Wireless access point
WEP-12ac
User manual
Firmware version 1.19.3 (04.2020)

IP address:  http://192.168.1.10
User Name: admin
Password: password

Introduction

Annotation

Modern tendencies of telecommunication development necessitate operators to search for the most optimal technologies, allowing you to satisfy drastically growing needs of subscribers, maintaining at the same time consistency of business processes, development flexibility and reduction of costs of various services provision. Wireless technologies are spinning up more and more and have paced a huge way for short time from unstable low-speed communication networks of low radius to broadband networks equitable to speed of wired networks with high criteria to the quality of provided services. WEP-12ac device is a Wi-Fi access point of Enterprise class. Purpose: The device is dedicated to be installed inside buildings as an access point and to create a seamless wireless network using several identical access points on a large area.

This manual specifies intended purpose, main technical parameters, design, installation procedure, safe operation rules and installation recommendations for WEP-12ac.

Symbols

Notes and warnings

Device description

Purpose

WEP-12ac wireless access point (hereinafter the device) is designed for provision of users' access to high-speed safe network.

The device is dedicated to create L2 wireless networks interfacing with a wired network. WEP-12ac is connected to a wired network via 10/100/1000M Ethernet interface and arrange high-speed access to the Internet for devices supporting Wi-Fi technology at 2.4 and 5 GHz.

The device has two radio interfaces to organize two physical wireless networks.

WEP-12ac supports up-to-date requirements to service quality and allows transmitting more important traffic in higher priorities queues. Prioritization is based on main QoS technologies: CoS (special tags in VLAN packet field) and ToS (tags in IP packet field). Besides the standard methods of prioritization, the device allows you to assign demands for traffic transmission almost in every packet field from MAC to TCP/UDP port. The ACL rules and shaping allow you to control access, quality of service and restrictions for all subscribers as well as for each subscriber individually.  

WEP-12ac is designed to be installed in offices, state buildings, conference halls, laboratories, hotels, etc. The creation of virtual access points with different types of encryption allows clients to delimit access rights among users and groups of users.

Device specification

Interfaces:

• 2 Ethernet ports of 10/100/1000Base-T, 1 port out them supports PoE+ technology
• Console RJ-45;

Functions:

WLAN capabilities:

• support for IEEE 802.11a/b/g/n/ac standards;
• data aggregation, including A-MPDU (Tx /Rx) and А-MSDU (Rx);
• WMM-based priorities and packet planning;
• dynamic frequency selection (DFS);
• support for hidden SSID;
• 32 virtual access points;
• third-party access point detection;
• support for Work Group Bridge.
• WDS;
• Mesh support;
• APSD;

Network functions:

• autonegotiation of speed, duplex mode and switching between MDI and MDI-X modes;
• support for VLAN;
• authentication support 802.1X;
• support for 802.11r;
• DHCP client;
• support for IPv6;
• LLDP;
• ACL;
• SNMP;

Cluster operation mode:

• organizing a cluster with capacity of up to 64 access points;
• auto synchronization of access point configurations in a cluster;
• auto update of access points firmware in a cluster;
• Single Management IP – united address to control access points in a cluster;
• autodistribution of frequency channels among access points;
• autodistribution of output power level among access points.

QoS functions

• priority and profile-based packet scheduling;
• bandwidth limiting for each SSID;
• changing WMM parameters for each radio interface.

Security

• e-mail notifying on system events;
• centralized authorization via RADIUS server (WPA Enterprise);
• WPA/WPA2;
• Captive Portal;
• support for Internet Protocol Security (IPSec);
• support for WIDS/WIPS.

The figure below shows WEP-12ac application scheme.

Figure 1 – WEP-12ac application scheme

The device technical parameters

Table 1 – The device main technical parameters

Design

WEP-12ac enclosed in plastic case.

Device main panel

The layout of WEP-12ac is shown in the figure below.

           Figure 2 – WEP-12ac main panel layout

Connectors and controls located on the device main panel are listed in Table 2.

Table 2 – Description of ports and controls

Light indication

The current device state is displayed by Wi-Fi, LAN, Power indicators located on the front panel. The list of indicators’ possible states is given below. 

Table 3 – Light indication of device state

Reset to the default settings

In order to reset the device to factory settings, press and hold the 'F' button until «Power» indicator starts flashing. Device will be rebooted automatically. DHCP client will be launched by default. If the address is not received via DHCP the device will have IP address — 192.168.1.10, subnet mask — 255.255.255.0 and User Name/Password to access via Web interface: admin/password.

Delivery package

The delivery package includes:

• WEP-12ac wireless access point;
• Mounting kit;
• Operating manual (supplied on a CD);
• Conformity certificate;
• Technical passport.

Installation order

This section defines safety rules, installation recommendations, setup procedure and the device starting procedure.

Safety rules

Do not install the device close to heat sources or in rooms with temperature below 5 °C or above 40 °C.

Do not use the device in places with high humidity. Do not expose the device to smoke, dust, water, mechanical vibrations or shocks.

Do not open the device case. There are no user serviceable parts inside.

Installation recommendations

The recommended installation: Horizontal, on a ceiling.

Before you install and enable device, check the device for visible mechanical defects. If defects are observed, you should stop the device installation, draw up corresponding act and contact the supplier.

If the device has been exposed for a long time at a low temperature, it must be left to stand for two hours at room temperature before use. After a long stay of the device in conditions of high humidity, let it stand under normal conditions for at least 12 hours before switching on.

During the device installation to provide Wi-Fi coverage area with the best characteristics take into account the following rules:

1. Install the device at the center of a wireless network;
2. Minimize the number of obstacles (walls, roof, furniture and etc.) between WEP-2ac and other wireless network devices;
3. Do not install the device near (about 2 m) electrical and radio devices;
4. It is not recommended to use radiophone and other equipment operating on the frequency of 2.4 GHz, 5 GHz in Wi-Fi effective radius;
5. Obstacles in the form of glass/metal constructions, brick/concrete walls, water cans and mirrors can significantly reduce Wi-Fi action radius. It is not recommended to place the device inside a false ceiling as metal frame causes multipath signal propagation and signal attenuation.

During the installation of several access points, cell action radius must overlap with action radius of a neighboring cell at level of -65 ÷ -70 dBm. Decreasing of the signal level on cells borders to -75 dBm is permitted if it involves the use of VoIP, streaming video and other traffic that is sensitive to losses in wireless network.

Calculating the number of required access points

To calculate the required number of access points, you should evaluate the required coverage zone. For a more accurate assessment, it is necessary to make a radio examination of the room. Approximate radius of coverage area of WEP-12ac with a good-quality signal in case of mounting on a ceiling in typical office: 2,4 GHz — 40–50 m, 5 GHz — 20–30 m. In the absence of obstacles, the coverage radius: 2.4 GHz — up to 100 m, 5 GHz — up to 60 m.
The table below describes rough attenuation values.

Table 4 – Attenuation values

It is recommended to set nonoverlapping channels to avoid interchannel interference among neighboring access points.

Figure 3 – General diagram of frequency channel closure in the range of 2.4 GHz

For the example of channel allocation scheme among neighboring access points in frequency range of 2.4 GHz when channel width is 20 МHz, see Figure 4.

Figure 4 – Scheme of channel allocation among neighboring access points in the frequency range of 2.4 GHz when channel width is 20 MHz

Similarly, the procedure of channel allocation is recommended to save for access point allocation between floors, see Figure 5.

Figure 5 – Scheme of channel allocation between neighboring access points that are located between floors

When width of used channel is 40 MHz there is no non-overlapping channels in frequency range of 2.4 GHz. In such cases, you should select channels maximally separated from each other.

Figure 6 – Channels used in range of 5 GHz when channel width is 20, 40 or 80 MHz

Installing WEP-12ac

The device should be attached to plain surface (wall or ceiling) in accordance with the safety instruction and recommendations listed above.

The device delivery package includes required mounting kit to attach the device to plain surface.

Wall mounting

1. Fix the bracket (included in the delivery package) to the wall:

A – latch; B – channels for cables
Figure 7 – Attaching the bracket to a wall

1.1. Install the bracket in the way that the latch is on the top, see figure 7.

1.2. When installing the bracket, pass wires through the corresponding channels of the bracket, see figure 7.

1.3. Align together four boltholes on bracket and boltholes on the device surface. Screw the brackets to the device surface by using screwdrive.

2. Install the device.

Backside view                                              Front view 

Figure 8 – Device installation

2.1 Connect cables to corresponding connector of the device. Description of the connectors is given in section Design.

2.2 Align channels on the device case with the bracket and shift the device downward till fixation of the latch on the top.

Installing to false ceiling

1 – metal bracket; 2 – armstrong panel; 3 – plastic bracket; 4 – device.
Figure 9 – Mounting to a false ceiling

1. Fasten metal and plastic bracket on a ceiling as shown in the figure 9. The plastic bracket (3) should be joined with the metal one (1) on the ceiling in the following order: metal bracket -> armstrong panel -> plastic bracket.
2. Cut the hole in the armstrong panel. The size of the hole should be equal to hole of metal bracket. Conduct wires through the hole.
3. Align holes in metal bracket with holes of armstrong panel and plastic bracket. Align together four boltholes on the plastic bracket and the boltholes on the metal bracket. Screw the brackets to the device surface by using a screwdrive.
4. Install the device:

4.1. Connect cables to corresponding connector of the device. Description of the connectors is given in section Design.
4.2 Align channels on the device case with the bracket and shift the device downward till fixation of the latch on the top.

Removing the device from the bracket

To remove the device, press the latch (figure 7). Shift the device towards the latch.

Application A. WEP-12ac antenna patterns

Application B. Pin array of the device connectors

RJ-45 connector pin array

The next scheme is used for twisted-pair wiring.

RJ45-DB9 console cable pin array

RJ45-DB9 connector pin array

The example of implementation is shown on the following figure:

List of changes