alarm
Switch to alarm configuration mode.
Syntax
alarm
Parameters
The command does not contain parameters.
Privilege group
config-general
Command mode
CONFIG
Example
LTP-16N(configure)# alarm
cli timeout
CLI session timeout configuration. (timeout - user inactivity time after which the session ends).
Syntax
cli timeout <VALUE>
no cli timeout
Parameters
<VALUE> - timeout value in the range [5-157680000] seconds.
Default value
1800
Privilege group
config-cli
Command mode
CONFIG
Example
LTP-16N(configure)# cli timeout 3600
cli max-session
Set the maximum number of CLI sessions that can be simultaneously connected to the device.
Syntax
cli max-sessions <VALUE>
no cli max-session
Parameters
<VALUE> - number of sessions [1-5].
Default value
5
Privilege group
config-cli
Command mode
CONFIG
Example
LTP-16N(configure)# cli max-session 2
interface 10G-front-port
Switch to the front ports configuration mode.
Syntax
[no] interface 10G-front-port <ID>
Parameters
<ID> - port index in the range [1-8]. The parameter can be set by a range or enumeration (For example: interface 10G-front-port 1-5 or interface 10G-front-port 1,5).
Privilege group
config-interface-front-port
Command mode
CONFIG
Example
LTP-16N(configure)# interface 10G-front-port 1-5
interface gpon-port
Switch to the gpon ports configuration mode.
Syntax
[no] interface gpon-port <ID>
Parameters
<ID> - port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface gpon-port 1-5 or interface gpon-port 10,12).
Privilege group
config-interface-gpon-port
Command mode
CONFIG
Example
LTP-16N(configure)# interface gpon-port 2-4,5
interface ont
Switch to ONT configuration mode.
Syntax
[no] interface ont <PORT-ID>[/ONT-ID]
Parameters
<PORT-ID> - gpon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 ot interface ont 1,3,5,7).
[ONT-ID] - ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
config-interface-ont
Command mode
CONFIG
Example
LTP-16N(configure)# interface ont 1/68,69
interface port-channel
Switch to the port-channel configuration mode.
Syntax
[no] interface port-channel <PORT-CHANNEL-ID>
Parameters
<PORT-CHANNEL-ID> - port-channel group index in the range of [1-32].
Privilege group
config-interface-front-port
Command mode
CONFIG
Example
LTP-16N(configure)# interface port-channel
interface port-channel load-balance polynomial
This command sets the polynomial to calculate the CRC.
Syntax
interface port-channel load-balance polynomial <POLYNOMIAL>
no interface port-channel load-balance polynomial
Parameters
<POLYNOMIAL> - polynomial. Possible values:
- 0x8003
- 0x8101
- 0x84a1
- 0x9019
Privilege group
config-interface-front-port
Command mode
CONFIG
Example
LTP-16N(configure)# interface port-channel load-balance polynomial 0x8101
interface port-channel load-balance hash
This command sets the fields in the package from which the hash will be calculated.
Syntax
interface port-channel load-balance hash <PACKAGE-FIELDS>
no interface port-channel load-balance hash
Parameters
<PACKAGE-FIELDS> - fields in the package from which the hash will be calculated. You can select from one to three fields:
- src-mac - source MAC address
- dst-mac - destination MAC address
- vlan - vlan field;
- ethertype - ethertype field.
Privilege group
config-interface-front-port
Command mode
CONFIG
Example
LTP-16N(configure)# interface port-channel load-balance hash src-mac vlan ethertype
ip dhcp
Switch to the DHCP configuration mode.
Syntax
ip dhcp
Parameters
The command does not contain parameters.
Privilege group
config-dhcp
Command mode
CONFIG
Example
LTP-16N(configure)# ip dhcp
ip pppoe
Switch to the PPPoE configuration mode.
Syntax
ip pppoe
Parameters
The command does not contain parameters.
Privilege group
config-pppoe
Command mode
CONFIG
Example
LTP-16N(configure)# ip pppoe
ip ssh enable
Enable terminal availability via SSH protocol.
Syntax
[no] ip ssh enable
Parameters
The command does not contain parameters.
Default value
Enabled.
Privilege group
config-access
Command mode
CONFIG
Example
LTP-16N(configure)# ip ssh enable
ip telnet enable
Enable terminal availability via TELNET protocol.
Syntax
[no] ip telnet enable
Parameters
The command does not contain parameters.
Default value
Enabled.
Privilege group
config-access
Command mode
CONFIG
Example
LTP-16N(configure)# ip telnet enable
ip snmp community
SNMP community configuration.
Syntax
ip snmp community <ID> <NAME> <ACCESS>
no ip snmp community <ID>
Parameters
<ID> - Community ID. May take values from 1 to 6;
<NAME> - SNMP community name. String, from 1 to 64 characters;
<ACCESS> - Level of access to SNMP tables. May take two values:
- ro - read only;
- rw - read write.
Privilege group
config-access
Command mode
CONFIG
Example
LTP-16N(configure)# ip snmp community 1 myCommunity access rw
ip snmp contact
This command sets the SNMP contact.
Syntax
ip snmp contact <NAME>
no ip snmp contact
Parameters
<NAME> - SNMP community name. String, from 1 to 255 characters.
Privilege group
config-access
Command mode
CONFIG
Example
LTP-16N(configure)# ip snmp contact ELTEX
ip snmp enable
This command enables SNMP on the device.
Syntax
[no] ip ssh enable
Parameters
The command does not contain parameters.
Default value
Enabled.
Privilege group
config-access
Command mode
CONFIG
Example
LTP-16N(configure)# ip snmp enable
ip snmp engine-id
This command sets SNMP engine id.
Syntax
ip snmp engine-id <ENGINE-ID>
no ip snmp engine-id
Parameters
<ENGINE-ID> - SNMP engine id. Possible values:
- generate - generate engine-id;
- A string of hex numbers, ranging in length from 10 to 64 characters.
Default value
Enabled.
Privilege group
config-access
Command mode
CONFIG
Example
LTP-16N(configure)# ip snmp engine-id 53e679ad83da7419350904efb9
ip snmp location
This command sets the device location for SNMP.
Syntax
ip snmp location <LOCATION>
no ip snmp location
Parameters
<LOCATION> - device location for SNMP. String, from 1 to 255 characters.
Privilege group
config-access
Command mode
CONFIG
Example
LTP-16N(configure)# ip snmp location Novosibirsk
ip snmp trap-community
This command sets trap community for SNMP.
Single SNMP trap community is used for all SNMP trap destination addresses.
Syntax
ip snmp trap-community <COMMUNITY>
no ip snmp trap-community
Parameters
<COMMUNITY> - SNMP trap community name. String, from 1 to 64 characters.
Privilege group
config-access
Command mode
CONFIG
Example
LTP-16N(configure)# ip snmp trap-community myCommunity
ip snmp traps
This command sets destination addresses and types of SNMP traps they accept.
Syntax
ip snmp traps <IP-ADDR> type <TYPE>
Parameters
- <IP-ADDR> - ip-address where the SNMP traps will be sent;
- <TYPE> - type of sent SNMP traps.
Default value
Enabled.
Privilege group
config-access
Command mode
CONFIG
Example
LTP-16N(configure)# ip snmp traps 192.168.1.5 type v2
ip snmp user
This command is used to configure SNMPv3 users.
Syntax
ip snmp traps <NAME> auth-passsword [AUTH-PASS] enc-password [ENC-PASS] access [ACCESS]
Parameters
- <NAME> - user name. String from 1 to 31 characters. Must not contain such characters as: '-', '_', '=', '+';
- [AUTH-PASS] - authentication password. String from 8 to 31 characters;
- [ENC-PASS] - encryption password. String from 8 to 31 characters;
- [ACCESS] - user access level. Possible values:
- ro - read only;
- rw - read/write.
Privilege group
config-access
Command mode
CONFIG
Example
LTP-16N(configure)# ip snmp user USER enc-password 1234567890 access rw
logging
Switch to the logging configuration mode.
Syntax
logging
Parameters
The command does not contain parameters.
Privilege group
config-logging
Command mode
CONFIG
Example
LTP-16N(configure)# logging
management ip
Set device IP address.
Syntax
management ip <IP>
no management ip
Parameters
<IP> - IP address, specified as AAA. BBB. CCC. DDD, where each part takes the value [0..255].
Default value
192.168.1.2
Privilege group
config-management
Command mode
CONFIG
Example
LTP-16N(configure)# management ip 192.168.1.3
management mask
Set device IP mask.
Syntax
management mask <IP>
no management mask
Parameters
<IP> - IP mask, specified as AAA. BBB. CCC. DDD, where each part takes the value [0..255].
Default value
255.255.255.0
Privilege group
config-management
Command mode
CONFIG
Example
LTP-16N(configure)# management mask 255.255.0.0
management gateway
Set the default gateway address.
Syntax
management gateway <IP>
no management gateway
Parameters
<IP> - IP address, specified as AAA. BBB. CCC. DDD, where each part takes the value [0..255].
Default value
0.0.0.0
Privilege group
config-management
Command mode
CONFIG
Example
LTP-16N(configure)# management gateway 192.168.100.1
management vid
Set vlan to access the device.
Syntax
management vid <VID>
no management vid
Parameters
<VID> - VLAN ID, in the range [1-4094].
Default value
1
Privilege group
config-management
Command mode
CONFIG
Example
LTP-16N(configure)# management vid 100
profile cross-connect
Switch to the cross-connect profile configuration mode.
Syntax
[no] profile cross-connect <NAME>
Parameters
<NAME> - profile name. Character set from 1 to 15 symbols long.
Privilege group
config-interface-ont-profile
Command mode
CONFIG
Example
LTP-16N(configure)# profile cross-connect HSI
profile ports
Switch to the ports profile configuration mode.
Syntax
[no] profile ports <NAME>
Parameters
<NAME> - profile name. Character set from 1 to 15 symbols long.
Privilege group
config-interface-ont-profile
Command mode
CONFIG
Example
LTP-16N(configure)# profile ports BRIDGRE
profile dba
Switch to the DBA profile configuration mode.
Syntax
[no] profile ports <NAME>
Parameters
<NAME> - profile name. Character set from 1 to 15 symbols long.
Privilege group
config-interface-ont-profile
Command mode
CONFIG
Example
LTP-16N(configure)# profile dba DBA-HSI
profile management
Switch to the Management profile configuration mode.
Syntax
[no] profile management <NAME>
Parameters
<NAME> - profile name. Character set from 1 to 15 symbols long.
Privilege group
config-management
Command mode
CONFIG
Example
LTP-16N(configure)# profile management MANAGE-PROFILE
profile dhcp-opt82
Switch to the Dhcp-opt82 profile configuration mode.
Syntax
[no] profile dhcp-opt82 <NAME>
Parameters
<NAME> - profile name. Character set from 1 to 15 symbols long.
Privilege group
config-dhcp
Command mode
CONFIG
Example
LTP-16N(configure)# profile dhcp-opt82 DHCP-PROFILE
profile pppoe-ia
Switch to the Pppoe-ia profile configuration mode.
Syntax
[no] profile pppoe-ia <NAME>
Parameters
<NAME> - profile name. Character set from 1 to 15 symbols long.
Privilege group
config-pppoe
Command mode
CONFIG
Example
LTP-16N(configure)# profile pppoe-ia PPPOE-PROFILE
system fan speed
Set fan rotation speed.
Syntax
system fan speed <VALUE>
no system fan speed
Parameters
<VALUE> - fan rotation level in percents [15-100] or automatic mode - auto.
Default value
auto
Privilege group
config-system
Command mode
CONFIG
Example
LTP-16N(configure)# system fan speed 65
system hostname
Set device name.
Syntax
system hostaname <VALUE>
no system hostname
Parameters
<VALUE> - character set from 1 to 64. It may not start or end with "-" and "_" characters.
Default value
LTP-16N
Privilege group
config-system
Command mode
CONFIG
Example
LTP-16N(configure)# system hostname test
vlan
Switch to VLAN configuration mode.
Syntax
[no] vlan <VID>
Parameters
<VID> - VLAN ID, in the range [1-4094]. Parameter can be set by a range or enumeration (For example: vlan 1-100 or vlan 100,200,300).
Default value
LTP-16N
Privilege group
config-vlan
Command mode
CONFIG
Example
LTP-16N(configure)# system hostname test