...

Introduction

Annotation

This manual describes the ACS mode CLI commands for the LTP-4X rev.B, LTP-8X rev.B, LTP-4X rev.C, LTP-8X rev.C, LTP-4X rev.D, LTP-8X rev.D (further LTP-X) administrator.
Command Line Interface (CLI) allows to perform the device management and monitor its operation and status. You will require the PC application supporting Telnet protocol operation or direct connection via the console port (e.g. HyperTerminal).

Target audience

The CLI command guide is designed for technicians who install, configure, monitor and maintain LTP-X devices via the CLI configurator. Qualified technical personnel should be familiar with the operation basics of ТСР/IP & UDP/IP protocol stacks and Ethernet and GPON networks design concepts.

Symbols

Notes and warnings

...

ACS description

TR-069 is a technical specification that defines the Internet protocol for management of network equipment — CWMP (CPE WAN Management Protocol). The standard was published in 2004 by the DSL Forum consortium, later renamed Broadband Forum. The goal is to standardize and unify the principles and approaches to subscriber equipment management from different manufacturers.

...

Switching to the ACS configuration mode is performed from the root menu with the acs command.

The figure 1 shows the interrelation of command modes that are accessed from the ACS mode.

...

Firmware. Firmware parameters configuration mode

Adding a firmware update profile

Description: This command adds a new firmware update profile.

...

Meaning: Firmware update profile with index 1 has been successfully added.

Adding a new equipment model

Description: This command adds a new equipment model to the specific firmware update profile.

...

Assigning equipment configuration profile to firmware update profile

Meaning: This command assigns configuration profile for the specific firmware update pprofile.

...

Meaning: The "NTU-2V" configuration profile is assigned to the firmware update profile with index 2.

ONT firmware file downloading

Description: This command copies the firmware file from the TFTP server to the internal LTP memory.

...

Meaning: The command to copy the firmware file ntu-rg-1402-3.24.0.1588.bin from the TFTP server 192.168.5.100 to the internal LTP memory is provided.

Settings deletion

Deleting all firmware files

Description: This command deletes all ONT firmware files uploaded to the device.

...

Parameters: there are no parameters for this command.

Deleting a specified firmware file

Description: This command deletes the firmware file by its name.

...

<Filename> — file name, 250 characters max.

Deleting a firmware update profile

Description: This command deletes the firmware update profile .

...

<Firmware ID> — firmware update profile identifier, values in the range from 1 to 32.

Deleting a device model from firmware update profile

Description: This command deletes the device model from the list of the specific firmware update profile.

...

<Firmware ID> — firmware update profile identifier, values in the range from 1 to 32;
<Hardware name> — model name.

Deleting update configuration profiles from firmware update profile

Description: This command deletes ONT configuration profile from the firmware update profile.

...

Meaning: The "NTU-2V" configuration profile is deleted from the firmware update profile with index 1.

Switching to firmware update profile configuration

Description: This command transitions to the configuration of the selected profile.

...

<Firmware ID> — firmware update profile identifier, values in the range from 1 to 32.

Adding a new device model (ONT)

Command syntax: add hardware <Hardware name>

...

Command syntax: add profile <Profile name>

Adding configuration profiles

Parameters:

<Profile name> — configuration profile name, 250 characters max.

Deleting the device model (ONT)

Command syntax: delete hardware <Hardware name>

...

<Hardware name> — hardware model name, 250 characters max.

Deleting configuration profiles 

Command syntax: delete profile <Profile name>

...

<Profile name> — configuration profile name, 250 characters max.

Setting a firmware file for the firmware update profile

Command syntax: set file <Filename>

...

<Filename> — firmware file name, 250 characters max.

Setting a firmware file (by name) for the firmware update profile

Command syntax: set filename <Filename>

...

Enable firmware update schedule operation

Command syntax: set schedule <Schedule mode>

...

• Enabled — ONT firmware will be updated on schedule;
• Disabled — firmware update will not be performed.

Specify external HTTP server URL

Command syntax: set url <URL>

...

<URL> — external HTTP server URL, 250 characters max.

Assign firmware version to file specified in this profile

Command syntax: set version <Version>

...

<version> — firmware version, 250 characters max.

Display full information on specific profile

Command syntax: show config

Parameters: there are no parameters for this command.

Display list of models, that the current profile will be applied to

Command syntax: show hardware

Parameters: there are no parameters for this command.

List the assigned configuration profiles for the firmware update profile

Command syntax: show profile

Parameters: there are no parameters for this command.

Go to firmware update schedule configuration

Description: This command transitions to the configuration of the update schedule.

...

Adjust daily schedule

Description: This command allows to set/adjust the daily schedule.

...

Meaning: Daily schedule is assigned — active from 9:00 to 19:00.

Adjust activity period

Description: This command allows to set/adjust the periodic schedule.

...

Meaning: Schedule is assigned — active from 1 September 2011 to 1 March 2012.

Adjust weekly schedule

Description: This command allows to set/adjust the weekly schedule.

...

Meaning: Weekly schedule is assigned — active from Monday to Friday.

Define default schedule settings

Description: This command defines daily/weekly/periodic schedule settings.

...

1: daily 00:00 23:59
2: period 2011-06-01 2099-12-31
3: weekly 1 7

Show firmware update schedule settings

Description: This command shows assigned ACS schedules.

...

Parameters: there are no parameters for this command.

Configuration of the list of displayed parameters for the command show list

Description: This command allows you to select fields to be displayed, while viewing the configuration.

...

<Field num> — field number, field numbers correspond to the following parameters:
1 — hardware identifier;
2 — firmware version;
3 — URL;
4 — firmware file name;
5 — security mode;
6 — version downgrade;
5 — schedule;
6 — hardware (equipment);
7 — profiles;
[Mode] — field display mode:
On — field is displayed (default value);
Off — field is not displayed;
[Length] — field length, from 1 to 250 characters:
0 is default.

View update configuration

View file list

Description: This command is used to view the list of ONT firmware files on the LTP-8X file system.

...

Parameters: there are no parameters for this command.

View firmware update profile configuration

Description: This command is used to view full information about the firmware update profile.

...

<Firmware ID> — firmware update profile identifier, values in the range from 1 to 32.

Scroll Pagebreak

View the list of device models assigned to this firmware update profile

Description: This command is used to view the list of equipment, for which the specified profile is intended.

...

<Firmware ID> — firmware update profile identifier, values in the range from 1 to 32.

View the list of firmware update profiles

Description: This command is used to view the full list of firmware update profiles and their configuration.

...

Parameters: there are no parameters for this command.

View configuration profiles assigned to a specified firmware update profile

Description: This command is used to view the list of assigned configuration profiles for this firmware update profile. 

...

Meaning: One configuration profile is assigned to the firmware update profile with index 2.

Viewing information display parameters of the command show list

Description: This command is used to view the list of fields to be displayed and their size when executing the command show list.

...

(acs-firmware)show mode 
Firmware show mode:
1: Firmware ID - on [11]
2: Version - on [20]
3: URL - off [30]
4: Filename - on [40]
5: Schedule - on [10]
6: Safe-mode - on [10]
7: Downgrade - on [10]
8: Hardware - on [20]
9: Profiles - on [20]

Hardware — hardware parameters configuration mode.

...

Adding a new equipment model

Description: This command adds a new equipment model.

...

<Name> — equipment name, no more than 250 characters.

Deleting equipment

Description: This command deletes an equipment model.

...

<Name> — equipment name, no more than 250 characters.

Switching to equipment parameters configuration

Description: This command transitions to the mode of editing parameters of the equipment model.

...

(acs-hardware-name='NTP-RG-1402G')

Equipment parameters configuration: assignment of class

Command: set class

Command syntax: set class <Product class>

...

Meaning: The product class «NTP-RG-1402G» is assigned to the NTP-RG-1402G equipment model. 

Equipment parameters configuration: manufacturer 

Command: set manufacturer

Command syntax: set manufacturer <Manufacturer OUI>

...

Meaning: Manufacturer "Eltex" has been assigned for the equipment model NTP-RG-1402G.

Equipment parameters configuration: hardware version

Command: set version

Command syntax: set version <Hardware version>

...

Meaning: Hardware version 1v3 has been assigned for the equipment model NTP-RG-1402G.

Equipment parameters configuration: default profile

Command: set profile

Command syntax: set profile <profile name>

...

Meaning: For the NTP-RG-1402G equipment model, the default profile new_ont is assigned.

View hardware information

Command: show config

Command syntax: show config

...

Information about hardware:
ID = 2
Display name = "NTP-RG-1402G"
Manufacturer OUI = "A8F94B"
Product class = "NTP-RG-1402G"
Manufacturer = "Eltex"
Hardware version = "1v3"

Parameter display mode configuration

Description: This command allows to select fields to be displayed, while viewing the hardware configuration.

...

<Field num> — field number, field numbers correspond to the following parameters:
1 — hardware identifier;
2 — displayed hardware name;
3 — unique manufacturer identifier;
4 — product class;
5 — manufacturer;
6 — hardware version;
[Mode] — field display mode:
On — field is displayed (default value);
Off — field is not displayed;
[Length] — field length, from 1 to 250 characters:
0 — length is not specified.

View hardware configuration

View hardware information

Description: This command is used to view full information about the selected equipment model.

...

Information about hardware:
ID = 1
Display name = "NTU-2V"
Manufacturer OUI = "A8F94B"
Product class = "NTU-2V"
Manufacturer = "Eltex"
Hardware version = "2v2"

Scroll Pagebreak

View the list of equipment models

Description: This command is used to view the list of equipment models.

...

ID Display name Manufacturer OUI Product class Manufacturer Hardware version
1: 1 NTP-2 A8F94B NTP-2 Eltex 1v2
2: 2 NTP-RG-1402G A8F94B NTP-RG-1402G Eltex 1v3
3: 3 NTP-RG-1402G-W A8F94B NTP-RG-1402G-W Eltex 1v3
4: 4 NTP-RG-1400G A8F94B NTP-RG-1400G
5: 5 NTP-RG-1400G-W A8F94B NTP-RG-1400G-W
6: 6 NTP-RG-1400G-W2 A8F94B NTP-RG-1400G-W2
7: 7 NTP-RG-1402G-W2 A8F94B NTP-RG-1402G-W2
8: 8 NTP-RG-1400GC A8F94B NTP-RG-1400GC
9: 9 NTP-RG-1400GC-W A8F94B NTP-RG-1400GC-W
10: 10 NTP-RG-1400GC.. A8F94B NTP-RG-1400GC..
11: 11 NTP-RG-1402GC A8F94B NTP-RG-1402GC
12: 12 NTP-RG-1402GC-W A8F94B NTP-RG-1402GC-W
13: 13 NTP-RG-1402GC.. A8F94B NTP-RG-1402GC..
14: 14 NTP-RG-1402GB A8F94B NTP-RG-1402GB
15: 15 NTP-RG-1402GB-W A8F94B NTP-RG-1402GB-W
16: 16 NTP-RG-1402GB.. A8F94B NTP-RG-1402GB..
17: 17 NTP-RG-1402GCB A8F94B NTP-RG-1402GCB
18: 18 NTP-RG-1402GC.. A8F94B NTP-RG-1402GC..
19: 19 NTP-RG-1402GC.. A8F94B NTP-RG-1402GC..
20: 20 96816GWV A8F94B 96816GWV
21: 21 96816PVWM A8F94B 96816PVWM
22: 22 96812PG A8F94B 96812PG
23: 23 NTP-2C A8F94B NTP-2C

View the configuration of the command to display the list of configured equipment models: show list

Description: This command is used to view the status of the fields when displaying configuration parameters show list. 

...

Hardware model show mode:
1: ID - on [10]
2: Display name - on [15]
3: Manufacturer OUI - on [20]
4: Product class - on [15]
5: Manufacturer - on [15]
6: Hardware version - on [16]

Informs — ACS information message settings

Message deletion

Description: This command allows to delete Inform ACS messages during the specified period or delete all messages.

...

[from= Date from] start date in the YYYY-MM-DD format;
[to= Date to] end date in the YYYY-MM-DD format.

Parameter display mode configuration

Description: This command allows to select fields to be displayed, while viewing the information using the show list command.

...

<fld num> — field number, field numbers correspond to the following parameters:
1 — message identifier;
2 — device serial number;
3 — event on the device;
4 — current date and time;
5 — manufacturer;
6 — manufacturer identifier;
7 — device model;
8 — MaxEnvelopes ;
9 — restart counter;
10 — general information on device;
11 — specification version;
12 — hardware version;
13 — firmware version;
14 — initialization version;
15 — connection request link;
16 — device state;
17 — interface;
18 — device IP address;
[mode] — field display mode:
On — field is displayed (default value);
Off — field is not displayed;
[Length] — field length, from 1 to 250 characters.

View parameters

View the Informs log for the specified device

Description: This command allows to view the list of information messages related only to the specified device.

...

Meaning: Displays the list of information messages for ONT number 454C54581A010F91.

View Inform message information

Description: This command allows to view the full information about the information message with the specified identifier.

...

Meaning: Detailed information about message with identifier 41 is displayed.

View Informs log

Description: This command is used to view the list of inform messages.

...

[from= Date from] start date in the YYYY-MM-DD format;
[to= Date to] end date in the YYYY-MM-DD format.

View the parameter display mode

Command: show mode

Command syntax: show mode 

...

Informs show mode:
	1: ID - on [6]
	2: SerialNumber - on [13]
	3: Events - on [20]
	4: CurrentTime - on [20]
	5: Manufacturer - off [10]
	6: OUI - off [10]
	7: ProductClass - off [20]
	8: MaxEnvelopes - off [2]
	9: RetryCount - off [3]
	10: DeviceSummary - off [30]
	11: SpecVersion - off [11]
	12: HardwareVersion - off [15]
	13: SoftwareVersion - on [15]
	14: ProvisioningCode - off [16]
	15: ConnectionRequestURL - off [20]
	16: ParameterKey - off [20]
	17: Interface - off [30]
	18: IPAddress - on [15]

Ont — ONT parameters configuration mode

Settings addition

Adding ONT to configuration

Description: This command adds ONT to the configuration.

...

Adding parameters to ONT configuration

Description: This command is used to add new parameters to the ONT configuration.

...

add property eltx08000001 "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.1.Username""1"

Adding service for ONT

Description: This command is used to add a new service for ONT.

...

(acs-ont)add service 454C54581A010F91 22

Execution result: Ok

Configuration reset

Reset ONT parameters

Description: This command deletes all existing ONT parameters.

...

Meaning: For ONT with serial number 454C54581A010F91, all existing parameters have been removed.

Reset ONT services

Description: This command deletes all existing ONT services.

...

Meaning: For ONT with serial number 454C54581A010F91, all existing services have been removed.

Settings deletion

ONT Deletion

Description: This command deletes the specified ONT service.

...

Meaning: ONT with serial number 454C54581A010F91 has been removed from configuration.

Deleting ONT parameters

Description: This command deletes the specified ONT parameter.

...

<serial> ONT serial number, 64 characters max.;
<Prop name> parameter name.

Deleting ONT services

Description: This command deletes the specified ONT service.

...

<serial> — ONT serial number, 64 characters max.;
<service name> service name;
[instance] — mapping parameter, may take values in the range from 0..100, the default is 1.

Switch to ONT parameters configuration 

Description: This command moves on to configuring the ONT parameters.
Command: ont

...

(acs-ont-sn='454C54581A010F91')

ONT parameters configuration: adding parameters

Command: add property

Command syntax: add property <Prop name> <Value> [Check mode] 

...

• Nocheck — do not perform the conformance check;
• Check — perform the conformance check (default value).

ONT parameters configuration: adding services

Command: add service

Command syntax: add service <Service name> [Instance] 

...

<service name> — service name;
[instance] — mapping parameter, may take values in the range from 0..100, the default is 1.

Scroll Pagebreak

ONT parameters configuration: deleting all parameters

Command: clear property

Command syntax: clear property

Parameters: there are no parameters for this command.

ONT parameters configuration: deleting all services

Command: clear service

Command syntax: clear service

Parameters: there are no parameters for this command.

ONT parameters configuration: deleting specified parameters

Command: delete property

Command syntax: delete property <Prop name>

...

<Prop name> — parameter name, 250 characters max.

ONT parameters configuration: deleting specified services

Command: delete service

Command syntax: delete service <Service name> [Instance] 

...

<service name> — service name, 250 characters max.;
[instance] — mapping parameter, may take values in the range of 0..100, the default is 1.

ONT management: reboot ONT

Command: reboot

Command syntax: reboot

Parameters: there are no parameters for this command.

ONT management: reconfiguration

Command: reconfigure

Command syntax: reconfigure

Parameters: there are no parameters for this command.

ONT parameters configuration: assigning the configuration name

Command: set config

Command syntax: set config <Config name>

...

<Config name> — configuration name, 250 characters max.

Scroll Pagebreak

ONT parameters configuration: assigning the customer identifier

Command: set customer

Command syntax: set customer <Customer ID>

...

<Customer ID> — customer identifier, 250 characters max.

ONT parameters configuration: device model configuration

Command: set hardware

Command syntax: set hardware <Hardware name>

...

ONT parameters configuration: access password configuration

Command: set password

Command syntax: set password <Password>

...

<Password> — device access password, 250 characters max.

ONT parameters configuration: assigning the configuration profile

Command: set profile

Command syntax: set profile <profile name>

...

<Profile name> — profile name, 250 characters max.

ONT parameters configuration: assigning the configuration parameters

Command: set property

Command syntax: set property <Prop name> <Value> [Check mode]

...

• Nocheck — do not perform the conformance check;
• Check — perform the conformance check (default value).

Scroll Pagebreak

ONT parameters configuration: assigning the user name

Command: set username

Command syntax: set username <Username>

...

<Username> — user name, 250 characters max.

ONT management: reset to the default settings

Command: setfactdef

Command syntax: setfactdef

Parameters: there are no parameters for this command.

ONT parameters configuration: view the configuration

Command: show config

Command syntax: show config

...

(acs-ont-sn='454C54581A010F91')show config
Information about ONT '454C54581A010F91':
ID = 66
Serial = "454C54581A010F91"
Profile = "cycleupd"
Hardware name = "NTP-RG-1402G-W:rev.C"
Firmware = "3.22.0.2452"
URL = "http://192.168.200.155:30005/"
Config name = "Default"
Sfw upd time = "2000-01-01 00:35:30"
Sfw upd res = ""
Cfg upd res = ""
Last contact = "2015-08-11 19:31:15"
Cfg upd time = "1901-12-14 03:45:52"
Hardware = "1v10"
Cfg version = ""
Username = ""
Password = ""
Authtype = 0
Customer ID = ""
Con req user = "admin"
Con req pass = "admin"
Cfg force = 0
Subscriber = ""
(acs-ont-sn='454C54581A010F91')

Scroll Pagebreak

ONT parameters configuration: view the list of configuration parameters assigned to the ONT

Command: show property

Command syntax: show property

Parameters: there are no parameters for this command.

ONT parameters configuration: view the list of assigned services

Command: show service

Command syntax: show service

Parameters: there are no parameters for this command.

ONT parameters configuration: view the full ONT configuration

Command: show full

Command syntax: show full

Parameters: there are no parameters for this command.

Parameter display mode configuration

Description: This command allows to select fields to be displayed, while viewing the list using the ONT show list command.

...

1 — device identifier;
2 — ONT serial number;
3 — ONT profile name;
4 — hardware name (device model);
5 — firmware version;
6 — address;
7 — configuration name;
8 — date and time of the last firmware update;
9 — firmware update status;
10 — configuration update status;
11 — date of the last connection to the device;
12 — date and time of the last configuration update;
13 — hardware version;
14 — configuration version;
15 — user name;
16 — password;
17 — authorization type;
18 — user identifier;
19 — connection request counter (user name);
20 — connection request counter (password);
21 — configuration interventions;
22 — subscriber;
[Mode] — field display mode:
On — field is displayed (default value);
Off — field is not displayed;
[Length] — field length, from 1 to 250 characters.

ONT parameters configuration

Description: This command adjusts the ONT configuration parameter (adding a new one or changing an existing one).

...

• Nocheck — do not perform the conformance check;
• Check — perform the conformance check (default value).

View ONT parameters

View full information on ONT

Description: This command is used to view full information about ONT.

...

<Serial> — ONT serial number, 64 characters max.

View list of configured ONTs

Description: This command is used to view the list of configured ONTs.

...

180: 454C54585C00960C 0: Default NTU-RG-1402G-W 3.22.0.1568 2015-08-06 05:09:11 
181: 454C54585D000090 0: Default NTU-RG-1402G-Wac 3.22.0.1471 2015-07-29 03:22:26 
182: 454C54585C00007C 0: Default NTU-RG-1402G-W 3.22.0.1568 2015-08-06 05:02:38 
183: 454C54585C009620 0: Default NTU-RG-1402G-W 3.22.0.1568 2015-08-06 05:02:29 
184: 454C54585C000FC0 0: Default NTU-RG-1402G-W 3.22.0.1568 2015-08-06 05:02:19 
185: 454C54585C009684 0: Default NTU-RG-1402G-W 3.22.0.1568 2015-08-06 05:03:18 
186: 454C54585D000040 0: Default NTU-RG-1402G-Wac 3.22.0.1471 2015-07-29 03:22:41 
187: 454C54585D0000E4 0: Default NTU-RG-1402G-Wac 3.22.0.1471 2015-07-29 03:22:46 
188: 454C54585C000FA4 0: Default NTU-RG-1402G-W 3.22.0.1568 2015-08-06 05:02:42

View list of connected ONTs with filter

Description: This command is used to view the list of connected ONTs filtered by the specified value.

...

Meaning: ONT output with the specified hardware type is presented.

View an ordered list of connected ONTs

Description: This command is used to view the list of connected ONTs ranged by the specified parameter.

...

Meaning: A list of connected ONTs is displayed, ordered by the date of the last connection to the device.

View the information about the fields to be displayed when executing the show list command

Description: This command is used to view the status of fields when displaying the ONT list, by show list command.

...

Parameters: there are no parameters for this command.

Scroll Pagebreak

View information on ONT parameters

Description: This command is used to view information about ONT.

...

(acs-ont)show ont 454C54581A002AA1
Information about ONT '454C54581A002AA1':
ID = 55
Serial = "454C54581A002AA1"
Profile = "cycleupd"
Hardware name = "NTP-RG-1402G-W:rev.C"
Firmware = "3.22.0.2452"
URL = "http://192.168.200.113:30005/"
Config name = "Default"
Sfw upd time = "2000-01-01 00:35:19"
Sfw upd res = ""
Cfg upd res = ""
Last contact = "2015-08-11 19:46:05"
Cfg upd time = "1901-12-14 03:45:52"
Hardware = "1v8"
Cfg version = ""
Username = ""
Password = ""
Authtype = 0
Customer ID = ""
Con req user = "admin"
Con req pass = "admin"
Cfg force = 0
Subscriber = ""
(acs-ont)

View the list of ONT parameters

Description: This command is used to view the list of ONT parameters.

...

<Serial> — ONT serial number, 64 characters max.

View the list of ONT services

Description: This command is used to view the list of services assigned to the ONT.

...

<Serial> — ONT serial number, 64 characters max. 

Viewing a specific subscriber's configuration

Description: This command is used to view information about subscribers.

...

Meaning: The configuration information for the petrov user is displayed.

Privates — personal configuration mode

Adding the personal parameter

Description: This command adds the correspondence between the personal parameter and the personal rule.

...

LTP-X(acs-privates)add ip InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.ExternalIPAddress

Ok

Deleting a rule by number

Description: This command deletes the rule of the specified parameter by its sequential number.

...

LTP-X(acs-privates)# delete index ip 1

Ok

Deleting a rule by name

Description: This command deletes the firmware file by its name.

...

LTP-X(acs-privates)# delete name InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.ExternalIPAddress

Ok

Deleting a personal parameter by name

Description: This command deletes a personal parameter. 

...

LTP-X(acs-privates)# delete param ip

View the information about personal parameters

Description: This command allows to view a list of personal parameters and rules that match them.

...

LTP-X(acs-privates)# show param voice1_enable
List of privates for user property 'voice1_enable':
1. InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1.Enable

Profiles — configuration profile configuration mode

Settings addition

Adding a configuration profile

Description: This command adds a new profile for the device.

...

<Name> — profile name, 250 characters max.;
[Base profile] — base profile name.

Adding parameters to the configuration profile

Description: This command adds new parameters to the profile.

...

• Nocheck — do not perform the conformance check;
• Check — perform the conformance check (default value).

Deleting all parameters from profile  

Description: This command deletes all parameters from the specified profile.

...

<Name> — profile name, 250 characters max.

Settings deletion

Deleting configuration profile

Description: This command deletes the profile.

...

<Name> — profile name, 250 characters max.

Scroll Pagebreak

Deleting parameters from the specified profile

Description: This command deletes the profile parameters.

...

<Name> — profile name, 250 characters max.;
<Prop name> — profile parameter name, 250 characters max.

Configure parameter output mode using show list command

Description: This command allows to select fields to be displayed, while viewing the configuration profiles list.

...

<Field num> — field number, field numbers correspond to the following parameters:
1 — profile name;
2 — Inform interval (ONT and ACS exchange period);
3 — script name;
4 — base profile;
5 — Description;
[Mode] — field display mode:
On — field is displayed (default value);
Off — field is not displayed;
[Length] — field length, from 1 to 250 characters.

Modify/add configuration profile settings

Description: This command is used to modify/add device profile settings.

...

(acs-profile)set property NTP-2 "InternetGatewayDevice.X_BROADCOM_COM_IGMPCfg.AvailableGroupsEntity.1.DestinationIPStart""233.7.70.1"

Scroll Pagebreak

View settings

View profile list

Description: This command is used to view the list of configuration profiles.

...

(acs-profile)show list
Listing of device profiles:
Name Inform interval Script name Base profile
1: 0 3600
2: cycleupd 3600
3: internet_iptv_voip 600
4: internet_iptv 3600
5: ntu-2v 3600
(acs-profile)

View the information about fields to be displayed

Description: This command is used to view the status of the fields when displaying ONT parameters.

...

Device profile show mode:
1: Name - on [5]
2: Inform interval - on [15]
3: Script name - on [20]
4: Base profile - on [20]
5: Description - on [20]

View the list of ONT

Description: This command shows the list of ONTs, that the current profile is assigned to.

...

(acs-profile)show ont internet_iptv
List of hosts by profile 'internet_iptv':
Serial Profile Hardware name Firmware Last contact 
1: 454C54581A002E95 internet_iptv NTP-RG-1402G-W:rev.C 3.22.0.2452 2015-08-11 19:53:36
2: 454C54581A0021BD internet_iptv NTP-RG-1402G-W:rev.C 3.22.0.2452 2015-08-11 19:46:14
3: 454C54581A0021BC internet_iptv NTP-RG-1402G-W:rev.C 3.22.0.2452 2015-08-11 19:48:40
4: 454C54581A00F998 internet_iptv NTP-RG-1402G-W:rev.C 3.22.0.2393 2015-07-30 02:51:11
5: 454C54581A000041 internet_iptv NTP-RG-1402G-W:rev.C 3.22.0.2393 2015-07-30 02:47:34
6: 454C54581A00219F internet_iptv NTP-RG-1402G-W:rev.C 3.22.0.2452 2015-08-11 19:49:49
7: 454C54581A0021A5 internet_iptv NTP-RG-1402G-W:rev.C 3.22.0.2452 2015-08-11 19:51:23
8: 454C54581A002E93 internet_iptv NTP-RG-1402G-W:rev.C 3.22.0.2452 2015-08-11 19:48:18
9: 454C54581A002AE2 internet_iptv NTP-RG-1402G-W:rev.C 3.22.0.2452 2015-08-11 19:50:19
10: 454C54581A0021A0 internet_iptv NTP-RG-1402G-W:rev.C 3.22.0.2452 2015-08-11 19:51:59
11: 454C54581A00219C internet_iptv NTP-RG-1402G-W:rev.C 3.22.0.2452 2015-08-11 19:47:48
12: 454C54581A0021A7 internet_iptv NTP-RG-1402G-W:rev.C 3.22.0.2452 2015-08-11 19:51:26
Meaning: You will see the list of ONTs with assigned «internet_iptv» profile, that includes 12 devices.

View information on profile

Description: This command shows the full information on specific profile.

...

Parameters:

<Name> — profile name.

View profile settings list

Description: This command shows the profile settings list.

...

Parameters:

<Name> — profile name.

Scroll Pagebreak

View a hierarchically constructed list of profiles

Description: This command is used to view the ordered list of configuration profiles.

...

(acs-profile)show list
Listing of device profiles:
Name Inform interval Script name Base profile
0 : 0 3600 
1 : cycleupd 3600
2 : internet_iptv_voip 600
3 : internet_iptv 3600
4 : ntu-2v 3600
(acs-profile)

Switch to configuration profile parameter configuration

Description: This command allows to configure the configuration profile.

...

(acs-profile-name='NTU-2V')

Adding parameters to the configuration profile

Description: This command adds new parameters to the profile.

...

• Nocheck — do not perform the conformance check;
• Check — perform the conformance check (default value).

Scroll Pagebreak

Deleting all parameters from profile 

Description: This command deletes all parameters from the specified profile.

...

Command syntax: there are no parameters for this command.

Deleting parameters from the specified profile

Description: This command deletes parameters from the profile.

...

<Prop name> — profile parameters name, 250 characters max.

Assigning basic profile

Description: This command assigns the basic configuration profile.

...

<Base profile> — profile name, 250 characters max. 

Setting the profile description

Description: This command assigns a description to the profile.

...

<Description> — profile description, 250 characters max.

Setting the ONT exchange interval with ACS

Description: This command assigns the period of ONT exchange with ACS server.

...

<Inform interval> — exchange interval value 60..2147483647 in seconds.

Adding/changing parameters in the configuration profile

Description: This command adds new/changes parameters in the profile.

...

• Nocheck — do not perform the conformance check;
• Check — perform the conformance check (default value).

View information on profile

Description: This command shows the full information on specific profile.

...

Command syntax: there are no parameters for this command.

View the list of ONT

Description: This command shows the list of ONTs, that the current profile is assigned to.

...

Command syntax: there are no parameters for this command.

View profile settings list

Description: This command shows the profile settings list.

...

Command syntax: there are no parameters for this command.

Service — configuration mode of services for ONT

Settings addition

Adding the service

Description: This command adds a new service for the device.

...

<Name> — service name, 250 characters max.;
<Description> — service description, 250 characters max.

Adding parameters to the service

Description: This command adds new parameters to the service.

...

• Nocheck — do not perform the conformance check;
• Check — perform the conformance check (default value).

Deleting all parameters from service 

Description: This command deletes all parameters from the specified service.

...

<Name> — service name, 250 characters max.

Settings deletion

Deleting service

Description: This command deletes the service.

...

<Name> — service name, 250 characters max.

Deleting parameters from the specified service

Description: This command deletes the service parameters.

...

<Name> — service name, 250 characters max.;
<Prop name> — service parameter name, 250 characters max.

Configure parameter output mode using show list command

Description: This command allows to select fields to be displayed, while viewing the services list.

...

<Field num> — field number, field number correspond to the following parameters:
1 — Service identifier;
2 — Service name;
3 — Description;
4 — Mapping parameter;
[Mode] — field display mode:
On — field is displayed (default value);
Off — field is not displayed;
[Length] — field length, from 1 to 250 characters.

Change settings

Modify/add service settings

Description: This command is used to modify/add device service settings.

...

(acs-service)set property NTP-2 "InternetGatewayDevice.X_BROADCOM_COM_IGMPCfg.AvailableGroupsEntity.1.DestinationIPStart""233.7.70.1"

Modify/add service

Description: This command edits the selected service.

...

<Name> — service name, 250 characters max.;
<Description> — service description, 250 characters max.

Switch to service parameter configuration

Description: This command allows to configure the service.

...

(acs-service-name='ntp-rg')

Adding parameters to the service

Description: This command adds new parameters to the service.

...

• Nocheck — do not perform the conformance check;
• Check — perform the conformance check (default value).

Deleting all parameters from service

Description: This command deletes all parameters from the specified service.

...

Command syntax: there are no parameters for this command.

Scroll Pagebreak

Deleting parameters from the service

Description: This command deletes parameters from the service.

...

<Prop name> — service parameter name, 250 characters max.

Adding/changing parameters in the service

Description: This command adds new/changes parameters in the service.

...

• Nocheck — do not perform the conformance check
• Check — perform the conformance check (default value).

View information on service

Description: This command shows the full information on specific service.

...

Command syntax: there are no parameters for this command.

View service settings list

Description: This command shows the service settings list.

...

Command syntax: there are no parameters for this command.

View settings

View profile list

Description: This command is used to view the list of services.

...

Parameters: there are no parameters for this command.

Scroll Pagebreak

View the information about fields to be displayed

Description: This command is used to view the status of the fields when displaying service parameters.

...

Command syntax: there are no parameters for this command.

View service settings list

Description: This command shows the service settings list.

...

Parameters:

<Name> — service name.

View information on profile

Description: This command shows the full information on specific service.

...

Parameters:

<Name> — service name.

User — ACS information message settings

Adding the user

Description: This command adds the user to the ACS by his identifier.

...

Meaning: User test3 has been successfully added.

Deleting a user

Description: This command allows to view the full information about the information message with the specified identifier.

...

<Sub ID> — subscriber identifier, 250 characters max.

Parameter display mode configuration

Description: This command allows to select fields to be displayed.

...

<Field num> — field number, field numbers correspond to the following parameters:
1 — subscriber identifier;
2 — PON serial number;
3 — profile;
[Mode] — field display mode:
On — field is displayed (default value);
Off — field is not displayed;
[Length] — field length, from 1 to 250 characters.

Switch to editing individual subscriber characteristics

Description: This command is used to edit the characteristics of the specified user.

...

Meaning: Switch to editing the petrov user settings.

Specify/delete «Username for PPPoE authorization» parameter

Command: set/delete ppp_login

...

Meaning: The name «petrov» is set for the user petrov to authorize PPPoE.

Specify/delete «Password for PPPoE authorization» parameter

Command: set/delete ppp_password

...

Meaning: The password «n08fri5» is set for the user petrov to authorize PPPoE.

Set/delete «sip_proxy» parameter

Command: set sip_proxy

Command syntax: set sip_proxy <Value>

...

Meaning: The sip.proxy.ru SIP server is set on the device to use for registration For the petrov user.

Set/delete "voice_enable" parameter

Command: set/delete voice1(2)_enable

...

Meaning: The phone port 1 is activated on the device for the user.

Set/delete "voice_number" parameter

Command: set/delete voice1(2)_number

...

Meaning: The number 1 is set for user Petrov on port 1.

Set/delete «voice_password» parameter

Command: set/delete voice1(2)_password

...

Meaning: On port 1, user petrov has a password to access fd29zur4.

Scroll Pagebreak

Set the PON serial

Command: set pon_serial

Command syntax: set pon_serial <Serial> [Apply mode]

...

Meaning: A device with the serial number 454C54585D000064 is allocated to the petrov user.

Set the configuration profile for this user

Command: set profile

Command syntax: set profile <Profile>

...

<Profile> — profile name, 250 characters max.

Set/delete «wifi_enable» parameter

Command: set wifi_enable

Command syntax: set wifi_enable <status>

...

Meaning: The user has the Wi-Fi module enabled.

Set/delete «wifi_encoding» parameter

Command: set wifi_encoding

...

Meaning: WPA-2 encryption has been set for the petrov user.

Set/delete «wifi_password» parameter

Command: set wifi_password

...

Meaning: The petrov user has a password for the Wi-Fi network "poiuy38ghs".

Set/delete "wifi_ssid" parameter

Command: set wifi_ssid

Command: set wifi_ssid <SSID>

...

Meaning: The petrov user has the Wi-Fi network name "HomeNet".

Set/delete "admin_password" parameter

Command: set admin_password

...

Meaning: A password for the petrov user is set for the admin user on ONT "12345".

Scroll Pagebreak

View parameters

User list preview

Description: This command is used to view the list of subscribers.

...

Listing of subscribers:
Subscriber ID PON serial 
1: petrov 454C54585D000064
2: ivanov 454C54585D0000AC
3: sidorov 454C54585D0000B0

View settings

Description: This command allows to view the configured parameters for a subscriber.

...

Meaning: The parameters for the ivanov user are displayed.

View information on user

Description: This command allows to view full information about the specified user.

...

Meaning: Detailed information about the petrov user is displayed.

View the parameters display mode

Command: show mode

Command syntax: show mode 

...

Subscriber show mode:
1: Subscriber ID - on [20]
2: PON serial - on [20]
3: Profile - off [20]

The list of changes

...