История страницы

...

...

|| DeviceType | Base station |
|| DeviceName | WOP-2ac-LR5 |
|| DocTitleMain |  |
|| DocTitleAdditional | User Manual |
|| fwversion | 1.45.20 |
|| issueDate | 0104.2020 |
|| ipaddr | 192.168.1.10 |
|| username | admin |
|| password | password |

...

• centralized authorization via RADIUS server (WPA Enterprise);
• WPA/WPA2 data encryption;
• 64/128/152-bit WEP data encryption;

Fig. 1 shows an operation diagram for WOP-2ac-LR5.

Technical Features

Table 1 shows main specifications of the device.

...

WOP-2ac-LR5 housed in a plastic case, industrial version. The size of the device: 80x232.5x47 mm. The appearance of WOP-2ac-LR5 is shown in the Fig. 2.

A combo port 10/100/1000Base-T (Ethernet)/100/1000Base-X (SFP) for local network connection and power supply via PoE, a grounding terminal (for WOP-2ac-LR5 H/W version 1v5 and higher; for WOP-2ac-LR5 rev.B) and a factory reset button (F) are located under the cover at the bottom of the device, Fig. 3.

...

The appearance of WOP-2ac-LR5 indication panel is shown in the Fig. 4.

Fig. 4 – WOP-2ac-LR5 indication panel appearance

The current state of the device is shown with the help of light indicators located on the front panel of WOP-2ac-LR5. The list of indicators and their description are given in the table 2.

...

1. Attach the bracket to the device with the screws provided, as shown in the figure below.

   

2. Install the device on communications mast/pole with Ethernet port down as it is shown in the figure below. Attach the device using clamps supplied in the device package. Follow the safety rules and recommendations given in Safety rules and Installation recommendations.

   
   

   

   
   

3. Remove the cover that closes the Ethernet port on the bottom panel of the device. Ground the device using a grounding connector (for H/W version: 1v5 and higher), then connect the Ethernet cable to the PoE port. When building a network over fiber, install the transceiver and make the connection.
   

   

4. Close the bottom cover.
5. Connect the antenna to the device using the cable assemblies.
6. Adjust the position of the antenna so that subscriber devices fall into the coverage area of the installed antenna.
7. Connect the Ethernet cable coming from WOP-2ac-LR5 to the PoE port or the injector or switch (IEEE 802.3at-2009).
8. If you use a PoE injector, connect it to 220 V power supply network using the cable.
9. Adjust the antenna more precisely using light indicators on the device.

...

In the 'Radio' submenu, the device radio interface's parameters are configured.Image Removed

Image Added

• Mode – interface operation mode:
  • IEEE 802.11a
  • IEEE 802.11a/n
  • IEEE 802.11a/n/ac
• Channel – data channel selection;
• Channel Bandwidth, MHz – bandwidth of a channel on which the base station operates. The parameter may take values of 5, 10, 20, 40 and 80 MHz. Note that channel bandwidth of 80 MHz will operate only according to 802.11ac standard. If the base station has 5 or 10 MHz bandwidth, select the same bandwidth on the user station;
• Fixed center frequency – when the flag is checked, all traffic (data and management packets) will be transmitted at the specified channel center frequency with a given bandwidth (40 or 80 MHz). The function is proprietary, transmission is not carried out according to IEEE 802.11 standards, where it is supposed to use different center frequencies for data and management traffic with 40/80 MHz bandwidth.
• Tx Power (dBm) – Wi-Fi transmitter signal strength adjustment, dBm.
• Fixed Transmit Rate – fixed wireless data transmission rate defined by IEEE 802.11a/n/ac standards;
• ACK Timeout, µs – waiting time for packet delivery confirmation from the subscriber.
• Polling – when checked, the option is enabled, otherwise – disabled. Polling is an option for TDM access to the medium (time division). It is characterized by a constant customer survey by the BS
  • MAX TX Duration, ms – time indicating how long the subscriber station can transmit traffic.
  • Management packet modulation – fixed rate for management packets.

...

...