...
Предупреждение |
---|
Warnings are used to inform the user about harmful situations for the device and the user alike, which could cause malfunction or data loss. |
Operation with ONT
Примечание |
---|
Matches between parameter names and digital OIDs are described in the MIB files. |
...
If the ONT configuration does not allow a profile to be specified, the number 0 is sent instead of the profile index to set such a value.
Configuration
ONT is configured by the following tables:
- ltp16nONTConfigTable — general parameters;
- ltp16nONTServiceTable — Cross-Connect and DBA profiles.
Addition
The following indexes are used in ONT configuration tables: <gpon_port>, <ont_id>.
...
This command creates ONT 3/8 with serial number ELTX24A80012.
Editing
ONT General Parameters
General parameters of ONT are configured by using ltp16nONTConfigTable.
...
This command sets password=1234567890, assigns the Ports profile with index 1, assigns the Management profile with index 1 and disables the Broadcast filter for ONT 3/8.
Cross-Connect and DBA profiles
Cross-Connect and DBA profiles are configured by using ltp16nONTServiceTable. An additional index is specified — the service number.
...
This command sets Cross-Connect profile with index 1, and DBA profile with index 2 for service 7 for ONT 3/8.
ONT Deletion
Command format:
snmpset -v2c -c <rw_community> <ipaddr>
ltp16nONTConfigRowStatus.1.<gpon_port>.<ont_id> i 6
...
This command removes the ONT 3/8 configuration.
ONT replacement
You can change ONT by using subsequent commands for deleting and creating configurations with new parameters.
Reconfiguration
Command format:
snmpset -v2c -c <rw_community> <ipaddr>
ltp16nONTOperationsReconfigure.1.<gpon_port>.<ont_id> i 1
...
Блок кода | ||
---|---|---|
| ||
snmpset -v2c -c private 192.168.1.2 ltp16nONTOperationsReconfigure.1.3.8 i 1 |
Scroll Pagebreak |
---|
Reboot
Command format:
snmpset -v2c -c <rw_community> <ipaddr>
ltp16nONTOperationsReboot.1.<gpon_port>.<ont_id> i 1
...
Блок кода | ||
---|---|---|
| ||
snmpset -v2c -c private 192.168.1.2 ltp16nONTOperationsReboot.1.3.8 i 1 |
Reset to the default settings
Command format:
snmpset -v2c -c <rw_community> <ipaddr>
ltp16nONTOperationsDefault.1.<gpon_port>.<ont_id> i 1
...
Блок кода | ||
---|---|---|
| ||
snmpset -v2c -c private 192.168.1.2 ltp16nONTOperationsDefault.1.3.8 i 1 |
Requests
Common ONT state
The parameters of ONT state can be requested by using ltp16nONTInfoTable.
...
The command reauests the status and RSSI for the ONT 3/8.
OLT configuration:
Applying and saving configuration
Configuration actions are performed using ltp16nConfigOperations.
Configuration commit
To write the configuration to running-config, execute Commit.
...
Блок кода | ||
---|---|---|
| ||
snmpset -v2c -c private -t 20 192.168.1.2 ltp16nConfigOperationsCommit.0 i 1 |
Saving the configuration to non-volatile memory
To write the configuration to the non-volatile memory, execute Save.
...
Блок кода | ||
---|---|---|
| ||
snmpset -v2c -c private -t 20 192.168.1.2 ltp16nConfigOperationsSave.0 i 1 |
VLAN Configuration
VLAN configuration is done using the tables:
- ltp16nVLANSettingsTable — general VLAN parameters;
- ltp16nVLANSettingsIGMPTable — IGMP parameters;
- ltp16nVLANSettingsIGMPSnoopingTable — IGMP Snooping parameters;
- ltp16nVLANSettingsIGMPSnoopingStaticGroupTable — static group management.
Adding VLAN
Command format:
snmpset -v2c -c <rw_community> <ipaddr> ltp16nVLANSettingsRowStatus.1.<vlan_id> i 4
...
Якорь Редактирование VLAN Редактирование VLAN
VLAN editing
It is possible to change the name and IGMP settings for any VLAN via SNMP.
...
The command sets VLAN 156 to be named «edited_by_snmp», enables IGMP snooping and IGMP snooping querier, sets IGMPQueryInterval=300, adds a static multicast group 225.25.32.185 for interface gpon-port 5.
VLAN Deletion
Command format:
snmpset -v2c -c <rw_community> <ipaddr> ltp16nVLANSettingsRowStatus.1.<vlan_id> i 6
...
The command deletes VLAN 156 from the configuration.
Requesting the VLAN list and configuration of the specific VLAN
To request VLAN list, use the following request:
...
The command outputs the VLAN 156 configuration.
IGMP configuration
Global settings for enabling IGMP Snooping
To configure IGMP, use ltp16nIGMPSnoopingTable. OIDs for configuring global parameters are listed in the table below:
...
The command enables IGMP Snooping.
IGMP Snooping and VLAN Querier configuration
This setting is carried out similarly to the «VLAN Editing» section
Scroll Pagebreak |
---|
ONT profiles configuration
Cross-connect
For operation with cross-connect profile, use ltp16nONTProfileCrossConnectTable.
Addition
Command format:
snmpset -v2c -c <rw_community> <ipaddr>
ltp16nONTProfileCrossConnectRowStatus.<profile_index> i 4
...
The command adds Cross-connect profile with index 2.
Editing
Command format:
snmpset -v2c -c <rw_community> <ipaddr>
...
The command sets the name «edited_by_snmp», traffic-model multicast, ont mode = bridge, bridge group = 5 and Outer VID 156 for the Cross-connect profile with index 2.
Scroll Pagebreak |
---|
Deletion
Command format:
snmpset -v2c -c <rw_community> <ipaddr>
ltp16nONTProfileCrossConnectRowStatus.<profile_index> i 6
...
The command deletes Cross-connect profile with index 2.
Profile list request
Command format:
snmpwalk -v2c -c <ro_community> <ipaddr> ltp16nONTProfileCrossConnectName
...
Блок кода | ||
---|---|---|
| ||
snmpwalk -v2c -c public 192.168.1.2 ltp16nONTProfileCrossConnectName |
DBA
For operation with DBA profiles, use ltp16nONTProfileDBATable.
Addition
Command format:
snmpset -v2c -c <rw_community> <ipaddr>
ltp16nONTProfileDBARowStatus.<profile_index> i 4
...
The command adds DBA profile with index 3.
Scroll Pagebreak |
---|
Editing
Command format:
snmpset -v2c -c <rw_community> <ipaddr>
...
The command sets the name «edited_by_snmp», status-reporting mode and besteffort bandwidth 3 for the DBA profile with index 3.
Deletion
Command format:
snmpset -v2c -c <rw_community> <ipaddr>
ltp16nONTProfileDBARowStatus.<profile_index> i 6
...
The command deletes DBA profile with index 3.
Profile list request
Command format:
snmpwalk -v2c -c <ro_community> <ipaddr> ltp16nONTProfileDBAName
...
Блок кода | ||
---|---|---|
| ||
snmpwalk -v2c -c public 192.168.1.2 ltp16nONTProfileDBAName |
Scroll Pagebreak
Ports
For operation with Ports profile, use the following tables:
- ltp16nONTProfilePortsTable — general profile parameters;
- ltp16nONTProfilePortsUNIPortTable — UNI ports.
Addition
Command format:
snmpset -v2c -c <rw_community> <ipaddr>
ltp16nONTProfilePortsRowStatus.<profile_index> i 4
...
The command adds Ports profile with index 4.
Editing
General parameters:
Command format:
...
The command sets bridge group = 100, enables multicast, priority for igmp upstream traffic 0, vid 20 for igmp upstream traffic and substitutes a label for igmp upstream traffic for profile Ports with index 4, for port with index 1.
Deletion
Command format:
snmpset -v2c -c <rw_community> <ipaddr>
ltp16nONTProfilePortsRowStatus.<profile_index> i 6
...
The command deletes Ports profile with index 4.
Profile list request
Command format:
snmpwalk -v2c -c <ro_community> <ipaddr> ltp16nONTProfilePortsName
...
Блок кода | ||
---|---|---|
| ||
snmpwalk -v2c -c public 192.168.1.2 ltp16nONTProfilePortsName |
Management
For operation with Management profiles, use ltp16nONTProfileManagementTable.
Addition
Command format:
snmpset -v2c -c <rw_community> <ipaddr>
ltp16nONTProfileManagementRowStatus.<profile_index> i 4
...
The command adds Management profile with index 10.
Editing
General parameters:
Command format:
...
The command sets name "testProfile", iphost ID 10, disables configuration via OMCI, sets management server URL "http://192.168.1.5", management server username "acs1", password "acsacs1" for the Management profile with index 10.
Deletion
Command format:
snmpset -v2c -c <rw_community> <ipaddr>
ltp16nONTProfileManagementRowStatus.<profile_index> i 6
...
The command removes Management profile with index 10.
Profile list request
Command format:
snmpwalk -v2c -c <ro_community> <ipaddr> ltp16nONTProfileManagementName
...
Блок кода | ||
---|---|---|
| ||
snmpwalk -v2c -c public 192.168.1.2 ltp16nONTProfileManagementName |
Interface configuration
GPON-ports
The configuration of the interface gpon-ports is performed using ltp16nGponPortConfigTable.
...
The command disables interface gpon-port 1 in the configuration.
Front-ports
The configuration of the interface front-ports is performed using ltp16nFrontPortConfigTable, ltp16nFrontPortConfigAllowedVLANTable .
...
The command removes VLAN 156 for interface 10G-front-port 5.
OLT monitoring
LTP general information
General information about LTP is collected in the ltp16nSystem and ltp16nBoardStatus. groups.
...
The command displays the LTP MAC address, the current Fan1 fan speed and the amount of free memory in Mb.
The list of changes
Document version | Issue date | Firmware version | Revisions |
---|---|---|---|
Version 1.1 | 28.05.2021 | 1.2.0 | Synchronization with firmware version 1.2.0 Sections added:
|
Version 1.0 | 30.12.2020 | 1.1.0 | First issue |
...