| ||
LTP-4X# save ........ Configuration successfully saved to file |
Adding new ONTs
Automatic ONT activation configuration
In the simplified setup mode, the ONT auto-activation mode is enabled, and the required ONT configuration is applied automatically from the corresponding auto-activation template. These templates were created when EasyMode was enabled. For NTU-1, which are controlled using OMCI protocol only, the easy-ONT template is used. For all other ONTs, the easy-RG template is used.
...
Примечание |
---|
To view ONT configurations added automatically, enter the rollback command. Until the command is entered, changes will not be displayed in the current session. |
Manual ONT activation
After enabling and configuring EasyMode, in order to add new connected ONTs into the configuration, you need to:
...
Примечание |
---|
After applying the settings, the subscriber terminals will reboot with the new configuration. The old one will be deleted. |
Scroll Pagebreak |
---|
Consider configuring ONT RG parameters using the internal ACS on the basis of VoIP settings. For more information about working with ACS, refer to the Eltex ACS User manual, which can be found at the link.
Configure for the ONT 454C545866000101 the number 101 with the secret password on the SIP server sip.test.pon. For this purpose, do the following:
Execute the acs command to operate with the built-in ACS server.
Блок кода language xml LTP-4X# acs LTP-4X(acs)#
Switch to the ONT configuration mode and select the desired ONT by serial number using the ont and ont 454C545866000101 commands.
Блок кода language xml LTP-4X(acs)#ont LTP-4X(acs-ont)#ont 454C545866000101 LTP-4X(acs-ont-sn='454C545866000101')#
Set private parameters for enabling the phone line, SIP server address, numbers and passwords.
Блок кода language xml LTP-4X(acs-ont-sn='454C545866000101')#set private sip_proxy sip.test.pon Host property has been updated: 'InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.SIP.UserAgentDomain' = 'sip.test.pon' Host property has been updated: 'InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.SIP.RegistrarServer' = 'sip.test.pon' Host property has been updated: 'InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.SIP.ProxyServer' = 'sip.test.pon' Host property has been updated: 'InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.SIP.OutboundProxy' = 'sip.test.pon' Ok LTP-4X(acs-ont-sn='454C545866000101')#set private voice1_enable TRUE Host property has been updated: 'InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1.Enable' = 'TRUE' Ok LTP-4X(acs-ont-sn='454C545866000101')#set private voice1_number 101 Host property has been updated: 'InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1.SIP.AuthUserName' = '101' Host property has been updated: 'InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1.DirectoryNumber' = '101' Host property has been updated: 'InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1.CallingFeatures.CallerIDName' = '101' Host property has been updated: 'InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1.SIP.URI' = '101' Ok LTP-4X(acs-ont-sn='454C545866000101')#set private voice1_password secret Host property has been updated: 'InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1.SIP.AuthPassword' = 'secret' Ok
Scroll Pagebreak Apply the changes with the commit command and reconfigure the ONT with the reconfigure command.
Блок кода language xml LTP-4X(acs-ont-sn='454C545866000101')#commit LTP-4X(acs-ont-sn='454C545866000101')#reconfigure Ok LTP-4X(acs-ont-sn='454C545866000101')#
Exit the ACS mode using the exit command.
Блок кода language xml LTP-4X(acs-ont-sn='454C545866000101')#exit LTP-4X(acs-ont)#exit LTP-4X(acs)#exit LTP-4X#
Using a predefined ONT configuration without EasyMode
If you are not satisfied with the proposed EasyMode service model, you can only use the predefined ONT configuration by configuring LTP by yourself, according to your needs.
...
Блок кода | ||
---|---|---|
| ||
LTP-4X# configure terminal LTP-4X(config)# interface ont 2/2 LTP-4X(config)(if-ont-2/2)# no easy-mode LTP-4X(config)(if-ont-2/2)# exit LTP-4X(config)# exit LTP-4X# commit Changes successfully commited (1 chunk) LTP-4X# send omci restore interface ont 2/2 [ONT2/2] was successfully restored to default config and rebooted |
Scroll Pagebreak |
---|
TECHNICAL SUPPORT
For technical assistance in issues related to handling Eltex Ltd. equipment, please, address to Service Center of the company:
...