show alarms active all
Display all active alarms.
Syntax
show alarms active all
Parameters
The command does not contain parameters.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms active all Active alarms (2): ## type severity description 1 fan critical fan slot 1 2 fan critical fan slot 2
show alarms active <FILTER>
Display all active alarms by filter.
Syntax
show alarms active <FILTER> <VALUE>
Parameters
<FILTER> - filters for alarms:
- type - filter alarms by type. <VALUE> values are available for this filter:
- fan - ventilation panel alarms;
- ram - memory lack alarm;
- load-average - CPU load alarm;
- temperature - temperature sensors alarm;
- pon-alarm-los - Loss of Signal pon alarm;
- pon-alarm-losi - Loss of Signal pon alarm for ONUi;
- pon-alarm-lofi - Loss of Frame pon alarm for ONUi;
- pon-alarm-loami - PLOAM Loss pon alarm for ONUi;
- pon-alarm-dowi - Drift of Window pon alarm for ONUi;
- pon-alarm-sdi - Signal Degraded pon alarm for ONUi;
- pon-alarm-sufi - Start-up Failure pon alarm for ONUi;
- pon-alarm-loai - Loss of Acknowledge pon alarm for ONUi;
- pon-alarm-dgi - Dying-Gasp pon alarm for ONUi;
- pon-alarm-dfi - Deactivate Failure pon alarm for ONUi;
- pon-alarm-tiwi - Transmission Interference Warning pon alarm for ONUi;
- pon-alarm-loki - Loss of Key pon alarm for ONUi;
- pon-alarm-lcdgi - Loss of GEM Channel Delineation pon alarm for ONUi;
- pon-alarm-rdii - Remote Defect Indication pon alarm for ONUi;
- login - system login alarm;
- login - system logout alarm;
- config-save - configuration save alarm;
- config-change - cofiguration change alarm;
- severity - filter alarms by importance. <VALUE> values are available for this filter:<VALUE> values are available for this filter:
- info;
- minor;
- major;
- critical
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms active type fan Active alarms (2): ## type severity description 1 fan critical fan slot 1 2 fan critical fan slot 2 LTP-16N# show alarms active severity info No alarms. LTP-16N# show alarms active severity critical Active alarms (2): ## type severity description 1 fan critical fan slot 1 2 fan critical fan slot 2
show candidate-config
Display the current candidate configuration. Displays a list of all nonapplied changes in a given session relative to the current configuration.
Syntax
show candidate-config
Parameters
The command does not contain parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config configure terminal management ip 192.168.1.3 exit commit exit
show candidate-config alarm
Displays the candidate configuration for alarms.
Syntax
show candidate-config alarm
Parameters
The command does not contain parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config alarm alarm system-temperature sensor gpon-ports-1 max 60 system-temperature sensor gpon-ports-2 max 60
show candidate-config interface 10G-front-port
Display the candidate configuration for 10G-front-port.
Syntax
show candidate-config interface 10G-front-port <PORT-ID>
Parameters
<PORT-ID> - port index in the range [1-8]. The parameter can be set by a range or enumeration (For example: interface 10G-front-port 1-5 or interface 10G-front-port 1,5).
Privilege group
view-configuration, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show candidate-config interface 10G-front-port 1 interface 10G-front-port 1 vlan allow 1000 exit
show candidate-config interface gpon-port
Display running configuration for gpon-port.
Syntax
show candidate-config interface gpon-port <PORT-ID>
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface gpon-port 1-3 ot interface gpon-port 1,3,5,7).
Privilege group
view-configuration, config-interface-gpon-port
Command mode
ROOT
Example
LTP-16N# show candidate-config interface gpon-port 15,16 interface gpon-port 15 shutdown exit interface gpon-port 16 shutdown exit
show candidate-config interface ont
Display the candidate configuration for ONT.
Syntax
show candidate-config interface ont <PORT-ID>[/ONT-ID]
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 ot interface ont 1,3,5,7).
[ONT-ID] - ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-configuration, config-interface-ont
Command mode
ROOT
Example
LTP-16N# show candidate-config interface ont 1/1 interface ont 1/1 service 1 profile cross-connect "HSI" dba "DBA" exit
show candidate-config ip dhcp
Display candidate configuration for DHCP.
Syntax
show candidate-config ip dhcp
Parameters
The command does not contain parameters
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config ip dhcp ip dhcp snooping enable exit
show candidate-config ip igmp
Display candidate configuration for IGMP.
Syntax
show candidate-config ip igmp
Parameters
The command does not contain parameters
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config ip igmp ip igmp snooping
show candidate-config ip pppoe
Display candidate configuration for PPPoE.
Syntax
show candidate-config ip pppoe
Parameters
The command does not contain parameters
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config ip pppoe ip pppoe snooping enable exit
show candidate-config ip snmp
Display candidate configuration for SNMP.
Syntax
show candidate-config ip snmp
Parameters
The command does not contain parameters
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config ip snmp ip snmp contact Eltex
show candidate-config ip ssh
Display candidate configuration for SSH.
Syntax
show candidate-config ip ssh
Parameters
The command does not contain parameters
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config ip ssh no ip ssh enable
show candidate-config ip telnet
Display candidate configuration for TELNET.
Syntax
show candidate-config ip telnet
Parameters
The command does not contain parameters
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config ip telnet no ip telnet enable
show candidate-config port-channel
Display the candidate configuration for port-channel.
Syntax
show candidate-config interface port-channel <PORT-CHANNEL-ID>
Parameters
<PORT-CHANNEL-ID> - port-channel ID. The parameter can be a range or an enumeration (e.g.: interface interface port-channel 1-5 or interface interface interface port-channel 1,5).
Privilege group
view-configuration, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show candidate-config interface port-channel 1-2 interface port-channel 1 vlan allow 20,99 exit interface port-channel 2 vlan allow 30 exit
show candidate-config port-channel load-balance
Display the candidate configuration for port-channel load balance.
Syntax
show candidate-config interface port-channel load-balance
Parameters
The command does not contain parameters.
Privilege group
view-configuration, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show candidate-config interface port-channel load-balance interface port-channel load-balance hash src-mac dst-mac interface port-channel load-balance polynomial 0x84a1
show candidate-config logging
Display candidate configuration for logging.
Syntax
show candidate-config logging
Parameters
The command does not contain parameters.
Privilege group
view-configuration, config-logging
Command mode
ROOT
Example
LTP-16N# show candidate-config logging logging module dna ont 1/1 loglevel debug exit
show candidate-config management
Displays the candidate configuration of network management settings.
Syntax
show candidate-config management
Parameters
The command does not contain parameters.
Privilege group
view-configuration, config-management
Command mode
ROOT
Example
LTP-16N# show candidate-config management management ip 192.168.1.100 management gateway 192.168.1.1 management vid 100
show candidate-config privilege
Display candidate configuration for privileges.
Syntax
show candidate-config privilege
Parameters
The command does not contain parameters.
Privilege group
view-configuration, config-user
Command mode
ROOT
Example
LTP-16N# show candidate-config privilege privilege 3 view-system
show candidate-config profile cross-connect
Display candidate configuration for cross-connect profile.
Syntax
show candidate-config profile cross-connect [NAME]
Parameters
[NAME] - profile name. Character set from 1 to 15 symbols long.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show candidate-config profile cross-connect HSI profile cross-connect HSI bridge enable bridge group 10 outer vid 100 exit
show candidate-config profile dba
Display candidate configuration for DBA profile.
Syntax
show candidate-config profile dba [NAME]
Parameters
[NAME] - profile name. Character set from 1 to 15 symbols long.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show candidate-config profile dba DBA profile dba DBA mode status-reporting exit
show candidate-config profile ports
Display candidate configuration for ports profile.
Syntax
show candidate-config profile ports [NAME]
Parameters
[NAME] - profile name. Character set from 1 to 15 symbols long.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show candidate-config profile ports profile ports pp port 1 bridge group 10 exit
show candidate-config profile management
Display candidate configuration for management interface profile.
Syntax
show candidate-config profile management [NAME]
Parameters
[NAME] - profile name. Character set from 1 to 15 symbols long.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show candidate-config profile management profile management MANAGEMENT iphost id 3 exit
show candidate-config profile dhcp-opt82
Display candidate configuration for dhcp-opt82 profile.
Syntax
show candidate-config profile dhcp-opt82 [NAME]
Parameters
[NAME] - profile name. Character set from 1 to 15 symbols long.
Privilege group
view-configuration, config-dhcp
Command mode
ROOT
Example
LTP-16N# show candidate-config profile dhcp-opt82 profile dhcp-opt82 DHCP-82 ont-sn-format numerical exit
show candidate-config profile pppoe-ia
Display candidate configuration for pppoe-ai profile.
Syntax
show candidate-config profile pppoe-ia [NAME]
Parameters
[NAME] - profile name. Character set from 1 to 15 symbols long.
Privilege group
view-configuration, config-pppoe
Command mode
ROOT
Example
LTP-16N# show candidate-config profile pppoe-ia profile pppoe-ia PPPOE ont-sn-format numerical exit
show candidate-config user
Display candidate configuration for users.
Syntax
show candidate-config user
Parameters
The command does not contain parameters.
Privilege group
view-configuration, config-user
Command mode
ROOT
Example
LTP-16N# show candidate-config user user test2 encrypted_password $6$XqyNfsV/$h.QgxTKh9PFGvO5nZ5jSuZqOC4Z274lDbSktK51YX8xmmsFUk9FmIUSqZDC7SOmVAtH3XBIR5bOYY5tra4T8j1 user test2 privilege 0
show candidate-config vlan
Display candidate configuration for VLAN.
Syntax
show candidate-config vlan <VID>
Parameters
<VID> - VLAN ID, in the range [1-4094].
Privilege group
view-configuration, config-vlan
Command mode
ROOT
Example
LTP-16N# show candidate-config vlan 100 vlan 100 ip igmp snooping enable exit
show date
Display current date.
Syntax
show date
Parameters
The command does not contain parameters.
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# show date Tue Sep 8 08:32:53 UTC 2020
show firmware
Display the list of firmwares in main and redundant areas. The select field marks which firmware will be loaded after rebooting. To upload firmware to the device you should use the copy command.
Syntax
show firmware
Parameters
The command does not contain parameters.
Privilege group
view-firmware
Command mode
ROOT
Example
LTP-16N# show firmware Select Type Version Build Date ------ ------ -------- ----- ---------------- * master 1.2.0 472 19.05.2021 09:18 ----------------------------------------------------- slave 1.2.0 467 17.05.2021 06:53 "*" designates that the image was selected for the next boot LTP-16N#
show firmware ont list
Display the list of firmware for ONT uploaded to the device. To upload firmware to the device you should use the copy command.
Syntax
show firmware ont list
Parameters
The command does not contain parameters.
Privilege group
view-firmware
Command mode
ROOT
Example
LTP-16N# show firmware ont list N | Firmware ---------------------------- 1 | ntu-1-3.28.0-build645.fw.bin ---------------------------- 2 | ntu-1-3.26.5.101.fw.bin ---------------------------- 3 | ntu-2-3.28.0.2387.fw.bin ---------------------------- 4 | ntu-rg-54xx-1.3.0.825.fw.bin ---------------------------- 5 | ntu-1-3.28.0-build648.fw.bin
show interface 10G-front-port <PORT-ID> counters
Display counters on 10G-front ports.
Syntax
show interface 10G-front-port <PORT-ID> counters
Parameters
<PORT-ID> - port index in the range [1-8]. The parameter can be set by a range or enumeration (For example: interface 10G-front-port 1-5 or interface 10G-front-port 1,5).
Privilege group
view-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface 10G-front-port 1 counters 10G-front-port 1 statistics Rx Bytes: 53201472 Rx Packets: 39119 Rx Multicast Packets: 39009 Rx Broadcast Packets: 110 Rx Error Packets: 0 Tx Bytes: 343079 Tx Packets: 3484 Tx Multicast Packets: 982 Tx Broadcast Packets: 0 Tx Error Packets: 0
show interface 10G-front-port <PORT-ID> counters verbose
Display counters on 10G-front ports in details.
Syntax
show interface 10G-front-port <PORT-ID> counters
Parameters
<PORT-ID> - port index in the range [1-8]. The parameter can be set by a range or enumeration (For example: interface 10G-front-port 1-5 or interface 10G-front-port 1,5).
Privilege group
view-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface 10G-front-port 8 counters verbose 10G-front-port 8 statistics Rx Bytes 3853048381 Rx Packets 2841701 Rx Unicast Packets 22085 Rx Multicast Packets 2819615 Rx Broadcast Packets 1 Rx Error Packets 0 Rx Unknown Proto Packets 0 Tx Bytes 2299253 Tx Packets 21890 Tx Unicast Packets 21831 Tx Multicast Packets 54 Tx Broadcast Packets 5 Tx Error Packets 0 Rx frames 64 526 Rx frames 65-127 22172 Rx frames 128-255 39 Rx frames 256-511 0 Rx frames 512-1023 0 Rx frames 1024-1518 2818965 Rx frames 1519-2047 0 Rx frames 2048-4095 0 Rx frames 4096-9216 0 Rx frames 9217-16383 0 Tx frames 64 2 Tx frames 65-127 21871 Tx frames 128-255 17 Tx frames 256-511 0 Tx frames 512-1023 0 Tx frames 1024-1518 0 Tx frames 1519-2047 0 Tx frames 2048-4095 0 Tx frames 4096-9216 0 Tx frames 9217-16383 0
show interface 10G-front-port <PORT-ID> state
Display 10G-front ports state.
Syntax
show interface 10G-front-port <PORT-ID> state
Parameters
<PORT-ID> - port index in the range [1-8]. The parameter can be set by a range or enumeration (For example: interface 10G-front-port 1-5 or interface 10G-front-port 1,5).
Privilege group
view-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface 10G-front-port 1 state Front-port Status Speed Media -------------------- -------------------- -------------------- -------------------- 1 up 1G copper
show interface ont <PORT-ID>[/ONT-ID] online
Display list of configured and online ONTs.
Syntax
show interface ont <PORT-ID>[/ONT-ID] online
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 ot interface ont 1,3,5,7).
[ONT-ID] - ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1 online ----------------------------------- GPON-port 1 ONT online list ----------------------------------- ## Serial ONT ID GPON-port RSSI Status 1 ELTX6C000090 1 1 -19.96 OK
show interface ont <PORT-ID>[/ONT-ID] offline
Display list of configured and offline ONTs.
Syntax
show interface ont <PORT-ID>[/ONT-ID] offline
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 ot interface ont 1,3,5,7).
[ONT-ID] - ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1 offline ----------------------------------- GPON-port 1 ONT offline list ----------------------------------- ## Serial ONT ID GPON-port Status 1 ELTX6C000090 1 1 OFFLINE
show interface ont <PORT-ID>[/ONT-ID] unactivated
Display list of unactivated ONTs.
Syntax
show interface ont <PORT-ID>[/ONT-ID] unactivated
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 ot interface ont 1,3,5,7).
[ONT-ID] - ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 unactivated ----------------------------------- pon-port 1 ONT unactivated list ----------------------------------- ## Serial ONT ID GPON-port RSSI Version EquipmentID Status 1 ELTX0600003D n/a 1 n/a n/a n/a UNACTIVATED
show interface ont <PORT-ID>[/ONT-ID] configured
Display list of configured ONTs.
Syntax
show interface ont <PORT-ID>[/ONT-ID] configured
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 ot interface ont 1,3,5,7).
[ONT-ID] - ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 configured ----------------------------------- GPON-port 1 ONT configured list ----------------------------------- ## Serial ONT ID GPON-port Status 1 ELTX6C000090 1 1 OK
show interface ont <PORT-ID>[/ONT-ID] unconfigured
Display list of free indexes on the port.
Syntax
show interface ont <PORT-ID>[/ONT-ID] unconfigured
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 ot interface ont 1,3,5,7).
[ONT-ID] - ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 3 unconfigured GPON-port 3 ONT unconfigured: 1-128
show interface ont <PORT-ID>[/ONT-ID] connected
Display list of non-activated and online ONTs.
Syntax
show interface ont <PORT-ID>[/ONT-ID] connected
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 ot interface ont 1,3,5,7).
[ONT-ID] - ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 connected ----------------------------------- pon-port 1 ONT connected list ----------------------------------- ## Serial ONT ID GPON-port RSSI Version EquipmentID Status 1 ELTX0600003D 1 1 -7.44 3.25.1.11 NTP-RG-1402G OK
show interface ont <PORT-ID>[/ONT-ID] counters gpon
Display GPON counters for ONT on the OLT side.
Syntax
show interface ont <PORT-ID>[/ONT-ID] counters gpon
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 ot interface ont 1,3,5,7).
[ONT-ID] - ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters gpon [ONT 1/1] GPON statistics Drift Positive: 0 Drift Negative: 0 Delimiter Miss Detection: 0 BIP Errors: 0 BIP Units: 104238772192 FEC Corrected symbols: 0 FEC Codewords Uncorrected: 0 FEC Codewords Uncorrected: 0 FEC Codewords: 0 FEC Corrected Units: 0 Rx PLOAMs Errors: 0 Rx PLOAMs Non Idle: 15 Rx OMCI: 405 Rx OMCI Packets CRC Error: 0 Rx Bytes: 40262 Rx Packets: 542 Tx Bytes: 19296 Tx Packets: 402 BER Reported: 0
show interface ont <PORT-ID>[/ONT-ID] counters gem-port
Display GEM port counters for ONT on the OLT side.
Syntax
show interface ont <PORT-ID>[/ONT-ID] counters gem-port
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 ot interface ont 1,3,5,7).
[ONT-ID] - ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters gem-port ONT [1/1] GEM port statistics GEM port id Rx Packet Rx Bytes Tx Packet Tx Bytes 129 135 20642 0 0 Broadcast 0 0 0 0 Multicast 0 0 13153 17964394
show interface ont <PORT-ID>[/ONT-ID] rssi
Display the signal power level.
Syntax
show interface ont <PORT-ID>[/ONT-ID] rssi
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 ot interface ont 1,3,5,7).
[ONT-ID] - ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 rssi ----------------------------------- [ONT1/1] RSSI ----------------------------------- Received signal strength indication: -19.913998 [dBm]
show interface ont <PORT-ID>[/ONT-ID] data-path
Display the configuration for this ONT.
Syntax
show interface ont <PORT-ID>[/ONT-ID] data-path
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 ot interface ont 1,3,5,7).
[ONT-ID] - ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 data-path Service #1: user vid: -1 pon vid: -1 outer vid 100 bridge_group: 10 t-cont id: 32768 alloc id: 767 gem port: 129 flow id: 63998 traffic model: MULTICAST 10G-front-port: 0 Bridge #0: Service profile id: 10 Broadcast enable: false Broadcast filters: 0 0 0 0 0 0 0 0 0 0 0 0 Multicast enable: true Multicast filters: 100 0 0 0 0 0 0 0 0 0 0 0 Port #0 Bridge group: 10 Pon vid: -1 User vid: -1 Multicast enable: true Port #1 Bridge group: 0 Pon vid: 0 User vid: 0 Multicast enable: false Port #2 Bridge group: 0 Pon vid: 0 User vid: 0 Multicast enable: false Port #3 Bridge group: 0 Pon vid: 0 User vid: 0 Multicast enable: false Alloc base #0 Scheme: share-t-cont Alloc ids: 767 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
show interface port-channel <PORT-CHANNEL-ID> counters
Display counters by port-channel.
Syntax
show interface port-channel <PORT-CHANNEL-ID> counters
Parameters
<PORT-CHANNEL-ID> - port-channel ID. The parameter can be a range or an enumeration (e.g.: interface interface port-channel 1-5 or interface interface interface port-channel 1,5).
Privilege group
view-interface-front-port, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface port-channel 1 counters Port UC packet recv MC packet recv BC packet recv Octets recv UC packet sent MC packet sent BC packet sent Octets sent ---- -------------- -------------- -------------- -------------- -------------- -------------- -------------- -------------- 1 0 28451 0 2966675 0 3604784 0 4926092069
show interface port-channel <PORT-CHANNEL-ID> counters verbose
Display counters by port-channel in details.
Syntax
show interface port-channel <PORT-CHANNEL-ID> counters verbose
Parameters
<PORT-CHANNEL-ID> - port-channel ID. The parameter can be a range or an enumeration (e.g.: interface interface port-channel 1-5 or interface interface interface port-channel 1,5).
Privilege group
view-interface-front-port, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface port-channel 32 counters verbose Port-channel 32 statistics Rx Bytes 4926092069 Rx Packets 3631835 Rx Unicast Packets 27049 Rx Multicast Packets 3604784 Rx Broadcast Packets 2 Rx Error Packets 0 Rx Unknown Proto Packets 0 Tx Bytes 2966675 Tx Packets 28855 Tx Unicast Packets 28451 Tx Multicast Packets 391 Tx Broadcast Packets 13 Tx Error Packets 0 Rx frames 64 560 Rx frames 65-127 27140 Rx frames 128-255 39 Rx frames 256-511 0 Rx frames 512-1023 0 Rx frames 1024-1518 3604094 Rx frames 1519-2047 0 Rx frames 2048-4095 0 Rx frames 4096-9216 0 Rx frames 9217-16383 0 Tx frames 64 2 Tx frames 65-127 28832 Tx frames 128-255 21 Tx frames 256-511 0 Tx frames 512-1023 0 Tx frames 1024-1518 0 Tx frames 1519-2047 0 Tx frames 2048-4095 0 Tx frames 4096-9216 0 Tx frames 9217-16383 0
show interface port-channel <PORT-CHANNEL-ID> state
Display state by port-channel.
Syntax
show interface port-channel <PORT-CHANNEL-ID> counters verbose
Parameters
<PORT-CHANNEL-ID> - port-channel ID. The parameter can be a range or an enumeration (e.g.: interface interface port-channel 1-5 or interface interface interface port-channel 1,5).
Privilege group
view-interface-front-port, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface port-channel 1 state Port-channel 1 status information: Status: up Common speed: 1G Front-port from channel status: Front-port 1 Status: up Media: copper Speed: 1G
show interface gpon-port <PORT-ID> state
Display state by gpon ports.
Syntax
show interface gpon <PORT-ID> state
Parameters
<ID> - port index in the range [1-16]. The parameter can be set by a range or enumeration (e.g.: interface gpon-port 1-5 or interface gpon-port 1,5).
Privilege group
view-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface gpon-port 1 state Port State ONT count SFP vendor SFP product number SFP vendor revision SFP temperature [C] SFP voltage [V] SFP tx bias current [mA] SFP tx power [dBm] ---- -------- --------- ------------------ ------------------ ------------------- ------------------- --------------- ------------------------ ------------------ 1 OK 1 Ligent Photonics LTE3680P-BH 1.0 52 3.27 17.55 5.35
show ip igmp snooping config vlan
Display IGMP configuration for a given VLAN.
Syntax
show ip igmp snooping config vlan <VID>
Parameters
<VID> - VLAN ID, in the range [1-4094].
Privilege group
view-igmp
Command mode
ROOT
Example
LTP-16N# show ip igmp snooping config vlan 99 --------------------- VLAN 99 IGMP settings --------------------- snooping: enabled fast leave: disabled querier: enabled learning: enabled multicast loopback: disabled robustness variable: 2 query interval: 125 query response interval: 100 querier ip address: 0.0.0.0 source ip address: 0.0.0.0 dscp: 0 igmp version: V1_V2_V3 mc router ports: none
show ip igmp snooping groups
Display the multicast group added via IGMP. With VLAN ID filtering capability.
Syntax
show ip igmp snooping groups[vlan <VID>]
Parameters
<VID> - VLAN ID, in the range [1-4094].
Privilege group
view-igmp
Command mode
ROOT
Example
LTP-16N# show ip igmp snooping groups VLAN 99: groups count - 1 1: 239.25.25.25 Filter mode EXCLUDE Member gpon-port 1, expires 00:05:34 Filter mode EXCLUDE Group expires 00:05:34
show ip igmp snooping hosts
Display the list of ports with connected hosts. With VLAN ID filtering capability.
Syntax
show ip igmp snooping hosts [vlan <VID>]
Parameters
<VID> - VLAN ID, in the range [1-4094].
Privilege group
view-igmp
Command mode
ROOT
Example
LTP-16N# show ip igmp snooping hosts vlan 99 Hosts ports. VLAN 99. gpon-port 1 00:00:00 gpon-port 2 00:00:00 gpon-port 3 00:00:00 gpon-port 4 00:00:00 gpon-port 5 00:00:00 gpon-port 6 00:00:00 gpon-port 7 00:00:00 gpon-port 8 00:00:00 gpon-port 9 00:03:15 gpon-port 10 00:00:00 gpon-port 11 00:00:00 gpon-port 12 00:00:00 gpon-port 13 00:00:00 gpon-port 14 00:00:00 gpon-port 15 00:00:00 gpon-port 16 00:00:00
show ip igmp snooping mroute
Display the list of ports with connected mroute. With VLAN ID filtering capability.
Syntax
show ip igmp snooping mroute [vlan <VID>]
Parameters
<VID> - VLAN ID, in the range [1-4094].
Privilege group
view-igmp
Command mode
ROOT
Example
LTP-16N# show ip igmp snooping mrouters Multicast routers ports. VLAN 99. front-port 1 00:00:00
show ip dhcp sessions
Display active dhcp sessions.
Syntax
show ip dhcp sessions
Parameters
The command does not contain parameters.
Privilege group
view-dhcp
Command mode
ROOT
Example
LTP-16N# show ip dhcp sessions DHCP sessions (1): ## Serial GPON-port ONT-ID Service IP MAC Vid GEM Life time ---- ------------ --------- ------ ------- --------------- ----------------- ---- ---- --------- 1 ELTX6C000090 1 1 1 192.168.101.75 E0:D9:E3:6A:28:F0 1100 129 3503
show ip dhcp sessions <FILTER>
Display active dhcp sessions by filter.
Syntax
show ip dhcp sessions <FILTER> <VALUE>
Parameters
<FILTER> - filters for MAC table:
- interface - filter dhcp sessions by interface type. <VALUE> values are available for this filter:
- gpon-port - filter dhcp sessions of the specified gpon-ports;
- ont- filter dhcp sessions of the specified ont;
- vlan - filter dhcp sessions by vlan. <VALUE> values are available for this filter:
- vlan index [1-4094]. The parameter can be specified as a range or an enumeration (For example: vlan 10-30 or vlan 10,40,70).
Privilege group
view-dhcp
Command mode
ROOT
Example
LTP-16N# show ip dhcp sessions interface ont 1/1 DHCP sessions (1): ## Serial GPON-port ONT-ID Service IP MAC Vid GEM Life time ---- ------------ --------- ------ ------- --------------- ----------------- ---- ---- --------- 1 ELTX6C000090 1 1 1 192.168.101.75 E0:D9:E3:6A:28:F0 1100 129 3503
show ip pppoe sessions
Display active dhcp sessions.
Syntax
show ip pppoe sessions
Parameters
The command does not contain parameters.
Privilege group
view-pppoe
Command mode
ROOT
Example
LTP-16N# show ip pppoe sessions PPPoE sessions (2): ## Serial GPON-port Ont ID GEM Client MAC Session ID Duration Unblock ---- ------------ --------- ------ ---- ----------------- ---------- --------- --------- 1 ELTX74000A34 8 20 882 E0:D9:E3:9C:D4:5B 0x39cf 0:07:02 0:00:00 2 ELTX7400018C 7 31 1190 E0:D9:E3:9C:C3:0C 0x0eb4 0:06:54 0:00:00
show ip pppoe sessions <FILTER>
Display active dhcp sessions by filter.
Syntax
show ip pppoe sessions <FILTER> <VALUE>
Parameters
<FILTER> - filters for MAC table:
- interface - filter ppoe sessions by interface type. <VALUE> values are available for this filter:
- gpon-port - filter ppoe sessions of the specified gpon-ports;
- ont- filter ppoe sessions of the specified ont;
- vlan - filter ppoe sessions by vlan. <VALUE> values are available for this filter:
- vlan index [1-4094]. The parameter can be specified as a range or an enumeration (For example: vlan 10-30 or vlan 10,40,70).
Privilege group
view-pppoe
Command mode
ROOT
Example
LTP-16N# show ip pppoe sessions interface gpon 8 PPPoE sessions (1): ## Serial GPON-port Ont ID GEM Client MAC Session ID Duration Unblock ---- ------------ --------- ------ ---- ----------------- ---------- --------- --------- 1 ELTX74000A34 8 20 882 E0:D9:E3:9C:D4:5B 0x39cf 0:07:02 0:00:00
show license
Display information on the current license.
Syntax
show license
Parameters
The command does not contain parameters.
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# show license Active license information: License valid: yes Version: 1.2 Board SN: GP3D000033 Licensed vendor: all Licensed ONT count: unlimited Licensed ONT online: n/a
show log buffer
Display last log from buffer.
Syntax
show log buffer
Parameters
The command does not contain parameters.
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# show log buffer 09 Sep 11:49:31 NOTICE DNA BCM-API - Device reset: OK 09 Sep 11:49:51 NOTICE DNA BCM-API - Device connection is complete system_mode is gpon__16_x 09 Sep 11:49:51 NOTICE DNA BCM-API - Connect to device: OK 09 Sep 11:49:51 NOTICE DNA BCM-API - Qumran CLI command (vlan create 3470 pbm=ge140) execution: OK 09 Sep 11:49:51 NOTICE DNA BCM-API - Qumran CLI command (port xe128 speed=1000) execution: OK 09 Sep 11:49:51 NOTICE DNA BCM-API - Qumran CLI command (vlan add 3470 pbm=xe128) execution: OK 09 Sep 11:49:51 NOTICE DNA BCM-API - Getting 1 front-port info: OK 09 Sep 11:49:51 NOTICE DNA BCM-API - Getting 2 front-port info: OK 09 Sep 11:49:51 NOTICE DNA BCM-API - Getting 3 front-port info: OK 09 Sep 11:49:51 NOTICE DNA BCM-API - Getting 4 front-port info: OK 09 Sep 11:49:51 NOTICE DNA BCM-API - Getting 5 front-port info: OK 09 Sep 11:49:51 NOTICE DNA BCM-API - Getting 6 front-port info: OK 09 Sep 11:49:51 NOTICE DNA BCM-API - Getting 7 front-port info: OK 09 Sep 11:49:51 NOTICE DNA BCM-API - Getting 8 front-port info: OK
show log files
Display list of files with logs.
Syntax
show log files
Parameters
The command does not contain parameters.
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# show log files ## Name Size in bytes Date of last modification 1 LTP.log.2 109640 Tue Sep 8 10:11:18 2020 2 LTP.log.3 120404 Tue Sep 8 10:11:18 2020 3 LTP.log 3340 Tue Sep 8 10:27:40 2020 Total files: 3
show log <FILENAME>
Display logs from file.
Syntax
show log <FILENAME>
Parameters
<FILENAME> - file name from the list that available by the show log files command.
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# show log LTP.log 09 Sep 11:50:51 NOTICE DNA BCM-API - ONT 1/1 activation: OK 09 Sep 11:51:01 NOTICE DNA BCM-API - Found unactivated ONU ELTX6C000090 on GPON-PORT 1 09 Sep 11:51:01 NOTICE ONT 1/1 - Activation: OK 09 Sep 11:51:03 NOTICE ONT 1/1 - ONT Vendor: ELTX Type: NTU1421GCWAC (1v1) FW version: 3.40.2.109 09 Sep 11:51:03 NOTICE DNA BCM-API - Alloc-ID 767 (ONT 1/1) creation: OK 09 Sep 11:51:03 NOTICE DNA BCM-API - Flow (id 63998, type 0) destruction: OK 09 Sep 11:51:03 NOTICE DNA BCM-API - Upstream flow 63998 creation: OK 09 Sep 11:51:03 NOTICE FSM-PON - OLT side datapath configured. 09 Sep 11:51:04 NOTICE ONT 1/1 - ONT_OK Successful activation and configuration 09 Sep 11:51:19 NOTICE DNA BCM-API - Flow (id 1598, type 2) destruction: OK 09 Sep 11:51:19 NOTICE DNA BCM-API - Multicast flow 1598 creation: OK 09 Sep 11:51:19 NOTICE DNA BCM-API - Updating group #0, command - add: OK 09 Sep 11:51:32 NOTICE DNA BCM-API - Flow (id 63998, type 0) destruction: OK 09 Sep 11:51:32 NOTICE DNA BCM-API - Alloc-ID 767 (PON port 1) destruction: OK
show running-config
Display current running configuration.
Syntax
show running-config
Parameters
The command does not contain parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config configure terminal management ip 192.168.100.1 exit commit exit
show running-config all
Display all current running configuration, including default values.
Syntax
show running-config all
Parameters
The command does not contain parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config all configure terminal interface gpon-port 1 no shutdown exit interface gpon-port 2 no shutdown exit interface gpon-port 3 no shutdown exit interface gpon-port 4 no shutdown exit interface gpon-port 5 no shutdown exit interface gpon-port 6 no shutdown exit interface gpon-port 7 no shutdown exit interface gpon-port 8 --More--(0%)
show running-config alarm
Display the running configuration for alarms. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config alarm [all]
Parameters
The command does not contain parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config alarm LTP-16N# show running-config alarm all alarm system-fan max-rpm 12000 system-fan min-rpm 2000 system-fan severity critical system-fan in true system-fan out true system-load-average level 0 system-load-average severity critical system-load-average in true system-load-average out true system-ram free 12 system-ram severity critical system-ram in true system-ram out true system-temperature sensor gpon-ports-1 min 0 system-temperature sensor gpon-ports-1 max 70 system-temperature sensor gpon-ports-2 min 0 system-temperature sensor gpon-ports-2 max 70 system-temperature sensor front-ports min 0 system-temperature sensor front-ports max 70 system-temperature sensor switch min 0 system-temperature sensor switch max 70 system-temperature severity critical --More--(46%)
show running-config interface 10G-front-port
Display the running configuration for 10G-front-port. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config interface 10G-front-port <PORT-ID> [all]
Parameters
<PORT-ID> - port index in the range [1-8]. The parameter can be set by a range or enumeration (For example: interface 10G-front-port 1-5 or interface 10G-front-port 1,5).
Privilege group
view-configuration, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show running-config interface 10G-front-port 1-2 all interface 10G-front-port 1 no shutdown no vlan allow 1-4094 switchport mode trunk exit interface 10G-front-port 2 no shutdown no vlan allow 1-4094 switchport mode trunk exit
show running-config interface gpon-port
Display running configuration for gpon-port. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config interface gpon-port <PORT-ID> [all]
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface gpon-port 1-3 ot interface gpon-port 1,3,5,7).
Privilege group
view-configuration, config-interface-gpon-port
Command mode
ROOT
Example
LTP-16N# show running-config interface gpon-port 15,16 all interface gpon-port 15 no shutdown exit interface gpon-port 16 no shutdown exit
show running-config interface ont
Display the running configuration for ONT. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config interface ont <PORT-ID>[/ONT-ID] [all]
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 ot interface ont 1,3,5,7).
[ONT-ID] - ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-configuration, config-interface-ont
Command mode
ROOT
Example
LTP-16N# show running-config interface ont 1/1 all interface ont 1/1 service 1 profile cross-connect "" dba "" service 2 profile cross-connect "" dba "" service 3 profile cross-connect "" dba "" service 4 profile cross-connect "" dba "" service 5 profile cross-connect "" dba "" service 6 profile cross-connect "" dba "" service 7 profile cross-connect "" dba "" service 8 profile cross-connect "" dba "" service 9 profile cross-connect "" dba "" service 10 profile cross-connect "" dba "" service 11 profile cross-connect "" dba "" service 12 profile cross-connect "" dba "" service 13 profile cross-connect "" dba "" service 14 profile cross-connect "" dba "" service 15 profile cross-connect "" dba "" service 16 profile cross-connect "" dba "" service 17 profile cross-connect "" dba "" service 18 profile cross-connect "" dba "" service 19 profile cross-connect "" dba "" service 20 profile cross-connect "" dba "" service 21 profile cross-connect "" dba "" service 22 profile cross-connect "" dba "" --More--(63%)
show running-config ip dhcp
Display running configuration for DHCP. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config ip dhcp
Parameters
The command does not contain parameters
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config ip dhcp ip dhcp snooping enable exit
show running-config ip igmp
Display running configuration for IGMP. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config ip igmp
Parameters
The command does not contain parameters
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config ip igmp ip igmp snooping
show running-config ip pppoe
Display running configuration for PPPoE. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config ip pppoe
Parameters
The command does not contain parameters
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config ip pppoe ip pppoe snooping enable exit
show running-config ip snmp
Display candidate configuration for SNMP. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config ip snmp
Parameters
The command does not contain parameters
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config ip snmp ip snmp contact Eltex
show running-config ip ssh
Display running configuration for SSH. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config ip ssh
Parameters
The command does not contain parameters
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config ip ssh no ip ssh enable
show running-config ip telnet
Display running configuration for TELNET. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config ip telnet
Parameters
The command does not contain parameters
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config ip telnet no ip telnet enable
show running-config port-channel
Display running configuration for port-channel. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config interface port-channel <PORT-CHANNEL-ID>
Parameters
<PORT-CHANNEL-ID> - port-channel ID. The parameter can be a range or an enumeration (e.g.: interface interface port-channel 1-5 or interface interface interface port-channel 1,5).
Privilege group
view-configuration, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show running-config interface port-channel 1 interface port-channel 1 vlan allow 99 exit
show candidate-config port-channel load-balance
Display the running configuration for port-channel load balance. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config interface port-channel load-balance
Parameters
The command does not contain parameters.
Privilege group
view-configuration, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show running-config interface port-channel load-balance interface port-channel load-balance hash src-mac dst-mac interface port-channel load-balance polynomial 0x84a1
show running-config logging
Display running configuration for logging. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config logging [all]
Parameters
The command does not contain parameters.
Privilege group
view-configuration, config-logging
Command mode
ROOT
Example
LTP-16N# show running-config logging all logging module dna loglevel notice module dna bcm-api loglevel notice module dna tools loglevel notice module dna loglib loglevel notice module dna cfgdb loglevel notice module dna conf-task loglevel notice module dna olt loglevel notice module dna gpon-port 1 loglevel notice module dna gpon-port 2 loglevel notice module dna gpon-port 3 loglevel notice module dna gpon-port 4 loglevel notice module dna gpon-port 5 loglevel notice module dna gpon-port 6 loglevel notice module dna gpon-port 7 loglevel notice module dna gpon-port 8 loglevel notice module dna gpon-port 9 loglevel notice module dna gpon-port 10 loglevel notice module dna gpon-port 11 loglevel notice module dna gpon-port 12 loglevel notice module dna gpon-port 13 loglevel notice module dna gpon-port 14 loglevel notice module dna gpon-port 15 loglevel notice --More--(1%)
show running-config management
Display the running configuration of network management settings. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config management [all]
Parameters
The command does not contain parameters.
Privilege group
view-configuration, config-management
Command mode
ROOT
Example
LTP-16N# show running-config management all management ip 192.168.1.2 management mask 255.255.255.0 management gateway 0.0.0.0 management vid 1
show running-config privilege
Display running configuration for privileges. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config privilege [all]
Parameters
The command does not contain parameters.
Privilege group
view-configuration, config-user
Command mode
ROOT
Example
LTP-16N# show running-config privilege all privilege 1 view-interface-ont privilege 2 view-interface-ont privilege 2 commands-interface-ont privilege 4 view-interface-ont privilege 4 config-general privilege 4 config-interface-ont privilege 4 commands-interface-ont privilege 4 commands-configuration privilege 5 view-interface-ont privilege 5 config-general privilege 5 config-interface-ont privilege 5 config-interface-ont-profile privilege 5 commands-interface-ont privilege 5 commands-configuration privilege 6 view-interface-ont privilege 6 config-general privilege 6 config-interface-gpon-port privilege 6 config-interface-ont privilege 6 config-interface-ont-profile privilege 6 commands-interface-ont privilege 6 commands-configuration privilege 6 commands-interface-gpon-port privilege 7 view-igmp --More--(18%)
show running-config profile cross-connect
Display running configuration for cross-connect profile. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config profile cross-connect [NAME] [all]
Parameters
[NAME] - profile name. Character set from 1 to 15 symbols long.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show running-config profile cross-connect HSI profile cross-connect HSI bridge enable bridge group 10 outer vid 100 exit LTP-16N# show running-config profile cross-connect all profile cross-connect HSI pon vid no-change user vid untagged description bridge enable bridge group 10 outer vid 100 traffic-model n-to-1 exit
show running-config profile dba
Display running configuration for DBA profile. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config profile dba [NAME] [all]
Parameters
[NAME] - profile name. Character set from 1 to 15 symbols long.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show running-config profile dba all profile dba dba description bandwidth besteffort 1244160 bandwidth guaranteed 512 allocation-scheme share-t-cont mode non-status-reporting exit
show running-config profile ports
Display running configuration for ports profile. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config profile ports [NAME] [all]
Parameters
[NAME] - profile name. Character set from 1 to 15 symbols long.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show running-config profile ports profile ports pp port 1 bridge group 10 exit LTP-16N# show running-config profile ports all profile ports pp no port 1 multicast port 1 bridge group 10 port 1 igmp downstream priority 0 port 1 igmp downstream tag-control pass port 1 igmp downstream vid 0 port 1 igmp upstream priority 0 port 1 igmp upstream tag-control pass port 1 igmp upstream vid 0 no port 2 multicast port 2 bridge group 0 port 2 igmp downstream priority 0 port 2 igmp downstream tag-control pass port 2 igmp downstream vid 0 port 2 igmp upstream priority 0 port 2 igmp upstream tag-control pass port 2 igmp upstream vid 0 no port 3 multicast port 3 bridge group 0 port 3 igmp downstream priority 0 port 3 igmp downstream tag-control pass port 3 igmp downstream vid 0 port 3 igmp upstream priority 0 port 3 igmp upstream tag-control pass port 3 igmp upstream vid 0 no port 4 multicast port 4 bridge group 0 port 4 igmp downstream priority 0 port 4 igmp downstream tag-control pass port 4 igmp downstream vid 0 port 4 igmp upstream priority 0 port 4 igmp upstream tag-control pass port 4 igmp upstream vid 0 igmp mode snooping igmp querier igmp robustness 2 igmp version 3 igmp query interval 125 --More--(94%)
show running-config profile management
Display running configuration for management interface profile. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config profile management [NAME]
Parameters
[NAME] - profile name. Character set from 1 to 15 symbols long.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show candidate-config profile management profile management MANAGEMENT iphost id 3 exit
show running-config profile dhcp-opt82
Display running configuration for dhcp-opt82 profile.
Syntax
show running-config profile dhcp-opt82 [NAME]
Parameters
[NAME] - profile name. Character set from 1 to 15 symbols long.
Privilege group
view-configuration, config-dhcp
Command mode
ROOT
Example
LTP-16N# show running-config profile dhcp-opt82 profile dhcp-opt82 DHCP-82 ont-sn-format numerical exit
show running-config profile pppoe-ia
Display running configuration for pppoe-ai profile.
Syntax
show running-config profile pppoe-ia [NAME]
Parameters
[NAME] - profile name. Character set from 1 to 15 symbols long.
Privilege group
view-configuration, config-pppoe
Command mode
ROOT
Example
LTP-16N# show running-config profile pppoe-ia profile pppoe-ia PPPOE ont-sn-format numerical exit
show running-config user
Display running configuration for users. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config user [all]
Parameters
The command does not contain parameters.
Privilege group
view-configuration, config-user
Command mode
ROOT
Example
LTP-16N# show running-config user user test encrypted_password $6$YocBrXdZ$/QPfwUYYrSdXgTm4YpCvo7D5sxiq0gfQ.Lbf.xaEDMvXLE9DqD/6HEG4sBSKfbA1uicizAr0SIIJRqgdgeuii0 user test privilege 0
show running-config vlan
Display running configuration for VLAN. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config vlan <VID> [all]
Parameters
<VID> - VLAN ID, in the range [1-4094].
Privilege group
view-configuration, config-vlan
Command mode
ROOT
Example
LTP-16N# show running-config vlan 1000 vlan 1000 ip igmp snooping enable exit LTP-16N# show running-config vlan 1000 all vlan 1000 name ip igmp snooping enable ip igmp snooping querier enable ip igmp query-interval 125 ip igmp query-response-interval 100 ip igmp robustness-variable 2 ip igmp last-member-query-interval 10 ip igmp snooping replace source-ip 0.0.0.0 ip igmp snooping querier ip-address 0.0.0.0 no ip igmp snooping querier fast-leave ip igmp snooping querier dscp 0 ip igmp version v1-v2-v3 ip igmp snooping mrouter gpon-port 1 ip igmp snooping mrouter gpon-port 2 ip igmp snooping mrouter gpon-port 3 ip igmp snooping mrouter gpon-port 4 ip igmp snooping mrouter gpon-port 5 ip igmp snooping mrouter gpon-port 6 ip igmp snooping mrouter gpon-port 7 ip igmp snooping mrouter gpon-port 8 ip igmp snooping mrouter gpon-port 9 ip igmp snooping mrouter gpon-port 10 --More--(58%)
show system environment
Display device system information.
Syntax
show system environment
Parameters
The command does not contain parameters.
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# show system environment System information: CPU load average (1m, 5m, 15m): 4.540 2.380 0.960 Free RAM/Total RAM (Gb): 4.59/7.76 Free disk space/Total disk space(Gb)): 5.73/6.13 Temperature: Sensor PON SFP 1 (*C): 50 Sensor PON SFP 2 (*C): 37 Sensor Front SFP (*C): 41 Sensor Switch (*C): 35 Fan state: Fan 1 (rpm): offline Fan 2 (rpm): offline Fan 3 (rpm): offline Fan 4 (rpm): offline Power supply information: Module 1: offline Module 2: PM160 220/12 1vX Type: AC Intact: true HW information FPGA version: 2.0 PLD version: 2.0 Factory Type: LTP-16N Revision: 1v2 SN: GP3D000026 MAC: E0:D9:E3:FF:24:B0
show version
Display current firmware version.
Syntax
show version
Parameters
The command does not contain parameters.
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# LTP-16N# show version Eltex LTP-16N: software version 1.0.0 build 1128 on 08.09.2020 05:44
show mac
Display MAC table.
Syntax
show mac
Parameters
The command does not contain parameters.
Privilege group
config-vlan, config-igmp, config-general, config-system, config-logging, config-interface-gpon-port, config-interface-ont, config-interface-ont-profile,
config-interface-front-port, config-access, config-cli, config-management, config-user
Command mode
ROOT
Example
LTP-16N# show mac Loading MAC table... MAC port A8:F9:4B:81:43:00 10G-front-port 11 MAC entries
show mac <FILTER>
Display MAC table by filter.
Syntax
show mac interface <FILTER> <VALUE>
Parameters
<FILTER> - filters for MAC table:
- interface - filter MAC table by interface type. <VALUE> values are available for this filter:
- 10G-front-port - filter MAC addresses of the specified 10G-front-ports;
- gpon-port - filter MAC addresses of the specified gpon-ports;
- port-channel - filter MAC addresses of the specified port-channels;
- vlan - filter MAC table by vlan. <VALUE> values are available for this filter:
- vlan index [1-4094]. The parameter can be specified as a range or an enumeration (For example: vlan 10-30 or vlan 10,40,70).
Privilege group
- show mac interface: config-vlan, config-igmp, config-general, config-system, config-logging, config-interface-gpon-port, config-interface-ont, config-interface-ont-profile, config-interface-front-port, config-access, config-cli, config-management, config-user;
- show mac vlan: view-configuration, view-firmware, config-vlan, config-igmp, config-ppoe, config-general, config-system, config-logging, config-interface-gpon-port, config-interface-ont, config-interface-ont-profile, config-interface-front-port.
Command mode
ROOT
Example
LTP-16N# show mac vlan 5 Loading MAC table... MAC port B4:2E:99:98:0C:76 10G-front-port 5 1 MAC entries