Eltex Documentation EN
Быстрые ссылки
Дерево страниц
Перейти к концу метаданных
Переход к началу метаданных

clear alarms

Clear all active alarms.

Syntax
clear alarms
Parameters

The command does not contain any parameters.

Privilege group

commands-general

Command mode

ROOT

Example
LTP-16N# clear alarms

clear alarms 〈FILTER〉

Clear all alarms of the specified type.

Syntax
clear alarms <FILTER> <VALUE>
Parameters

<FILTER> — filters for alarms:

  • type — filter alarms by type. <VALUE> values are available for this filter:
    • fan — ventilation panel alarms;
    • ram — memory lack alarm;
    • load-average — CPU load alarm;
    • temperature — temperature sensors alarm;
    • pon-alarm-los — Loss of Signal pon alarm;
    • pon-alarm-losi — Loss of Signal pon alarm for ONUi;
    • pon-alarm-lofi — Loss of Frame pon alarm for ONUi;
    • pon-alarm-loami — PLOAM Loss pon alarm for ONUi;
    • pon-alarm-dowi — Drift of Window pon alarm for ONUi;
    • pon-alarm-sdi — Signal Degraded pon alarm for ONUi;
    • pon-alarm-sufi — Start-up Failure pon alarm for ONUi;
    • pon-alarm-loai — Loss of Acknowledge pon alarm for ONUi;
    • pon-alarm-dgi — Dying-Gasp pon alarm for ONUi;
    • pon-alarm-dfi — Deactivate Failure pon alarm for ONUi;
    • pon-alarm-tiwi — Transmission Interference Warning pon alarm for ONUi;
    • pon-alarm-loki — Loss of Key pon alarm for ONUi;
    • pon-alarm-lcdgi — Loss of GEM Channel Delineation pon alarm for ONUi;
    • pon-alarm-rdii — Remote Defect Indication pon alarm for ONUi;
    • login — system login alarm;
    • login — system logout alarm;
    • config-save — configuration save alarm;
    • config-change — cofiguration change alarm;
  • severity — filter alarms by importance. <VALUE> values available for this filter:
    • info;
    • minor;
    • major;
    • critical.
Privilege group

commands-general

Command mode

ROOT

Example
LTP-16N# clear alarms type fan

clear alarms history

Clear all events.

Syntax
clear alarms history
Parameters

The command does not contain any parameters.

Privilege group
commands-general
Command mode

ROOT

Example
LTP-16N# clear alarms history

clear counters interface front-port

Clear front-port interface counters.

Syntax
clear counters interface 10G-front-port <FRONT-PORT-ID>
Parameters

<FRONT-PORT-ID> —  port index in the range [1-8]. The parameter can be set by a range or enumeration (For example: interface 10-front-port 1-5 or interface gpon-port 10,12).

Privilege group

commands-interface-front-port

Command mode

ROOT

Example
LTP-16N# clear counters interface front-port 1-4

clear counters interface ont

Clear counters on the ONT interfaces.

Syntax
clear counters interface ont <PORT-ID>[/ONT-ID] <SIDE>
Parameters

<PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 or interface ont 1,3,5,7).

[ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).

<SIDE> — side on which the counters will be cleared:

  • olt-side — clear counters on the OLT side;
  • ont-side — clear counters on the ONT side.
Privilege group

commands-interface-ont

Command mode

ROOT

Example
LTP-16N# clear counters interface ont 1/1 olt-side

clear counters interface port-channel

Clear aggregated port group counters.

Syntax
clear counters interface front-port <PORT-CHANNEL-ID>
Parameters

<PORT-CHANNEL-ID> — aggregated port group index [1-32]. The parameter can be set by a range or enumeration (For example: interface port-channel 1-3 or interface port-channel 1,3,5,7).

Privilege group

commands-interface-front-port

Command mode

ROOT

Example
LTP-16N# clear counters interface port-channel 1-3

clear mac

Clear MAC table.

Syntax
clear mac
Parameters

The command does not contain any parameters.

Privilege group
config-vlan, config-igmp, config-general, config-system, config-logging, config-interface-gpon-port, config-interface-ont, config-interface-ont-profile, 
config-interface-front-port, config-access, config-cli, config-management, config-user
Command mode

ROOT

Example
LTP-16N# clear mac 
    Clearing MAC table...

    All MAC entries

clear mac interface include 〈FILTER〉

Clear MAC table by filter.

Syntax
clear mac interface include <FILTER> <VALUE>
Parameters

<FILTER> — filters for addresses to be cleared:

  • interface — clear MAC table by interface. <VALUE> values are available for this filter:
    • front-port — clear MAC addresses of the specified front-ports;
    • pon-port — clear MAC addresses of the specified pon-ports;
    • port-channel — clear MAC addresses of the specified port-channels;
    • ont — clear MAC addresses of the specified ONTs.
  • mac — clear a specific MAC address in a AA:BB:CC:DD:EE:FF format;
  • svid — clear MAC addresses by vlan. The following <VALUE> values are available for this filter: vlan index [1-4094]. The parameter can be specified as a range or an enumeration (For example: vlan 10-30 or vlan 10,40,70);
  • cvid — clear MAC addresses by vlan. The following <VALUE> values are available for this filter: vlan index [1-4094]. The parameter can be specified as a range or an enumeration (For example: vlan 10-30 or vlan 10,40,70);
  • gem — clear MAC addresses for a specified port. The following <VALUE> values are available for this filter: vlan index [0-4095].
Privilege group
  • clear mac interface: config-vlan, config-igmp, config-general, config-system, config-logging, config-interface-pon-port, config-interface-ont, config-interface-ont-profile, config-interface-front-port, config-access, config-cli, config-management, config-user;
  • clear mac vlan: view-configuration, view-firmware, config-vlan, config-igmp, config-ppoe, config-general, config-system, config-logging, config-interface-pon-port, config-interface-ont, config-interface-ont-profile, config-interface-front-port.
Command mode

ROOT

Example
LTP-16N# clear mac interface port-channel 32
    Clearing MAC table...

    10082 MAC entries

clear log files

Clear log files.

Syntax
clear log files
Parameters

The command does not contain any parameters.

Privilege group

config-system

Command mode

ROOT

Example
LTP-16N# clear log files

clear log 〈FILE_NAME〉

Clear specified log file.

Syntax
clear log <FILE_NAME>
Parameters

<FILE_NAME> – name of the log file to be cleared.

Privilege group
config-system
Command mode

ROOT

Example
LTP-16N# clear log LTP.log

clear dhcp-sessions

Clear active DHCP sessions from dhcp-snooping table.

Syntax
clear dhcp-sessions interface-ont <PORTID>/<ONT-ID>
clear dhcp-sessions interface-ont <PORTID>/<ONT-ID> <IP>
Parameters

<PORT-ID> – PON port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7);

<ONT-ID> – ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).

<IP> – IP address specified in AAA.BBB.CCC.DDD format.

Privilege group
commands-general
Command mode

ROOT

Example
LTP-16N# clear dhcp-sessions interface-ont 1

  • Нет меток