...

|| DeviceType | IP camera |
|| DeviceName | SV-BA301-E |
|| DocTitleAdditional | User manual |
|| fwversion | Version 1.6.0 |

Notes and warnings

Product description

SV-BA301-E is a camera designed for real-time video surveillance. Due to the QuadHD resolution, the transmitted image is clear and detailed. PoE technology allows installing the camera everywhere, regardless of the location of the power supply. It also saves on the cost of power cables and makes the installation simple and not time-consuming.

Features and capabilities:
– Night vision provides clear images even in low-light conditions.
– Motion detection notifies you of events as they occur.
– Video archive provides options for saving recordings: to a memory card for local storage or to network storage¹. If the local storage fails, all recordings will remain available on the network storage.
– PoE power supply.

Technical specifications

Design

Front view

The front view of the camera is shown in the figure below.

Image Modified

Top view

The top view of the camera is shown in the figure below.

Image Modified

Side view

A side view of the camera is shown in the figure below.

Image Modified

Bottom view

The bottom view of the camera is shown in the figure below.

Image Modified

Base view

The base view of the camera is shown in the figure below.

Image Modified

Cable design

Image Modified

Light indication

Якорь
leds leds

Delivery package

SV-BA301-E standard delivery package includes:

• SV-BA301-E IP camera;
• Mounting kit;
• Case mounting template;
• Installation and initial configuration guide.

Reset to factory settings

Якорь
reset reset

 

There are two ways to perform a factory reset:

• Software reset. In the device web interface, enter "System settings", select "Configuration" and click "Reset to Factory Default Settings".
• Hardware reset. The reset button is located on the cable. Remove the protective cap, then press and hold the reset button for three seconds. The camera will then reboot.

Operating conditions

• The camera is designed for indoor and outdoor usage.
• Do not install the device near heat sources.
• Do not expose the device to smoke, dust, water or other liquids. Do not mechanically damage the device.
• Do not open the device case. There are no user-serviceable elements inside the camera.
• At the end of its service life, do not dispose of the camera with normal household waste. Take it to an electronics recycling center.

Device installation

Selecting the camera location

Якорь
place place

1. Determine the areas that need to be monitored. Consider that entrance doors, windows, and various objects may obstruct the camera's field of view and reduce it.
2. Pay attention to the lighting where the camera is installed to ensure a clear image. Avoid direct sunlight and other bright light sources directed at the camera lens. Also consider light sources that may create shadows or glare in the image.
3. Consider the location of the power supply. The use of extension cords or additional cables is not recommended, as this may impair the quality of the power supply.

Mounting using a bracket

1. Select a location for the camera based on the recommendations in the "Selecting a camera location" section.
2. On the selected surface, mark where the four holes for the bracket will be drilled. Use the supplied template for this purpose.

Image Modified

3. Separate the template from the backing and stick it to the wall.

Image Modified

4. Drill four holes according to the template. Use dowels if necessary.

Image Modified

5. Align the holes on the wall with the holes on the bracket and fix the camera with screws.

Image Modified
  A view of the camera placed on the ceiling is shown in the figure below.
Image Modified

6. Connect the Ethernet cable in the order shown in the image below: slide the O-ring (2) over the sealing cap of the network interface (1). Place the locking nut (6) and the cable gland (4) on the Ethernet cable (3). Insert the Ethernet cable (3) into the network interface. Tighten the cable gland (4) and fix it to the sealing cap (1). Slide the waterproof ring (5) over the sealing ring (4). Make sure that the ring fits snugly over the connector. Tighten the locking nut (6) and fix it to the cable gland(4). Once the Ethernet cable is connected and insulated, connect the power cable to the power connector (7).  
Image ModifiedThe assembled cable is shown in the figure below.

Device management via the web interface

Getting started

1. Connect the camera to the local network.

2. Open a web browser and enter the device's IP address obtained from the DHCP server in the address bar.

The authorization page will be displayed in the browser window. Enter the username and password in the appropriate fields. (By default, the login is admin, the password is password).
Image Modified

      3. Click the "Sign in" button. The "Watch" page will open in the browser window.

"Watch" tab

Image Modified

• Streams:
  • Main — main stream, has better broadcast quality;
    
  • Sub — secondary stream, has average broadcast quality;
    
  • Mob — mobile stream, has low broadcast quality.

"Archive" tab

Image Modified

• Filtration — searching for records by specified parameters.
  • Time from — filtering media files recorded starting from the specified date and time;  
  • Time to — filtering media files recorded up to the specified date and time;  
  • Record mode:
    • All — displaying all media files;  
Постоянная запись
• • • Permanent recording — displaying media files with the "
Continuous
• • • Permanent recording" mode;  
Запись по событиям —
• • • Event recording — displaying media files with the "Event recording" mode.
  • Event:
    • All — displaying all media files;  
Движение —
• • • Motion — displaying media files with the "Motion" recording mode.

"Settings" tab

"Device Information" menu

Image Modified

1. Menu tabs — for grouping by categories: Watch, Archive, Settings; 
2. Web interface theme — dark and light; 
3. Username;
4. Web interface help;
5. Web interface language;
6. Logout;
7. Menu items;
8. Device information:
   • Model — device model name;
   • Serial Number — device serial number;
   • MAC Address — device MAC address;
   • Firmware version — current device firmware version.

"System Settings" tab

"Date And Time"

Image Modified

• Time — camera time. Can be edited if synchronization is not enabled;
• Timezone — camera time zone;
• NTP Server — NTP server address;
• NTP Server Synchronization — enabling NTP synchronization.

To save the settings, click the "Apply" button.

"Configuration"

Image Modified

• Configuration — section for working with the device configuration:
  
  • Load the Device Configuration from a File — select the file from which the camera will load its configuration;
  • Save the Device Configuration to a File — export the device configuration for further use.
• Reboot By Timer — section for configuring automatic weekly reboot:
  
  • Day — the day of the week when the reboot will occur;
  • Time — the exact time when the reboot will occur.
• Device Management: 
  • Reboot Device;
  • Reset to Factory Default Settings.

To save the settings, click the "Apply" button.

"Users Settings"

Image Modified

• Users Settings — creating a camera user for interaction with the web interface:
  • User Name —  user login;
  • Password — user password;
  • Group Name — group with specific access rights;
  • Actions: 
    • Edit — change existing user parameters;
    • Remove — delete user.
• Group Settings — group and access rights settings:
  • Group Name — group name;
  • Actions: 
    • Edit — change existing user parameters;
    • Remove — delete group.

"Firmware Upgrade"

Image Modified

• Firmware URI — URI link from which the camera can download the firmware for updating.

To start the update, press the "Start Upgrading" button.

"Video/Audio Settings"

"Stream Settings"

Image Modified

• Streams:
  • Main — main stream, has the best broadcast quality;
    
  • Secondary — secondary stream, has average broadcast quality;
    
  • Mobile — mobile stream, has low broadcast quality.
    
• Stream params:
  • Resolution —  selection of the image resolution transmitted from the camera:
    • 1280 × 720;
    • 1920 × 1080;
    • 2560 × 1440.
  • Codec — selection of the video compression standard:
    • H.264;
    • H.265.
  • Frames per second — number of frames that will be transmitted per second. The maximum frequency is 25 frames per second;
    
  • Rate control mode — stream encoding mode:
    
    • Constant bitrate — mode in which the stream has a constant bitrate set in the "Bitrate" field;
Переменный битрейт —
• • • Variable bitrate — mode in which the stream has a variable bitrate. The bitrate varies with the complexity of the image but does not exceed the "Maximum bitrate" value and on average adheres to the "Bitrate" value.
  • Bitrate — amount of information transmitted by the camera. Increasing this parameter proportionally increases the quality of the transmitted image. Maximum bitrate — 6000 kbps.
    

To save the settings, click the "Apply" button.

"RTSP Settings"

Image Modified

• Streams:
  • Main — main stream, has the best broadcast quality;
    
  • Secondary — secondary stream, has average broadcast quality;
    
  • Mobile — mobile stream, has low broadcast quality.

• Sream params — section for configuring RTSP streaming:
  
  • Audio —  enable and disable audio in the stream;
    
  • Enabled — enable and disable the stream;
    
  • Stream URL — link to the selected stream considering the fields "Login", "Password", and "Port" in the "Common params" section;
    
• Common params: 
  • Login — username up to 63 characters in Latin alphabet and numbers;
  • Password — user password up to 63 characters in Latin alphabet and numbers;
  • Port — port through which the stream can be obtained from the RTSP server.

To save the settings, click the "Apply" button.

"Audio Settings"

Image Modified

• Mic enable — enabling and disabling the microphone;
• Volume — microphone volume. Maximum value — 150 dB;
• Gain — microphone volume gain. Maximum value — 31 dB;
• Denoise mode:
  • Off — noise damping off;
  • Low — low noise damping;
  • Medium — medium noise damping;
  • High — high noise damping;
  • Max — maximum noise damping.
• AGC enable:
  • Volume — automatic microphone gain volume;
  • Gain — microphone volume gain.

To save the settings, click the "Apply" button.

"Sensor Settings"

Image Modified

• IR settings:
  • IR brightness;
  • Enable IR:
    • off:
    • on;
    • auto.
  • Day&Night —
выбор режима инфракрасной подсветки
• • selection of infrared illumination mode:
    • Auto —
автоматическое переключение между дневным и ночным режимом по уровню освещенности
• • • automatic switching between day and night mode based on light level;
    • Day —
инфракрасная подсветка всегда выключена
• • • infrared illumination is always off;
    • Night —
инфракрасная подсветка всегда включена
• • • infrared illumination is always on.
• Image settings:
  • Contrast —
контраст изображения. Возможно задать значение в диапазоне от 0 до 255. Значение по умолчанию —
• • image contrast. It is possible to set a value in the range from 0 to 255. The default value is 128;
  • Sharpness —
резкость изображения. Возможно задать значение в диапазоне от 0 до 255. Значение по умолчанию —
• • image sharpness. It is possible to set a value in the range from 0 to 255. The default value is 90;
  • Saturation —
красочность изображения. Возможно задать значение в диапазоне от 0 до 255. Значение по умолчанию —
• • image saturation. It is possible to set a value in the range from 0 to 255. The default value is 128;
  • Brightness —
яркость изображения. Возможно задать значение в диапазоне от 0 до 255. Значение по умолчанию —
• • image brightness. It is possible to set a value in the range from 0 to 255. The default value is 128;
  • White balance —
используется для регулировки цветовой температуры в зависимости от окружающей среды
• • used to adjust the color temperature depending on the environment: 
    • auto —
автоматическая настройка
• • • automatic configuration;
    • day —
дневной свет
• • • daylight;
    • cloud —
облачно
• • • cloudy;
    • inc —
лампа накаливания
• • • incandescent lamp;
    • fluo —
флуоресцентный свет
• • • fluorescent light;
    • twi —
сумерки
• • • twilight;
    • shade —
тень
• • • shade;
    • warm_fluo —
теплый флуоресцентный свет
• • • warm fluorescent light. 
  • Image orientation —
управление изображением камеры
• • camera image management:
    • Default —
камера передает изображение так, как пользователь его видит своими глазами
• • • camera transmits the image as the user sees it with their own eyes;
    • Vertical Flip —
изображение отражается по вертикальной оси
• • • image is reflected along the vertical axis;
    • Horizontal Flip —
изображение отражается по горизонтальной оси
• • • image is reflected along the horizontal axis;
    • 180 Rotation —
изображение отражается по вертикали и горизонтали, тем самым предоставляя изображение как в режиме «Стандартная» для физически перевернутой камеры
• • • image is reflected vertically and horizontally, thus providing an image as in "Standard" mode for a physically inverted camera.

Image Modified

• Image enhancement:
  • Antiflicker — compensation for lamp flicker from power grids of different frequencies: 
    • off;
    • 50 Hz;
    • 60 Hz.
  • Backlight compensation — elimination of darkening when the object is against a bright light source. It is possible to set a value in the range from 0 to 10;
  • 2D Denoiser — noise damping in each frame by analyzing neighboring pixels. It is possible to set a value in the range from 0 to 255. Default value — 128;
  • 3D Denoiser — noise damping by analyzing both neighboring pixels and changes between frames. It is possible to set a value in the range from 0 to 255. Default value — 128;
  • Defog — increasing image clarity and contrast in poor visibility conditions caused by fog or haze:
    • Strength — it is possible to set a value in the range from 0 to 255.
• DWDR:
  • Enable WDR — improving image visibility with any lighting level fluctuations:
    • Strength — degree of brightening dark areas. It is possible to set a value in the range from 0 to 255;
    • Hilight — degree of suppression of bright areas. It is possible to set a value in the range from 0 to 10.

"OSD parameters"

Image Modified

• OSD — On-Screen Display, text displayed on the screen;
  • Text:
    • Show — enable the display of user text;
    • Transparency — transparency of the displayed text. It is possible to set a value in the range from 0 to 255;
    • Text — field for entering text to display.
  • Date:
    • Show — enable the display of the date;
    • Transparency — transparency of the displayed date. It is possible to set a value in the range from 0 to 255.

"Network Settings" menu

"Network"

Image Modified

Image Modified

• Mode:
  • Auto — obtaining all settings via DHCP;
  • Manual — setting all network parameters manually:
    • IP Address;
    • Network Mask;
    • Dns List — addresses of DNS servers;
    • + — adding a backup DNS server;
    • Default Gateway.

To save the settings, click the "Apply" button.

"ONVIF Settings"

Image Modified

• Enabled — enabling the ONVIF protocol;
• Port — port through which the camera will interact with control systems via the ONVIF protocol. By default, port 1000 is used;

• Users — creating users with specific access rights:
  • Login — user login;
  • Password — user password;
  • Rights — user access level:
    • Administrator — full access to all device functions;
    • Operator — access to basic device functions. Cannot change settings or manage users;
    • Media user — limited access (view only). No rights to change configuration;
    • Anonymous — minimal rights (if allowed in settings). Usually view only without authorization.

To save the settings, click the "Apply" button.

"Additional Settings"

Image Modified

• Enable HTTP Server — access to the camera's web interface via the HTTP protocol;
• HTTP Port — port through which interaction with the camera's web interface via the HTTP protocol will be carried out. By default, port 80 is used;

• Enable HTTPS Server — access to the camera's web interface via the HTTPS protocol;
• HTTPS Port — port through which interaction with the camera's web interface via the HTTPS protocol will be carried out. By default, port 443 is used.

To save the settings, click the "Apply" button.

"System Log"

Image Modified

• Download log — download system log;
• Remote logging — section for configuring logs to a remote server:
  
  • Syslog server — address of the remote syslog server.

To save the settings, click the "Apply" button.

"Archive Settings" menu

"Schedule"

Image Modified

• Schedule — setting the period during which the camera will record. To select the necessary intervals, highlight them by clicking the left mouse button.

To save the settings, click the "Apply" button.

"Record Parameters"

Image Modified

• Streams:
  • Main — main stream, has the best broadcast quality;
    
  • Secondary — secondary stream, has average broadcast quality;
    
  • Mobile — mobile stream, has low broadcast quality.
• Record:
  • Permanent recording —
видеозапись ведется постоянно
• • video recording is permanent;
  • Event recording
— видеозапись ведется только при обнаружении события;
• • — video recording occurs only when an event is detected;
  • Off — video recording is not conducted
Off — видеозапись не ведется
• • .
• Maximum number of events
 — сохранение установленного числа событий на MicroSD-карту. При превышении числа событий старые записи будут перезаписываться. Возможно задать значение в диапазоне от 0 до
• — saving a set number of events to a MicroSD card. If the number of events is exceeded, old recordings will be overwritten. It is possible to set a value in the range from 0 to 10000;
• Record sound
 — включение/выключение микрофона во время записи.
• — enable/disable the microphone during recording.

To save the settings, click the "Apply" buttonДля сохранения настроек нажмите кнопку «Применить».

"Storage Settings" menu

Image Modified

...

• Percentage of storage space allocated for video recordings, % —
указание, какая часть общего объема накопителя будет использоваться для хранения видео. Возможно задать значение в диапазоне от 0 до 100;  
• indicates what part of the total storage volume will be used for storing video. It is possible to set a value in the range from 0 to 100;  
• Percentage of volume for
Percentage of volume for
• event recordings (from the allocated volume for video recordings), % —
указание, сколько места из этого объема будет выделено для записи по событиям. Возможно задать значение в диапазоне от 0 до
• indicates how much space from this volume will be allocated for event recordings. It is possible to set a value in the range from 0 to 100;
• Enable record loop
 — при заполнении накопителя старые записи будут перезаписаны новыми.

• — when the storage is full, old recordings will be overwritten with new ones.

To save the settings, click the "Apply" buttonДля сохранения настроек нажмите кнопку «Применить».