show uptime
Displays OLT operating time.
Syntax
show uptime
Parameters
The command does not contain any parameters.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show uptime up 5 min
show alarms active all
Displays all active alarms.
Syntax
show alarms active all
Parameters
The command does not contain any parameters.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms active all
Active alarms (2):
## type severity description
1 fan critical fan slot 1
2 fan critical fan slot 2
show alarms active 〈FILTER〉
Displays all active alarms by filter.
Syntax
show alarms active <FILTER> <VALUE>
Parameters
<FILTER> — filters for alarms:
- type — filter alarms by type. <VALUE> values are available for this filter:
- fan — ventilation panel alarms;
- ram — memory lack alarm;
- load-average — CPU load alarm;
- temperature — temperature sensors alarm;
- pon-alarm-los — Loss of Signal pon alarm;
- pon-alarm-losi — Loss of Signal pon alarm for ONUi;
- pon-alarm-lofi — Loss of Frame pon alarm for ONUi;
- pon-alarm-loami — PLOAM Loss pon alarm for ONUi;
- pon-alarm-dowi — Drift of Window pon alarm for ONUi;
- pon-alarm-sdi — Signal Degraded pon alarm for ONUi;
- pon-alarm-sufi — Start-up Failure pon alarm for ONUi;
- pon-alarm-loai — Loss of Acknowledge pon alarm for ONUi;
- pon-alarm-dgi — Dying-Gasp pon alarm for ONUi;
- pon-alarm-dfi — Deactivate Failure pon alarm for ONUi;
- pon-alarm-tiwi — Transmission Interference Warning pon alarm for ONUi;
- pon-alarm-loki — Loss of Key pon alarm for ONUi;
- pon-alarm-lcdgi — Loss of GEM Channel Delineation pon alarm for ONUi;
- pon-alarm-rdii — Remote Defect Indication pon alarm for ONUi;
- login — system login alarm;
- logout — system logout alarm;
- config-save — configuration save alarm;
- config-change — cofiguration change alarm;
- ont-no-config — ONUi no configuration alarm;
- ont-valid-config — ONUi-correct configuration received alarm;
- ont-state-changed — ONUi state change alarm;
- ont-link-up — ONUi link up alarm;
- ont-link-down — ONUi link down alarm;
- mac-duplicate — MAC addresses duplication alarm;
- severity — filter alarms by importance. <VALUE> values are available for this filter:
- info;
- minor;
- major;
- critical.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms active type fan
Active alarms (2):
## type severity description
1 fan critical fan slot 1
2 fan critical fan slot 2
LTP-16N# show alarms active severity info
No alarms.
LTP-16N# show alarms active severity critical
Active alarms (2):
## type severity description
1 fan critical fan slot 1
2 fan critical fan slot 2
show alarms history all
Displays all alarms.
Syntax
show alarms history all
Parameters
The command does not contain any parameters.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms history all
Datetime Severity Type Norm Description
------------------- -------- ------------------ ---- ----------------------
13.05.2022 08:18:01 info fan Fan 1 speed 6360 rpm
13.05.2022 08:18:31 info fan * Fan 1 speed 6540 rpm is back to
normal
13.05.2022 08:19:54 major ont-link-up ONT6/2 (ELTX660421C4) link up
13.05.2022 08:19:59 info ont-state-changed ELTX660421C4 6 2 OK
"NTU-RG-1421G-Wac" "3.40.1.1655"
"2v6" "-19.83"
show alarms history all ordering time 〈FILTER〉
Displays all alarms by time.
Syntax
show alarms history all ordering time <FILTER>
Parameters
<FILTER> — filters for alarms:
- desc — filter alarms by time and description;
- none — filter alarms by time.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms history all ordering time Datetime Severity Type Norm Description ------------------- -------- ------------------ ---- --------------------------------- 01.06.2022 03:07:04 info ont-link-down ONT12/10 (ELTX5C009600) link down 01.06.2022 03:07:04 info ont-link-down ONT12/19 (ELTX5C000FB4) link down 01.06.2022 03:07:04 info ont-link-down ONT12/11 (ELTX5C0E0AC4) link down
show alarms history all ordering type <FILTER〉
Displays all alarms by filter type.
Syntax
show alarms history all ordering type <FILTER>
Parameters
<FILTER> — filters for alarms:
- desc — filter alarms by time and description;
- none — filter alarms by time.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms history all ordering type fan Datetime Severity Type Norm Description ------------------- -------- ------- ---- -------------------------------------- 13.05.2022 08:18:01 info fan Fan 1 speed 6360 rpm 13.05.2022 08:18:31 info fan * Fan 1 speed 6540 rpm is back to normal
show alarms history all ordering severity 〈FILTER〉
Displays all active alarms by severity.
Syntax
show alarms history all ordering severity <FILTER>
Parameters
<FILTER> — filters for alarms:
- desc — filter alarms by time and description;
- none — filter alarms by time.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms history all ordering severity info Datetime Severity Type Norm Description ------------------- -------- ----- ---- -------------------------------------- 13.05.2022 08:18:01 info fan Fan 1 speed 6360 rpm 13.05.2022 08:18:31 info fan * Fan 1 speed 6540 rpm is back to normal 13.05.2022 08:18:31 info ont-link-up ONT3/103 (ELTX1A00FA56) link up
show alarms history 〈FILTER〉
Displays all active alarms by filter.
Syntax
show alarms history <FILTER> <VALUE>
Parameters
<FILTER> – alarms filters:
- type — filter alarms by type. <VALUE> values are available for this filter:
- fan — ventilation panel alarms;
- ram — memory lack alarm;
- load-average — CPU load alarm;
- temperature — temperature sensors alarm;
- pon-alarm-los — Loss of Signal pon alarm;
- pon-alarm-losi — Loss of Signal pon alarm for ONUi;
- pon-alarm-lofi — Loss of Frame pon alarm for ONUi;
- pon-alarm-loami — PLOAM Loss pon alarm for ONUi;
- pon-alarm-dowi — Drift of Window pon alarm for ONUi;
- pon-alarm-sdi — Signal Degraded pon alarm for ONUi;
- pon-alarm-sufi — Start-up Failure pon alarm for ONUi;
- pon-alarm-loai — Loss of Acknowledge pon alarm for ONUi;
- pon-alarm-dgi — Dying-Gasp pon alarm for ONUi;
- pon-alarm-dfi — Deactivate Failure pon alarm for ONUi;
- pon-alarm-tiwi — Transmission Interference Warning pon alarm for ONUi;
- pon-alarm-loki — Loss of Key pon alarm for ONUi;
- pon-alarm-lcdgi — Loss of GEM Channel Delineation pon alarm for ONUi;
- pon-alarm-rdii — Remote Defect Indication pon alarm for ONUi;
- login — system login alarm;
- logout — system logout alarm;
- config-save — configuration save alarm;
- config-change — cofiguration change alarm;
- ont-no-config — ONUi no configuration alarm;
- ont-valid-config — ONUi-correct configuration received alarm;
- ont-state-changed — ONUi state change alarm;
- ont-link-up — ONUi link up alarm;
- ont-link-down — ONUi link down alarm;
- mac-duplicate — MAC addresses duplication alarm;
- severity – filter alarms by importance. <VALUE> values are available for this filter:
- info;
- minor;
- major;
- critical.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms history type fan Datetime Severity Type Norm Description ------------------- -------- ------------ ---- -------------------------------------- 13.05.2022 08:18:01 info fan Fan 1 speed 6360 rpm 13.05.2022 08:18:31 info fan * Fan 1 speed 6540 rpm is back to normal LTP-16N# show alarms history severity info Datetime Severity Type Norm Description ------------------- -------- ------------- ---- -------------------------------------- 13.05.2022 08:18:01 info fan Fan 1 speed 6360 rpm 13.05.2022 08:18:31 info fan * Fan 1 speed 6540 rpm is back to normal LTP-16N# show alarms history severity critical Datetime Severity Type Norm Description ------------------- -------- ------------- ---- -------------------------------- 13.05.2022 08:20:45 critical ont-link-down ONT6/2 (ELTX660421C4) link down 13.05.2022 08:23:32 critical ont-link-down ONT6/2 (ELTX660421C4) link down
show alarms history alarm
Displays all alarms excluding normalizing ones.
Syntax
show alarms history all
Parameters
The command does not contain any parameters.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms history alarm
Datetime Severity Type Norm Description
------------------- -------- ------------------ ---- ------------------------------
13.05.2022 08:18:01 info fan Fan 1 speed 6360 rpm
13.05.2022 08:18:31 info fan * Fan 1 speed 6540 rpm is back to
normal
13.05.2022 08:19:54 major ont-link-up ONT6/2 (ELTX660421C4) link up
13.05.2022 08:19:59 info ont-state-changed ELTX660421C4 6 2 OK "NTU-RG-1421G-
Wac" "3.40.1.1655" "2v6" "-19.83"
show alarms history alarm ordering time 〈FILTER〉
Displays all alarms by time excluding normalizing ones.
Syntax
show alarms history alarm ordering time <FILTER>
Parameters
<FILTER> — filters for alarms:
- desc — filter alarms by time and description;
- none — filter alarms by time.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms history alarm ordering time Datetime Severity Type Norm Description ------------------- -------- ------------- ---- --------------------------------- 01.06.2022 03:07:04 info ont-link-down ONT12/10 (ELTX5C009600) link down 01.06.2022 03:07:04 info ont-link-down ONT12/19 (ELTX5C000FB4) link down 01.06.2022 03:07:04 info ont-link-down ONT12/11 (ELTX5C0E0AC4) link down
show alarms history alarm ordering type 〈FILTER〉
Displays all alarms by filter excluding normalizing ones.
Syntax
show alarms history alarm ordering type <FILTER>
Parameters
<FILTER> — filters for alarms:
- desc — filter alarms by time and description;
- none — filter alarms by time.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms history alarm ordering type fan Datetime Severity Type Norm Description ------------------- -------- ------- ----- -------------------------------------- 13.05.2022 08:18:01 info fan Fan 1 speed 6360 rpm 13.05.2022 08:18:31 info fan * Fan 1 speed 6540 rpm is back to normal
show alarms history normalized-alarm
Displays all normalizing alarms.
Syntax
show alarms history normalized-alarm
Parameters
The command does not contain any parameters.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms history normalized-alarm
Datetime Severity Type Norm Description
------------------- -------- ------------- ----- ----------------------------------
02.06.2022 04:00:08 critical load-average * CPU load average (1m, 5m, 15m):
2.79, 2.32, 1.64 is back to normal
02.06.2022 04:07:38 critical load-average * CPU load average (1m, 5m, 15m):
2.98, 2.43, 1.92 is back to normal
show alarms history normalized-alarm ordering time 〈FILTER〉
Displays all normalizing alarms by time.
Syntax
show alarms history normalized-alarm ordering time <FILTER>
Parameters
<FILTER> — filters for alarms:
- desc — filter alarms by time and description;
- none — filter alarms by time.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms history normalized-alarm ordering time
Datetime Severity Type Norm Description
------------------- -------- ------------------ ---- ----------------------------------
02.06.2022 04:00:08 critical load-average * CPU load average (1m, 5m, 15m):
2.79, 2.32, 1.64 is back to normal
02.06.2022 04:07:38 critical load-average * CPU load average (1m, 5m, 15m):
2.98, 2.43, 1.92 is back to normal
show alarms history normalized-alarm ordering type 〈FILTER〉
Displays all normalizing alarms by filter.
Syntax
show alarms history normalized-alarm ordering type <FILTER>
Parameters
<FILTER> — filters for alarms:
- desc — filter alarms by time and description;
- none — filter alarms by time.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms history normalized-alarm ordering type ram Datetime Severity Type Norm Description ------------------- -------- ------------------ ---- --------------------------------- 09.06.2022 03:42:44 info ram * Free RAM is 81% is back to normal 09.06.2022 03:43:14 info ram * Free RAM is 80% is back to normal
show alarms history normalized-alarm ordering severity 〈FILTER〉
Displays all normalizing alarms by severity.
Syntax
show alarms history normalized-alarm ordering severity <FILTER>
Parameters
<FILTER> — filters for alarms:
- desc — filter alarms by time and description;
- none — filter alarms by time.
Privilege group
view-general
Command mode
ROOT
Example
LTP-16N# show alarms history normalized-alarm ordering severity
Datetime Severity Type Norm Description
------------------- -------- ------------------ ---- ---------------------------------
09.06.2022 03:42:34 info temperature * Sensor PON SFP 1 temperature 30C
is back to normal
09.06.2022 03:42:34 info temperature * Sensor PON SFP 2 temperature 29C
is back to normal
show candidate-config
Displayss the current candidate configuration. Displays a list of all nonapplied changes in a given session relative to the current configuration.
Syntax
show candidate-config
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config
configure terminal
management ip 192.168.1.3
exit
commit
exit
show candidate-config alarm
Displays the candidate configuration for alarms.
Syntax
show candidate-config alarm
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config alarm
alarm
system-temperature sensor pon-ports-1 max 60
system-temperature sensor pon-ports-2 max 60
show candidate-config cli
Displays the candidate configuration for CLI.
Syntax
show candidate-config cli
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config cli cli max-sessions 4
show candidate-config interface front-port
Displays the candidate configuration for front-port.
Syntax
show candidate-config interface front-port <PORT-ID>
Parameters
<PORT-ID> — port index in the range [1-8]. The parameter can be set by a range or enumeration (for example: interface front-port 1-5 or interface front-port 1,5).
Privilege group
view-configuration, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show candidate-config interface front-port 1
interface front-port 1
vlan allow 1000
exit
show candidate-config interface pon-port
Displays running configuration for pon-port.
Syntax
show candidate-config interface pon-port <PORT-ID>
Parameters
<PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface pon-port 1-3 or interface pon-port 1,3,5,7).
Privilege group
view-configuration, config-interface-pon-port
Command mode
ROOT
Example
LTP-16N# show candidate-config interface pon-port 15,16
interface pon-port 15
shutdown
exit
interface pon-port 16
shutdown
exit
show candidate-config interface ont
Display the candidate configuration for ONT.
Syntax
show candidate-config interface ont <PORT-ID>[/ONT-ID]
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-configuration, config-interface-ont
Command mode
ROOT
Example
LTP-16N# show candidate-config interface ont 1/1
interface ont 1/1
service 1 profile cross-connect "HSI" dba "DBA"
exit
show candidate-config ip dhcp
Displays candidate configuration for DHCP.
Syntax
show candidate-config ip dhcp
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config ip dhcp
ip dhcp
snooping enable
exit
show candidate-config ip igmp
Display candidate configuration for IGMP.
Syntax
show candidate-config ip igmp
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config ip igmp ip igmp snooping
show candidate-config ip pppoe
Display candidate configuration for PPPoE.
Syntax
show candidate-config ip pppoe
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config ip pppoe
ip pppoe
snooping enable
exit
show candidate-config ip snmp
Displays candidate configuration for SNMP.
Syntax
show candidate-config ip snmp
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config ip snmp ip snmp contact Eltex
show candidate-config ip ssh
Displays candidate configuration for SSH.
Syntax
show candidate-config ip ssh
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config ip ssh no ip ssh enable
show candidate-config ip telnet
Displays candidate configuration for TELNET.
Syntax
show candidate-config ip telnet
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config ip telnet no ip telnet enable
show candidate-config ip ntp
Displays candidate configuration for NTP.
Syntax
show candidate-config ip ntp
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config ip ntp ip ntp enable
show candidate-config pon
Displays candidate configuration for pon network settings.
Syntax
show candidate-config pon
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config pon pon network svlan-ethertype 802.1ad
show candidate-config port-channel
Displays candidate configuration for port-channel.
Syntax
show candidate-config interface port-channel <PORT-CHANNEL-ID>
Parameters
<PORT-CHANNEL-ID> — ID of port-channel. The parameter can be set by a range or enumeration (For example: interface port-channel 1-5 or interface interface port-channel 1,5).
Privilege group
view-configuration, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show candidate-config interface port-channel 1-2
interface port-channel 1
vlan allow 20,99
exit
interface port-channel 2
vlan allow 30
exit
show candidate-config port-channel load-balance
Displays candidate configuration for port-channel load-balance.
Syntax
show candidate-config interface port-channel load-balance
Parameters
The command does not contain any parameters.
Privilege group
view-configuration, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show candidate-config interface port-channel load-balance interface port-channel load-balance hash src-mac dst-mac interface port-channel load-balance polynomial 0x84a1
show candidate-config logging
Displays candidate configuration for logging.
Syntax
show candidate-config logging
Parameters
The command does not contain any parameters.
Privilege group
view-configuration, config-logging
Command mode
ROOT
Example
LTP-16N# show candidate-config logging
logging
module dna interface ont 1/1 loglevel debug
exit
show candidate-config lldp
Displays candidate configuration for LLDP.
Syntax
show candidate-config lldp
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config lldp no lldp enable
show candidate-config management
Displays candidate configuration of network management settings.
Syntax
show candidate-config management
Parameters
The command does not contain any parameters.
Privilege group
view-configuration, config-management
Command mode
ROOT
Example
LTP-16N# show candidate-config management management ip 192.168.1.100 management gateway 192.168.1.1 management vid 100
show candidate-config privilege
Displays candidate configuration for privileges.
Syntax
show candidate-config privilege
Parameters
The command does not contain any parameters.
Privilege group
view-configuration, config-user
Command mode
ROOT
Example
LTP-16N# show candidate-config privilege privilege 3 view-system
show candidate-config profile cross-connect
Displays candidate configuration for cross-connect profile.
Syntax
show candidate-config profile cross-connect [NAME]
Parameters
[NAME] — profile name. A set of characters from 1 to 15 in length.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show candidate-config profile cross-connect HSI
profile cross-connect HSI
bridge enable
bridge group 10
outer vid 100
exit
show candidate-config profile dba
Displays candidate configuration for DBA profile.
Syntax
show candidate-config profile dba [NAME]
Parameters
[NAME] — profile name. A set of characters from 1 to 15 in length.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show candidate-config profile dba DBA
profile dba DBA
mode status-reporting
exit
show candidate-config profile ports
Displays candidate configuration for ports profile.
Syntax
show candidate-config profile ports [NAME]
Parameters
[NAME] — profile name. A set of characters from 1 to 15 in length.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show candidate-config profile ports
profile ports pp
port 1 bridge group 10
exit
show candidate-config profile management
Displays candidate configuration for management interface profile.
Syntax
show candidate-config profile management [NAME]
Parameters
[NAME] — profile name. A set of characters from 1 to 15 in length.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show candidate-config profile management
profile management MANAGEMENT
iphost id 3
exit
show candidate-config profile dhcp-opt82
Displays candidate configuration for dhcp-opt82 profile.
Syntax
show candidate-config profile dhcp-opt82 [NAME]
Parameters
[NAME] — profile name. A set of characters from 1 to 15 in length.
Privilege group
view-configuration, config-dhcp
Command mode
ROOT
Example
LTP-16N# show candidate-config profile dhcp-opt82
profile dhcp-opt82 DHCP-82
ont-sn-format numerical
exit
show candidate-config profile pppoe-ia
Displays candidate configuration for pppoe-ai profile.
Syntax
show candidate-config profile pppoe-ia [NAME]
Parameters
[NAME] — profile name. A set of characters from 1 to 15 in length.
Privilege group
view-configuration, config-pppoe
Command mode
ROOT
Example
LTP-16N# show candidate-config profile pppoe-ia
profile pppoe-ia PPPOE
ont-sn-format numerical
exit
show candidate-config qos
Displays candidate configuration of QoS.
Syntax
show candidate-config qos
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config qos qos enable
show candidate-config system
Displays candidate of system configuration.
Syntax
show candidate-config system
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config system system fan speed 100
show candidate-config user
Displays candidate configuration for users.
Syntax
show candidate-config user
Parameters
The command does not contain any parameters.
Privilege group
view-configuration, config-user
Command mode
ROOT
Example
LTP-16N# show candidate-config user user test2 encrypted_password $6$XqyNfsV/$h.QgxTKh9PFGvO5nZ5jSuZqOC4Z274lDbSktK51YX8xmmsFUk9FmIUSqZDC7SOmVAtH3XBIR5bOYY5tra4T8j1 user test2 privilege 0
show candidate-config vlan
Displays candidate configuration for VLAN.
Syntax
show candidate-config vlan <VID>
Parameters
<VID> — VLAN ID, in the range [1-4094].
Privilege group
view-configuration, config-vlan
Command mode
ROOT
Example
LTP-16N# show candidate-config vlan 100
vlan 100
ip igmp snooping enable
exit
show candidate-config lldp
Displays candidate configuration of LLDP.
Syntax
show candidate-config lldp
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show candidate-config lldp lldp enable
show date
Displays current date.
Syntax
show date
Parameters
The command does not contain any parameters.
Privilege group
view-systemCommand mode
ROOT
Example
LTP-16N# show date Tue Sep 8 08:32:53 UTC 2020
show firmware
Display the list of firmware in main and redundant areas. The select field marks which firmware will be loaded after rebooting. To upload firmware to the device use the copy command.
Syntax
show firmware
Parameters
The command does not contain any parameters.
Privilege group
view-firmware
Command mode
ROOT
Example
LTP-16N# show firmware
Select Type Version Build Date
------ ------ -------- ----- ----------------
* master 1.2.0 472 19.05.2021 09:18
-----------------------------------------------------
slave 1.2.0 467 17.05.2021 06:53
"*" designates that the image was selected for the next boot
LTP-16N#
show firmware ont list
Displays the list of firmware for ONT uploaded to the device. To upload firmware to the device use the copy command.
Syntax
show firmware ont list
Parameters
The command does not contain any parameters.
Privilege group
view-firmware
Command mode
ROOT
Example
LTP-16N# show firmware ont list N | Firmware ---------------------------- 1 | ntu-1-3.28.0-build645.fw.bin ---------------------------- 2 | ntu-1-3.26.5.101.fw.bin ---------------------------- 3 | ntu-2-3.28.0.2387.fw.bin ---------------------------- 4 | ntu-rg-54xx-1.3.0.825.fw.bin ---------------------------- 5 | ntu-1-3.28.0-build648.fw.bin
show interface front-port 〈PORT-ID〉 counters
Displays counters on front ports.
Syntax
show interface front-port <PORT-ID> counters
Parameters
<PORT-ID> — port index in the range [1-8]. The parameter can be set by a range or enumeration (For example: interface front-port 1-5 or interface front-port 1,5).
Privilege group
view-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface front-port 3 counters Port UC packet recv MC packet recv BC packet recv Octets recv UC packet sent MC packet sent BC packet sent Octets sent --- ---------- --------- -------- ------ -------- ------- -------- ------- 3 0 0 0 0 0 0 0 0
show interface front-port 〈PORT-ID〉 counters verbose
Displays counters on front ports in details.
Syntax
show interface front-port <PORT-ID> counters
Parameters
<PORT-ID> — port index in the range [1-8]. The parameter can be set by a range or enumeration (for example: interface front-port 1-5 or interface front-port 1,5).
Privilege group
view-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface front-port 8 counters verbose front-port 8 statistics Rx Bytes 3853048381 Rx Packets 2841701 Rx Unicast Packets 22085 Rx Multicast Packets 2819615 Rx Broadcast Packets 1 Rx Error Packets 0 Rx Unknown Proto Packets 0 Tx Bytes 2299253 Tx Packets 21890 Tx Unicast Packets 21831 Tx Multicast Packets 54 Tx Broadcast Packets 5 Tx Error Packets 0 Rx frames 64 526 Rx frames 65-127 22172 Rx frames 128-255 39 Rx frames 256-511 0 Rx frames 512-1023 0 Rx frames 1024-1518 2818965 Rx frames 1519-2047 0 Rx frames 2048-4095 0 Rx frames 4096-9216 0 Rx frames 9217-16383 0 Tx frames 64 2 Tx frames 65-127 21871 Tx frames 128-255 17 Tx frames 256-511 0 Tx frames 512-1023 0 Tx frames 1024-1518 0 Tx frames 1519-2047 0 Tx frames 2048-4095 0 Tx frames 4096-9216 0 Tx frames 9217-16383 0
show interface front-port 〈PORT-ID〉 state
Displays front ports state.
Syntax
show interface front-port <PORT-ID> state
Parameters
<PORT-ID> — port index in the range [1-8]. The parameter can be set by a range or enumeration (for example: interface front-port 1-5 or interface front-port 1,5).
Privilege group
view-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface front-port 1 state
Front-port Status Speed Media
-------------------- -------------------- -------------------- --------------------
1 up 1G copper
show interface front-port 〈PORT-ID〉 utilization
Displays utilization by front ports.
Syntax
show interface front-port <PORT-ID> utilization
Parameters
<PORT-ID> — port index in the range [1-8]. The parameter can be set by a range or enumeration (for example: interface front-port 1-5 or interface front-port 1,5).
Privilege group
view-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface front-port 3 utilization 1 minute utilization average Port Tx Kbits/sec Rx Kbits/sec Tx Frames/sec Rx Frames/sec ---- ------------ ------------ ------------- ------------- 3 0 16 0 20 5 minute utilization average Port Tx Kbits/sec Rx Kbits/sec Tx Frames/sec Rx Frames/sec ---- ------------ ------------ ------------- ------------- 3 0 15 0 19
show interface ont 〈PORT-ID〉 [/ONT-ID] online
Displays the list of configured and online ONTs.
Syntax
show interface ont <PORT-ID>[/ONT-ID] online
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1 online
-----------------------------------
PON-port 1 ONT online list
-----------------------------------
## Serial ONT ID PON-port RSSI Status
1 ELTX6C000090 1 1 -19.96 OK
show interface ont 〈PORT-ID〉 [/ONT-ID] offline
Displays the list of configured and offline ONTs.
Syntax
show interface ont <PORT-ID>[/ONT-ID] offline
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 или interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1 offline
-----------------------------------
pon-port 1 ONT offline list
-----------------------------------
## Serial ONT ID pon-port Status
1 ELTX6C000090 1 1 OFFLINE
show interface ont 〈PORT-ID〉 [/ONT-ID] unactivated
Displays the list of configured and offline ONTs.
Syntax
show interface ont <PORT-ID>[/ONT-ID] unactivated
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128].The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 unactivated
-----------------------------------
PON-port 1 ONT unactivated list
-----------------------------------
## Serial ONT ID PON-port RSSI Version EquipmentID Status
1 ELTX0600003D n/a 1 n/a n/a n/a UNACTIVATED
show interface ont 〈PORT-ID〉 [/ONT-ID] configured
Displays the list of configured ONTs.
Syntax
show interface ont <PORT-ID>[/ONT-ID] configured
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 configured
-----------------------------------
PON-port 1 ONT configured list
-----------------------------------
## Serial ONT ID PON-port Status
1 ELTX6C000090 1 1 OK
show interface ont 〈PORT-ID〉 [/ONT-ID] unconfigured
Displays the list of free indexes on the port.
Syntax
show interface ont <PORT-ID>[/ONT-ID] unconfigured
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 3 unconfigured
PON-port 3 ONT unconfigured: 1-128
show interface ont 〈PORT-ID〉 [/ONT-ID] connected
Displays the list of unactivated and online ONTs.
Syntax
show interface ont <PORT-ID>[/ONT-ID] connected
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 connected
-----------------------------------
pon-port 1 ONT connected list
-----------------------------------
## Serial ONT ID PON-port RSSI Version EquipmentID Status
1 ELTX0600003D 1 1 -7.44 3.25.1.11 NTP-RG-1402G OK
show interface ont 〈PORT-ID〉 [/ONT-ID] counters pon
Displays PON counters for ONT on the OLT side.
Синтаксис
show interface ont <PORT-ID>[/ONT-ID] counters pon
Параметры
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters pon
[ONT 1/1] PON statistics
Drift Positive: 0
Drift Negative: 0
Delimiter Miss Detection: 0
BIP Errors: 0
BIP Units: 104238772192
FEC Corrected symbols: 0
FEC Codewords Uncorrected: 0
FEC Codewords Uncorrected: 0
FEC Codewords: 0
FEC Corrected Units: 0
Rx PLOAMs Errors: 0
Rx PLOAMs Non Idle: 15
Rx OMCI: 405
Rx OMCI Packets CRC Error: 0
Rx Bytes: 40262
Rx Packets: 542
Tx Bytes: 19296
Tx Packets: 402
BER Reported: 0
show interface ont 〈PORT-ID〉 [/ONT-ID] counters gem-port
Displays GEM port counters for ONT on the OLT side.
Syntax
show interface ont <PORT-ID>[/ONT-ID] counters gem-port
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters gem-port
ONT [1/1] GEM port statistics
GEM port id Rx Packet Rx Bytes Tx Packet Tx Bytes
129 135 20642 0 0
Broadcast 0 0 0 0
Multicast 0 0 13153 17964394
show interface ont 〈PORT-ID〉 [/ONT-ID] rssi
Displays the signal power level.
Syntax
show interface ont <PORT-ID>[/ONT-ID] rssi
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 rssi ----------------------------------- [ONT1/1] RSSI ----------------------------------- Received signal strength indication: -19.913998 [dBm]
show interface ont 〈PORT-ID〉 [/ONT-ID] data-path
Displays the configuration for this ONT.
Syntax
show interface ont <PORT-ID>[/ONT-ID] data-path
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 data-path
Service #1:
outer vid 100
inner vid 1
user vid: -1
replace: ont-side
bridge_group: 10
t-cont id: 0
alloc id: 767
gem port: 129
flow id: 11269
traffic model: N_TO_1
front-port: 3
Bridge #1:
service profile id: 0
broadcast enable: true
broadcast filters: 100 0 0 0 0 0 0 0 0 0 0 0
multicast enable: false
multicast filters: 0 0 0 0 0 0 0 0 0 0 0 0
Port #1:
bridge group: 0
multicast enable: false
Port #2:
bridge group: 0
multicast enable: false
Port #3:
bridge group: 0
multicast enable: false
Port #4:
bridge group: 0
multicast enable: false
Virtual ethernet interface pointer:
bridge group: 0
vlan operation #1:
user vid: 100
replace: ont-side
multicast enable: false
Alloc base #1:
scheme: share-t-cont
alloc ids: 767
show interface ont 〈PORT-ID〉 [/ONT-ID] counters olt-side pon
Displays pon counters on the olt-side
Syntax
show interface ont <PORT-ID>[/ONT-ID] counters olt-side pon
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters olt-side pon ----------------------------------- [ONT 1/1] PON statistics ----------------------------------- Drift Positive: 0 Drift Negative: 0 Delimiter Miss Detection: 0 BIP Errors: 0 BIP Units: 103150550416 FEC Corrected symbols: 0 FEC Codewords Uncorrected: 0 FEC Codewords Corrected: 0 FEC Codewords: 0 FEC Corrected Units: 0 Rx PLOAMs Errors: 0 Rx PLOAMs Non Idle: 29 Rx OMCI: 447 Rx OMCI Packets CRC Error: 0 Rx Bytes: 21456 Rx Packets: 447 Tx Bytes: 21312 Tx Packets: 444 BER Reported: 0
show interface ont 〈PORT-ID〉 [/ONT-ID] counters olt-side gem-port
Отображение счетчиков по gem-портам на olt-side
Syntax
show interface ont <PORT-ID>[/ONT-ID] counters olt-side gem-port
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters olt-side gem-port ----------------------------------- [ONT 1/1] GEM port statistics ----------------------------------- GEM port id Rx Packet Rx Bytes Tx Packet Tx Bytes ----------- -------------------- -------------------- -------------------- -------------------- 128 0 0 0 0 Broadcast 0 0 49 12068 Multicast 0 0 297 19008
show interface ont 〈PORT-ID〉 [/ONT-ID] counters ont-side gem-port-performance-monitoring
Displays gem-port-performance-monitoring counters (ME class 267)
Syntax
show interface ont <PORT-ID>[/ONT-ID] counters ont-side gem-port-performance-monitoring
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters ont-side gem-port-performance-monitoring
show interface ont 〈PORT-ID〉 [/ONT-ID] counters ont-side gem-port-nctp-performance-monitoring
Displays gem-port-nctp-performance-monitoring counters (ME class 341)
Syntax
show interface ont <PORT-ID>[/ONT-ID] counters ont-side gem-port-nctp-performance-monitoring
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters ont-side gem-nctp-port-performance-monitoring ----------------------------------- [ONT 1/1] counters ----------------------------------- ## Downstream counters for gem: service 1 BC -- ---------------------------- -------------------- -------------------- 1 Finished intervals 104 104 2 Received GEM frames 0 4 3 Received payload bytes 0 1106 ## Upstream counters for gem: service 1 BC -- ---------------------------- -------------------- -------------------- 1 Finished intervals 104 104 2 Transmitted GEM frames 0 0 3 Transmitted payload bytes 0 0
show interface ont 〈PORT-ID〉 [/ONT-ID] counters ont-side ethernet-performance-monitoring-history-data
Displays ethernet-performance-monitoring-history-data counters (ME class 24).
Syntax
show interface ont <PORT-ID>[/ONT-ID] counters ont-side ethernet-performance-monitoring-history-data
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters ont-side ethernet-performance-monitoring-history-data ----------------------------------- [ONT 1/1] counters ----------------------------------- ## Counters for ports: 1 2 3 4 --- ----------------------------------- ---------- ---------- ---------- ---------- 1 Finished intervals 105 105 105 105 2 FCS errors 0 0 0 0 3 Excessive collision counter 0 0 0 0 4 Late collision counter 0 0 0 0 5 Frames too long 0 0 0 0 6 Buffer overflow on receive 0 0 0 0 7 Buffer overflow on transmit 0 0 0 0 8 Single collision frame counter 0 0 0 0 9 Multiple collisions frame counter 0 0 0 0 10 SQE counter 0 0 0 0 11 Deferred transmission counter 0 0 0 0 12 Internal MAC transmit error counter 0 0 0 0 13 Carrier sense error counter 0 0 0 0 14 Alignment error counter 0 0 0 0 15 Internal MAC receive error counter 0 0 0 0
show interface ont 〈PORT-ID〉 [/ONT-ID] counters ont-side ethernet-performance-monitoring-history-data2
Displays ethernet-performance-monitoring-history-data2 counters (ME class 89).
Syntax
show interface ont <PORT-ID>[/ONT-ID] counters ont-side ethernet-performance-monitoring-history-data2
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters ont-side ethernet-performance-monitoring-history-data2
show interface ont 〈PORT-ID〉 [/ONT-ID] counters ont-side ethernet-performance-monitoring-history-data3
Displays ethernet-performance-monitoring-history-data3 counters (ME class 296).
Syntax
show interface ont <PORT-ID>[/ONT-ID] counters ont-side ethernet-performance-monitoring-history-data3
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters ont-side ethernet-performance-monitoring-history-data3 ----------------------------------- [ONT 1/1] counters ----------------------------------- ## Counters for ports: 1 2 3 4 --- --------------------------- ---------- ---------- ---------- ---------- 1 Finished intervals 105 105 105 105 2 Drop events 0 0 0 0 3 Octets 960 0 0 0 4 Packets 15 0 0 0 5 Broadcast packets 0 0 0 0 6 Multicast packets 15 0 0 0 7 Undersize packets 0 0 0 0 8 Fragments 0 0 0 0 9 Jabbers 0 0 0 0 10 Packets 64 octets 15 0 0 0 11 Packets 65 to 127 octets 0 0 0 0 12 Packets 128 to 255 octets 0 0 0 0 13 Packets 256 to 511 octets 0 0 0 0 14 Packets 512 to 1023 octets 0 0 0 0 15 Packets 1024 to 1518 octets 0 0 0 0
show interface ont 〈PORT-ID〉 [/ONT-ID] counters ont-side gal-ethernet-performance-monitoring-history-data
Displays gal-ethernet-performance-monitoring-history-data counters (ME class 276)
Syntax
show interface ont <PORT-ID>[/ONT-ID] counters ont-side gal-ethernet-performance-monitoring-history-data
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters ont-side gal-ethernet-performance-monitoring-history-data [ONT 1/1] counters ## Counters for gal: service 1 BC -- ------------------ -------------------- -------------------- 1 Finished intervals 105 105 2 Discarded frames 0 0
show interface ont 〈PORT-ID〉 [/ONT-ID] counters ont-side fec-performance-monitoring-history-data
Displays fec-performance-monitoring-history-data counters (ME class 312)
Syntax
show interface ont <PORT-ID>[/ONT-ID] counters ont-side fec-performance-monitoring-history-data
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters ont-side fec-performance-monitoring-history-data
show interface ont 〈PORT-ID〉 [/ONT-ID] counters ont-side ethernet-frame-extended-performance-monitoring
Displays ethernet-frame-extended-performance-monitoring counters (ME class 334)
Syntax
show interface ont <PORT-ID>[/ONT-ID] counters ont-side ethernet-frame-extended-performance-monitoring
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters ont-side ethernet-frame-extended-performance-monitoring ----------------------------------- [ONT 1/1] counters ----------------------------------- ## Upstream counters for ports: 1 2 3 4 --- ------------------------------- ---------- ---------- ---------- ---------- 1 Finished intervals 0 0 0 0 2 Drop events 0 0 0 0 3 Octets 17344 0 0 0 4 Frames 271 0 0 0 5 Broadcast frames 0 0 0 0 6 Multicast frames 271 0 0 0 7 CRC errored frames 0 0 0 0 8 Undersize frames 0 0 0 0 9 Oversize frames 0 0 0 0 10 Frames 64 octets 271 0 0 0 11 Frames 65 to 127 octets 0 0 0 0 12 Frames 128 to 255 octets 0 0 0 0 13 Frames 256 to 511 octets 0 0 0 0 14 Frames 512 to 1023 octets 0 0 0 0 15 Frames 1024 to 1518 octets 0 0 0 0 ## Downstream counters for ports: 1 2 3 4 --- ------------------------------- ---------- ---------- ---------- ---------- 1 Finished intervals 0 0 0 0 2 Drop events 0 0 0 0 3 Octets 8384 0 0 0 4 Frames 131 0 0 0 5 Broadcast frames 0 0 0 0 6 Multicast frames 131 0 0 0 7 CRC errored frames 0 0 0 0 8 Undersize frames 0 0 0 0 9 Oversize frames 0 0 0 0 10 Frames 64 octets 131 0 0 0 11 Frames 65 to 127 octets 0 0 0 0 12 Frames 128 to 255 octets 0 0 0 0 13 Frames 256 to 511 octets 0 0 0 0 14 Frames 512 to 1023 octets 0 0 0 0 15 Frames 1024 to 1518 octets 0 0 0 0
show interface ont 〈PORT-ID〉 [/ONT-ID] counters ont-side multicast-subscriber-monitor
Displays multicast-subscriber-monitor counters (ME class 311)
Syntax
show interface ont <PORT-ID>[/ONT-ID] counters ont-side multicast-subscriber-monitor
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (for example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 1/1 counters ont-side multicast-subscriber-monitor
show interface port-channel 〈PORT-CHANNEL-ID〉 counters
Displays counters by port-channels
Syntax
show interface port-channel <PORT-CHANNEL-ID> counters
Parameters
<PORT-CHANNEL-ID> — ID of port-channel. The parameter can be a range or an enumeration (e.g.: interface interface port-channel 1-5 or interface interface interface port-channel 1,5).
Privilege group
view-interface-front-port, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface port-channel 1 counters Port UC packet recv MC packet recv BC packet recv Octets recv UC packet sent MC packet sent BC packet sent Octets sent --- ---------- ---------- ----------- --------- ----------- ---------- ---------- ----------- 1 0 28451 0 2966675 0 3604784 0 4926092069
show interface port-channel 〈PORT-CHANNEL-ID〉 counters verbose
Displays counters by port-channel in details.
Syntax
show interface port-channel <PORT-CHANNEL-ID> counters verbose
Parameters
<PORT-CHANNEL-ID> — ID of port-channel. The parameter can be a range or an enumeration (e.g.: interface interface port-channel 1-5 or interface interface interface port-channel 1,5).
Privilege group
view-interface-front-port, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface port-channel 32 counters verbose Port-channel 32 statistics Rx Bytes 4926092069 Rx Packets 3631835 Rx Unicast Packets 27049 Rx Multicast Packets 3604784 Rx Broadcast Packets 2 Rx Error Packets 0 Rx Unknown Proto Packets 0 Tx Bytes 2966675 Tx Packets 28855 Tx Unicast Packets 28451 Tx Multicast Packets 391 Tx Broadcast Packets 13 Tx Error Packets 0 Rx frames 64 560 Rx frames 65-127 27140 Rx frames 128-255 39 Rx frames 256-511 0 Rx frames 512-1023 0 Rx frames 1024-1518 3604094 Rx frames 1519-2047 0 Rx frames 2048-4095 0 Rx frames 4096-9216 0 Rx frames 9217-16383 0 Tx frames 64 2 Tx frames 65-127 28832 Tx frames 128-255 21 Tx frames 256-511 0 Tx frames 512-1023 0 Tx frames 1024-1518 0 Tx frames 1519-2047 0 Tx frames 2048-4095 0 Tx frames 4096-9216 0 Tx frames 9217-16383 0
show interface port-channel 〈PORT-CHANNEL-ID〉 utilization
Displays utilization by port-channel.
Syntax
show interface port-channel <PORT-CHANNEL-ID> utilization
Parameters
<PORT-CHANNEL-ID> – ID port-channel. Параметр можно задавать диапазоном или перечислением (например: interface port-channel 1-5 или interface interface port-channel 1,5).
Privilege group
view-interface-front-port, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface port-channel 1 utilization 1 minute utilization average Port Tx Kbits/sec Rx Kbits/sec Tx Frames/sec Rx Frames/sec ---- ------------ ------------ ------------- ------------- 1 500 0 20 0 5 minute utilization average Port Tx Kbits/sec Rx Kbits/sec Tx Frames/sec Rx Frames/sec ---- ------------ ------------ ------------- ------------- 1 340 0 33 0
show interface ont 〈PORT-ID〉[/ONT-ID] connections
Displays list of last ONT to OLT connection/disconnection.
Syntax
show interface ont <PORT-ID>[/ONT-ID] connections
Parameters
<PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (e.g.: interface ont 1-3 or interface ont 1,3,5,7);
[ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (e.g.: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 6/2 connections ----------------------------------- [ONT 6/2] connections ----------------------------------- ---------------------------------------------- Serial number: ELTX660421C4 Equipment ID: NTU-RG-1421G-Wac Software version: 3.40.1.1655 LinkUp: 16.05.2022 05:46:39 LinkDown: 17.05.2022 03:49:04 Last state: Disconnected
show interface ont 〈PORT-ID〉[/ONT-ID] configuration
Displays current active ONT configuration. Symbol "T" means that the parameter is used from assigned template.
Syntax
show interface ont <PORT-ID>[/ONT-ID] configuration
Parameters
<PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (e.g.: interface ont 1-3 or interface ont 1,3,5,7);
[ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (e.g.: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 3/3 configuration
-----------------------------------
[ONT 3/3] configuration
-----------------------------------
Description
Enabled: true
Serial:
Password: 0000000000
Rf port state: disabled
Broadcast filter: true
Multicast filter: true
Profile shaping: n/a
Profile management: n/a
Profile ports: ports1
Service[1]:
[T] Profile cross connect: 333 ONT Profile Cross-Connect 6
[T] Profile dba: 3play_dba ONT Profile DBA 2
Template: two_services
iphost management static ip: 0.0.0.0
iphost management static mask: 0.0.0.0
iphost management static gateway: 0.0.0.0
show interface ont 〈PORT-ID〉[/ONT-ID] ports
Displays ONT LAN ports status.
Syntax
show interface ont <PORT-ID>[/ONT-ID] ports
Parameters
<PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (e.g.: interface ont 1-3 or interface ont 1,3,5,7);
[ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (e.g.: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 6/2 ports ----------------------------------- [ONT 6/2] ports state ----------------------------------- UNI ## 1 2 3 4 Link: up down down down Speed: 1G n/a n/a n/a Duplex: full n/a n/a n/a
show interface ont 〈PORT-ID〉[/ONT-ID] laser
ONT laser status query.
Syntax
show interface ont <PORT-ID>[/ONT-ID] laser
Parameters
<PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (e.g.: interface ont 1-3 or interface ont 1,3,5,7);
[ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (e.g.: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-interface-ont
Command mode
ROOT
Example
LTP-16N# show interface ont 6/2 laser
-----------------------------------
[ONT 6/2] Laser info
-----------------------------------
Voltage: 3.30 [V]
Bias current: 12.64 [mA]
Temperature: 40.80 [C]
Tx power: 2.47 [dBm]
Rx power: -17.01 [dBm]
Transceiver P/N: s
RF port status: n/a
Video power: n/a
show interface port-channel 〈PORT-CHANNEL-ID〉 state
Displayss state by port-channels.
Syntax
show interface port-channel <PORT-CHANNEL-ID> counters verbose
Parameters
<PORT-CHANNEL-ID> — ID of port-channel. The parameter can be a range or an enumeration (e.g.: interface interface port-channel 1-5 or interface interface interface port-channel 1,5).
Privilege group
view-interface-front-port, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface port-channel 1 state
Port-channel 1 status information:
Status: up
Common speed: 1G
Front-port from channel status:
Front-port 1
Status: up
Media: copper
Speed: 1G
show interface pon-port 〈PORT-ID〉 state
Displays state by pon ports.
Syntax
show interface pon <PORT-ID> state
Parameters
<ID> — port index in the range [1-16]. The parameter can be set by a range or enumeration (e.g.: interface pon-port 1-5 or interface pon-port 1,5).
Privilege group
view-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface pon-port 1 state Port State ONT count SFP vendor SFP product number SFP vendor revision SFP temperature [C] SFP voltage [V] SFP tx bias current [mA] SFP tx power [dBm] ---- -------- --------- ------------------ ------------------ ------------------- ------------------- --------------- ------------------------ ------------------ 1 OK 1 Ligent Photonics LTE3680P-BH 1.0 52 3.27 17.55 5.35
show interface pon-port 〈PORT-ID〉 utilization
Displays pon ports utilization.
Syntax
show interface pon <PORT-ID> utilization
Parameters
<ID> — port index in the range [1-16]. The parameter can be set by a range or enumeration (e.g.: interface pon-port 1-5 or interface pon-port 1,5).
Privilege group
view-interface-front-port
Command mode
ROOT
Example
LTP-16N# show interface pon-port 3 utilization 1 minute utilization average Port Tx Kbits/sec Rx Kbits/sec Tx Frames/sec Rx Frames/sec ---- ------------ ------------ ------------- ------------- 3 0 16 0 20 5 minute utilization average Port Tx Kbits/sec Rx Kbits/sec Tx Frames/sec Rx Frames/sec ---- ------------ ------------ ------------- ------------- 3 0 15 0 19
show ip igmp snooping config vlan
Displays IGMP configuration for a given VLAN.
Syntax
show ip igmp snooping config vlan <VID>
Parameters
<VID> — VLAN ID in the range [1-4094].
Privilege group
view-igmp
Command mode
ROOT
Example
LTP-16N# show ip igmp snooping config vlan 99
---------------------
VLAN 99 IGMP settings
---------------------
snooping: enabled
fast leave: disabled
querier: enabled
learning: enabled
multicast loopback: disabled
robustness variable: 2
query interval: 125
query response interval: 100
querier ip address: 0.0.0.0
source ip address: 0.0.0.0
dscp: 0
igmp version: V1_V2_V3
mc router ports: none
show ip igmp snooping groups
Displays the multicast group added via IGMP. With VLAN ID filtering capability.
Syntax
show ip igmp snooping groups[vlan <VID>]
Parameters
<VID> — VLAN ID in the range [1-4094].
Privilege group
view-igmp
Command mode
ROOT
Example
LTP-16N# show ip igmp snooping groups
VLAN 99: groups count — 1
1: 239.25.25.25
Filter mode EXCLUDE
Member pon-port 1, expires 00:05:34
Filter mode EXCLUDE
Group expires 00:05:34
show ip igmp snooping hosts
Displays the list of ports with connected hosts. With VLAN ID filtering capability.
Syntax
show ip igmp snooping hosts [vlan <VID>]
Parameters
<VID> — VLAN ID in the range [1-4094].
Privilege group
view-igmp
Command mode
ROOT
Example
LTP-16N# show ip igmp snooping hosts vlan 99
Hosts ports. VLAN 99.
pon-port 1 00:00:00
pon-port 2 00:00:00
pon-port 3 00:00:00
pon-port 4 00:00:00
pon-port 5 00:00:00
pon-port 6 00:00:00
pon-port 7 00:00:00
pon-port 8 00:00:00
pon-port 9 00:03:15
pon-port 10 00:00:00
pon-port 11 00:00:00
pon-port 12 00:00:00
pon-port 13 00:00:00
pon-port 14 00:00:00
pon-port 15 00:00:00
pon-port 16 00:00:00
show ip igmp snooping mroute
Displays the list of ports with connected mroute. With VLAN ID filtering capability.
Syntax
show ip igmp snooping mroute [vlan <VID>]
Parameters
<VID> — VLAN ID in the range [1-4094].
Privilege group
view-igmp
Command mode
ROOT
Example
LTP-16N# show ip igmp snooping mrouters
Multicast routers ports. VLAN 99.
front-port 1 00:00:00
show ip dhcp sessions
Displays active dhcp sessions.
Syntax
show ip dhcp sessions
Parameters
The command does not contain any parameters.
Privilege group
view-dhcp
Command mode
ROOT
Example
LTP-16N# show ip dhcp sessions
DHCP sessions (1):
## Serial PON-port ONT-ID Service IP MAC Vid GEM Life time
---- ------------ --------- ------ ------- --------------- ----------------- ---- ---- ---------
1 ELTX6C000090 1 1 1 192.168.101.75 E0:D9:E3:6A:28:F0 1100 129 3503
show ip dhcp sessions 〈FILTER〉
Displays active dhcp sessions by filter.
Syntax
show ip dhcp sessions <FILTER> <VALUE>
Parameters
<FILTER>
show ip dhcp sessions 〈FILTER〉
Displays active dhcp sessions by filter.
Syntax
show ip dhcp sessions <FILTER> <VALUE>
Parameters
<FILTER> — filters for MAC table:
- interface — filter dhcp sessions by interface type. <VALUE> values are available for this filter:
- gpon-port — filter dhcp sessions of the specified gpon-ports;
- ont- filter dhcp sessions of the specified ont;
- vlan — filter dhcp sessions by vlan. <VALUE> values are available for this filter:
- vlan index [1-4094]. The parameter can be specified as a range or an enumeration (For example: vlan 10-30 or vlan 10,40,70).
Privilege group
view-dhcp
Command mode
ROOT
Example
LTP-16N# show ip dhcp sessions interface ont 1/1
DHCP sessions (1):
## Serial PON-port ONT-ID Service IP MAC Vid GEM Life time
---- ------------ --------- ------ ------- --------------- ----------------- ---- ---- ---------
1 ELTX6C000090 1 1 1 192.168.101.75 E0:D9:E3:6A:28:F0 1100 129 3503
show ip pppoe sessions
Displays active dhcp sessions.
Syntax
show ip pppoe sessions
Parameters
The command does not contain any parameters.
Privilege group
view-pppoe
Command mode
ROOT
Example
LTP-16N# show ip pppoe sessions PPPoE sessions (2): ## Serial PON-port Ont ID GEM Client MAC Session ID Duration Unblock ---- ------------ --------- ------ ---- ----------------- ---------- --------- --------- 1 ELTX74000A34 8 20 882 E0:D9:E3:9C:D4:5B 0x39cf 0:07:02 0:00:00 2 ELTX7400018C 7 31 1190 E0:D9:E3:9C:C3:0C 0x0eb4 0:06:54 0:00:00
show ip pppoe sessions 〈FILTER〉
Displays active dhcp sessions by filter.
Syntax
show ip pppoe sessions <FILTER> <VALUE>
Parameters
<FILTER> — filters for MAC table:
- interface — filter ppoe sessions by interface type. <VALUE> values are available for this filter:
- gpon-port — filter ppoe sessions of the specified gpon-ports;
- ont- filter ppoe sessions of the specified ont;
- vlan — filter ppoe sessions by vlan. <VALUE> values are available for this filter:
- vlan index [1-4094]. The parameter can be specified as a range or an enumeration (For example: vlan 10-30 or vlan 10,40,70).
Privilege group
view-pppoe
Command mode
ROOT
Example
LTP-16N# show ip pppoe sessions interface pon 8 PPPoE sessions (1): ## Serial pon-port Ont ID GEM Client MAC Session ID Duration Unblock -- ------------ ------- ----- --- ----------- ------- ------ ----- 1 ELTX74000A34 8 20 882 E0:D9:E3:9C:D4:5B 0x39cf 0:07:02 0:00:00
show license
Displays information on the current license.
Syntax
show license
Parameters
The command does not contain parameters.
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# show license
Active license information:
License valid: yes
Version: 1.2
Board SN: GP3D000033
Licensed vendor: all
Licensed ONT count: unlimited
Licensed ONT online: n/a
show log buffer
Displays last log from buffer.
Syntax
show log buffer
Parameters
The command does not contain any parameters.
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# show log buffer 09 Sep 11:49:31 NOTICE DNA BCM-API — Device reset: OK 09 Sep 11:49:51 NOTICE DNA BCM-API — Device connection is complete system_mode is gpon__16_x 09 Sep 11:49:51 NOTICE DNA BCM-API — Connect to device: OK 09 Sep 11:49:51 NOTICE DNA BCM-API — Qumran CLI command (vlan create 3470 pbm=ge140) execution: OK 09 Sep 11:49:51 NOTICE DNA BCM-API — Qumran CLI command (port xe128 speed=1000) execution: OK 09 Sep 11:49:51 NOTICE DNA BCM-API — Qumran CLI command (vlan add 3470 pbm=xe128) execution: OK 09 Sep 11:49:51 NOTICE DNA BCM-API — Getting 1 front-port info: OK 09 Sep 11:49:51 NOTICE DNA BCM-API — Getting 2 front-port info: OK 09 Sep 11:49:51 NOTICE DNA BCM-API — Getting 3 front-port info: OK 09 Sep 11:49:51 NOTICE DNA BCM-API — Getting 4 front-port info: OK 09 Sep 11:49:51 NOTICE DNA BCM-API — Getting 5 front-port info: OK 09 Sep 11:49:51 NOTICE DNA BCM-API — Getting 6 front-port info: OK 09 Sep 11:49:51 NOTICE DNA BCM-API — Getting 7 front-port info: OK 09 Sep 11:49:51 NOTICE DNA BCM-API — Getting 8 front-port info: OK
show log files
Displays the list of files with logs.
Syntax
show log files
Parameters
The command does not contain any parameters.
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# show log files
## Name Size in bytes Date of last modification
1 LTP.log.2 109640 Tue Sep 8 10:11:18 2020
2 LTP.log.3 120404 Tue Sep 8 10:11:18 2020
3 LTP.log 3340 Tue Sep 8 10:27:40 2020
Total files: 3
show log 〈FILENAME〉
Displays logs from file.
Syntax
show log <FILENAME>
Parameters
<FILENAME> — file name from the list that available by the show log files command.
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# show log LTP.log 09 Sep 11:50:51 NOTICE DNA BCM-API — ONT 1/1 activation: OK 09 Sep 11:51:01 NOTICE DNA BCM-API — Found unactivated ONU ELTX6C000090 on PON-PORT 1 09 Sep 11:51:01 NOTICE ONT 1/1 — Activation: OK 09 Sep 11:51:03 NOTICE ONT 1/1 — ONT Vendor: ELTX Type: NTU1421GCWAC (1v1) FW version: 3.40.2.109 09 Sep 11:51:03 NOTICE DNA BCM-API — Alloc-ID 767 (ONT 1/1) creation: OK 09 Sep 11:51:03 NOTICE DNA BCM-API — Flow (id 63998, type 0) destruction: OK 09 Sep 11:51:03 NOTICE DNA BCM-API — Upstream flow 63998 creation: OK 09 Sep 11:51:03 NOTICE FSM-PON — OLT side datapath configured. 09 Sep 11:51:04 NOTICE ONT 1/1 — ONT_OK Successful activation and configuration 09 Sep 11:51:19 NOTICE DNA BCM-API — Flow (id 1598, type 2) destruction: OK 09 Sep 11:51:19 NOTICE DNA BCM-API — Multicast flow 1598 creation: OK 09 Sep 11:51:19 NOTICE DNA BCM-API — Updating group #0, command — add: OK 09 Sep 11:51:32 NOTICE DNA BCM-API — Flow (id 63998, type 0) destruction: OK 09 Sep 11:51:32 NOTICE DNA BCM-API — Alloc-ID 767 (PON port 1) destruction: OK
show lldp stats [interface front-port 〈PORT-ID〉]
Displays LLDP statistics. Output is filtered by interface if adding the interface front-port <PORT-ID> parameter.
Syntax
show lldp stats
show lldp stats interface front-port <PORT-ID>
Parameters
<PORT-ID> — port index in the range [1-8]. The parameter can be set by a range or enumeration (for example: interface pon-port 1-5 or interface pon-port 1,5).
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# show lldp stats
Table Last Change Time: 0 days 00:00:00
Table Inserts: 0
Table Deletes: 0
Table AgeOut Count: 0
LLDP interface statistics
## Tx total Rx total Rx errors TLVs discarded AgeOut count
---- -------- -------- --------- -------- -----------
1 0 0 0 0 0
2 0 0 0 0 0
3 15 0 0 0 0
4 0 0 0 0 0
5 15 0 0 0 0
6 0 0 0 0 0
7 0 0 0 0 0
8 0 0 0 0 0
show lldp local [interface front-port 〈PORT-ID〉]
Displays local information on LLDP. Output is filtered by interface if adding the interface front-port <PORT-ID> parameter.
Syntax
show lldp local
show lldp local interface front-port <PORT-ID>
Parameters
<PORT-ID> — port index in the range [1-8]. The parameter can be set by a range or enumeration (for example: interface pon-port 1-5 or interface pon-port 1,5).
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# show lldp local
Local Interfaces LLDP info
## Chassis ID Port ID Capabilities Management address TTL
---- ----------------- ------------- ---------- ----------------- -----
1 E4:5A:D4:1A:05:60 front-port 1 Bridge 192.168.10.145 20
2 E4:5A:D4:1A:05:60 front-port 2 20
3 E4:5A:D4:1A:05:60 front-port 3 20
4 E4:5A:D4:1A:05:60 front-port 4 20
5 E4:5A:D4:1A:05:60 front-port 5 20
6 E4:5A:D4:1A:05:60 front-port 6 20
7 E4:5A:D4:1A:05:60 front-port 7 20
8 E4:5A:D4:1A:05:60 front-port 8 20
show lldp neighbors [interface front-port 〈PORT-ID〉] [verbose]
Displays information about neighbors received via LLDP. Output is filtered by interface if adding the interface front-port <PORT-ID> parameter. Adding verbose expands output.
Syntax
show lldp neighbors
show lldp neighbors verbose
show lldp neighbors interface front-port <PORT-ID>
show lldp neighbors interface front-port <PORT-ID> verbose
Parameters
<PORT-ID> — port index in the range [1-8]. The parameter can be set by a range or enumeration (for example: interface pon-port 1-5 or interface pon-port 1,5).
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# show lldp neighbors interface front-port 1
Neighbor Interfaces LLDP info
## Chassis ID Port ID Capabilities Management address TTL
---- ------------------ --------- ------------ ----------------- -----
1 A8:F9:4B:84:F5:40 te1/0/2 Bridge, Router 192.168.11.150 37/40
show running-config
Displays current running configuration.
Syntax
show running-config
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config
configure terminal
management ip 192.168.100.1
exit
commit
exit
show running-config all
Displays all current running configuration, including default values.
Syntax
show running-config all
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config all
configure terminal
interface pon-port 1
no shutdown
exit
interface pon-port 2
no shutdown
exit
interface pon-port 3
no shutdown
exit
interface pon-port 4
no shutdown
exit
interface pon-port 5
no shutdown
exit
interface pon-port 6
no shutdown
exit
interface pon-port 7
no shutdown
exit
interface pon-port 8
--More--(0%)
show running-config alarm
Displays the running configuration for alarms. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config alarm [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config alarm
LTP-16N# show running-config alarm all
alarm
system-fan max-rpm 12000
system-fan min-rpm 2000
system-fan severity critical
system-fan in true
system-fan out true
system-load-average level 0
system-load-average severity critical
system-load-average in true
system-load-average out true
system-ram free 12
system-ram severity critical
system-ram in true
system-ram out true
system-temperature sensor pon-ports-1 min 0
system-temperature sensor pon-ports-1 max 70
system-temperature sensor pon-ports-2 min 0
system-temperature sensor pon-ports-2 max 70
system-temperature sensor front-ports min 0
system-temperature sensor front-ports max 70
system-temperature sensor switch min 0
system-temperature sensor switch max 70
system-temperature severity critical
--More--(46%)
show running-config cli
Displays the running configuration for CLI. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config cli [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config cli all cli timeout 1800 cli max-sessions 5
show running-config interface front-port
Displays the running configuration for front-port. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config interface front-port <PORT-ID> [all]
Parameters
<PORT-ID> — port index in the range [1-8]. The parameter can be set by a range or enumeration (for example: interface pon-port 1-5 or interface pon-port 1,5).
Privilege group
view-configuration, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show running-config interface front-port 1-2 all
interface front-port 1
no shutdown
no vlan allow 1-4094
switchport mode trunk
exit
interface front-port 2
no shutdown
no vlan allow 1-4094
switchport mode trunk
exit
show running-config interface pon-port
Displays the running configuration for pon-port. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config interface pon-port <PORT-ID> [all]
Parameters
<PORT-ID> — port index in the range [1-16]. The parameter can be set by a range or enumeration (for example: interface pon-port 1-5 or interface pon-port 1,3,5,7).
Privilege group
view-configuration, config-interface-pon-port
Command mode
ROOT
Example
LTP-16N# show running-config interface pon-port 15,16 all
interface pon-port 15
no shutdown
exit
interface pon-port 16
no shutdown
exit
show running-config interface ont
Displays the running configuration for ONT. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config interface ont <PORT-ID>[/ONT-ID] [all]
Parameters
- <PORT-ID> — pon port index in the range [1-16]. The parameter can be set by a range or enumeration (For example: interface ont 1-3 or interface ont 1,3,5,7).
- [ONT-ID] — ONT index in the range [1-128]. The parameter can be set by a range or enumeration (For example: interface ont 1/5-7 or interface ont 1-7/1,3,5,7).
Privilege group
view-configuration, config-interface-ont
Command mode
ROOT
Example
LTP-16N# show running-config interface ont 1/1 all
interface ont 1/1
service 1 profile cross-connect "" dba ""
service 2 profile cross-connect "" dba ""
service 3 profile cross-connect "" dba ""
service 4 profile cross-connect "" dba ""
service 5 profile cross-connect "" dba ""
service 6 profile cross-connect "" dba ""
service 7 profile cross-connect "" dba ""
service 8 profile cross-connect "" dba ""
service 9 profile cross-connect "" dba ""
service 10 profile cross-connect "" dba ""
service 11 profile cross-connect "" dba ""
service 12 profile cross-connect "" dba ""
service 13 profile cross-connect "" dba ""
service 14 profile cross-connect "" dba ""
service 15 profile cross-connect "" dba ""
service 16 profile cross-connect "" dba ""
service 17 profile cross-connect "" dba ""
service 18 profile cross-connect "" dba ""
service 19 profile cross-connect "" dba ""
service 20 profile cross-connect "" dba ""
service 21 profile cross-connect "" dba ""
service 22 profile cross-connect "" dba ""
--More--(63%)
show running-config ip dhcp
Displays running configuration for DHCP. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config ip dhcp [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config ip dhcp
ip dhcp
snooping enable
exit
show running-config ip igmp
Displays running configuration for IGMP. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config ip igmp [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config ip igmp ip igmp snooping
show running-config ip pppoe
Displays running configuration for PPPoE. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config ip pppoe [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config ip pppoe
ip pppoe
snooping enable
exit
show running-config ip snmp
Displays candidate configuration for SNMP. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config ip snmp [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config ip snmp ip snmp contact Eltex
show running-config ip ssh
Displays running configuration for SSH. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config ip ssh [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config ip ssh no ip ssh enable
show running-config ip telnet
Displays running configuration for TELNET. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config ip telnet [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config ip telnet no ip telnet enable
show running-config ip ntp
Displays running configuration for NTP. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config ip ntp [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config ip ntp all ip ntp enable ip ntp server 192.168.100.2 ip ntp interval 1024 ip ntp timezone hours 0 minutes 0 no ip ntp daylightsaving start no ip ntp daylightsaving end
show running-config port-channel
Displays running configuration for port-channel. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config interface port-channel <PORT-CHANNEL-ID>
Parameters
<PORT-CHANNEL-ID> — ID of port-channel. The parameter can be a range or an enumeration (for example: interface interface port-channel 1-5 or interface interface interface port-channel 1,5).
Privilege group
view-configuration, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show running-config interface port-channel 1
interface port-channel 1
vlan allow 99
exit
show running-config port-channel load-balance
Displays running configuration for port-channel load-balance. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config interface port-channel load-balance
Parameters
The command does not contain any parameters.
Privilege group
view-configuration, config-interface-front-port
Command mode
ROOT
Example
LTP-16N# show running-config interface port-channel load-balance interface port-channel load-balance hash src-mac dst-mac interface port-channel load-balance polynomial 0x84a1
show running-config logging
Displays running configuration for logging. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config logging [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration, config-logging
Command mode
ROOT
Example
LTP-16N# show running-config logging all
logging
module dna loglevel notice
module dna bcm-api loglevel notice
module dna tools loglevel notice
module dna loglib loglevel notice
module dna cfgdb loglevel notice
module dna conf-task loglevel notice
module dna olt loglevel notice
module dna pon-port 1 loglevel notice
module dna pon-port 2 loglevel notice
module dna pon-port 3 loglevel notice
module dna pon-port 4 loglevel notice
module dna pon-port 5 loglevel notice
module dna pon-port 6 loglevel notice
module dna pon-port 7 loglevel notice
module dna pon-port 8 loglevel notice
module dna pon-port 9 loglevel notice
module dna pon-port 10 loglevel notice
module dna pon-port 11 loglevel notice
module dna pon-port 12 loglevel notice
module dna pon-port 13 loglevel notice
module dna pon-port 14 loglevel notice
module dna pon-port 15 loglevel notice
--More--(1%)
show running-config lldp
Displays running configuration for lldp. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config lldp [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config lldp lldp enable
show running-config management
Displays the running configuration of network management settings. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config management [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration, config-management
Command mode
ROOT
Example
LTP-16N# show running-config management all management ip 192.168.1.2 management mask 255.255.255.0 management gateway 0.0.0.0 management vid 1
show running-config mirror 〈ID〉
Displays the running configuration of network management settings. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config management [all]
Parameters
<ID> — mirror ID. The parameter can be a range or an enumeration (For example: mirror 1-5 or mirror 1,5).
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config mirror 1 all
mirror 1
no source interface pon-port 1
no source interface pon-port 2
no source interface pon-port 3
no source interface pon-port 4
no source interface pon-port 5
no source interface pon-port 6
no source interface pon-port 7
no source interface pon-port 8
no source interface pon-port 9
no source interface pon-port 10
no source interface pon-port 11
no source interface pon-port 12
no source interface pon-port 13
no source interface pon-port 14
no source interface pon-port 15
no source interface pon-port 16
no source interface front-port 1
no source interface front-port 2
no source interface front-port 3
no source interface front-port 4
no source interface front-port 5
no source interface front-port 6
no source interface front-port 7
no source interface front-port 8
no destination interface
exit
LTP-16N#
show running-config pon
Displays the running configuration for pon. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config pon [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config pon all pon network svlan-ethertype 802.1q
show running-config privilege
Displays running configuration for privileges. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config privilege [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration, config-user
Command mode
ROOT
Example
LTP-16N# show running-config privilege all privilege 1 view-interface-ont privilege 2 view-interface-ont privilege 2 commands-interface-ont privilege 4 view-interface-ont privilege 4 config-general privilege 4 config-interface-ont privilege 4 commands-interface-ont privilege 4 commands-configuration privilege 5 view-interface-ont privilege 5 config-general privilege 5 config-interface-ont privilege 5 config-interface-ont-profile privilege 5 commands-interface-ont privilege 5 commands-configuration privilege 6 view-interface-ont privilege 6 config-general privilege 6 config-interface-pon-port privilege 6 config-interface-ont privilege 6 config-interface-ont-profile privilege 6 commands-interface-ont privilege 6 commands-configuration privilege 6 commands-interface-pon-port privilege 7 view-igmp --More--(18%)
show running-config profile cross-connect
Displays running configuration for cross-connect profile. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config profile cross-connect [NAME] [all]
Parameters
[NAME] — profile name. A set of characters from 1 to 15 in length.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show running-config profile cross-connect HSI
profile cross-connect HSI
bridge enable
bridge group 10
outer vid 100
exit
LTP-16N# show running-config profile cross-connect all
profile cross-connect HSI
pon vid no-change
user vid untagged
description
bridge enable
bridge group 10
outer vid 100
traffic-model n-to-1
exit
show running-config profile dba
Displays running configuration for DBA profile. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config profile dba [NAME] [all]
Parameters
[NAME] — profile name. A set of characters from 1 to 15 in length.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show running-config profile dba all
profile dba dba
description
bandwidth besteffort 1244160
bandwidth guaranteed 512
allocation-scheme share-t-cont
mode non-status-reporting
exit
show running-config profile ports
Displays running configuration for ports profile. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config profile ports [NAME] [all]
Parameters
[NAME] — profile name. A set of characters from 1 to 15 in length.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show running-config profile ports
profile ports pp
port 1 bridge group 10
exit
LTP-16N# show running-config profile ports all
profile ports pp
no port 1 multicast
port 1 bridge group 10
port 1 igmp downstream priority 0
port 1 igmp downstream tag-control pass
port 1 igmp downstream vid 0
port 1 igmp upstream priority 0
port 1 igmp upstream tag-control pass
port 1 igmp upstream vid 0
no port 2 multicast
port 2 bridge group 0
port 2 igmp downstream priority 0
port 2 igmp downstream tag-control pass
port 2 igmp downstream vid 0
port 2 igmp upstream priority 0
port 2 igmp upstream tag-control pass
port 2 igmp upstream vid 0
no port 3 multicast
port 3 bridge group 0
port 3 igmp downstream priority 0
port 3 igmp downstream tag-control pass
port 3 igmp downstream vid 0
port 3 igmp upstream priority 0
port 3 igmp upstream tag-control pass
port 3 igmp upstream vid 0
no port 4 multicast
port 4 bridge group 0
port 4 igmp downstream priority 0
port 4 igmp downstream tag-control pass
port 4 igmp downstream vid 0
port 4 igmp upstream priority 0
port 4 igmp upstream tag-control pass
port 4 igmp upstream vid 0
igmp mode snooping
igmp querier
igmp robustness 2
igmp version 3
igmp query interval 125
--More--(94%)
show running-config system
Displays running of system configuration. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config system [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config system all system hostname LTP-16N system fan speed auto
show running-config profile management
Displays running configuration for management interface profile. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config profile management [NAME]
Parameters
[NAME] — profile name. A set of characters from 1 to 15 in length.
Privilege group
view-configuration, config-interface-ont-profile
Command mode
ROOT
Example
LTP-16N# show running-config profile management
profile management MANAGEMENT
iphost id 3
exit
show running-config profile dhcp-opt82
Displays running configuration for dhcp-opt82 profile.
Syntax
show running-config profile dhcp-opt82 [NAME]
Parameters
[NAME] — profile name. A set of characters from 1 to 15 in length.
Privilege group
view-configuration, config-dhcp
Command mode
ROOT
Example
LTP-16N# show running-config profile dhcp-opt82
profile dhcp-opt82 DHCP-82
ont-sn-format numerical
exit
show running-config profile pppoe-ia
Displays running configuration for pppoe-ai profile.
Syntax
show running-config profile pppoe-ia [NAME]
Parameters
[NAME] — profile name. A set of characters from 1 to 15 in length.
Privilege group
view-configuration, config-pppoe
Command mode
ROOT
Example
LTP-16N# show running-config profile pppoe-ia
profile pppoe-ia PPPOE
ont-sn-format numerical
exit
show running-config qos
Displays running configuration for QoS. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config qos [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration
Command mode
ROOT
Example
LTP-16N# show running-config qos all no qos enable qos type 802.1p qos 802.1p mode sp qos 802.1p wfq queues-weight 7 15 23 31 39 47 55 63 qos 802.1p map 0 to 0 qos 802.1p map 1 to 1 qos 802.1p map 2 to 2 qos 802.1p map 3 to 3 qos 802.1p map 4 to 4 qos 802.1p map 5 to 5 qos 802.1p map 6 to 6 qos 802.1p map 7 to 7
show running-config user
Displays running configuration for users. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config user [all]
Parameters
The command does not contain any parameters.
Privilege group
view-configuration, config-user
Command mode
ROOT
Example
LTP-16N# show running-config user user test encrypted_password $6$YocBrXdZ$/QPfwUYYrSdXgTm4YpCvo7D5sxiq0gfQ.Lbf.xaEDMvXLE9DqD/6HEG4sBSKfbA1uicizAr0SIIJRqgdgeuii0 user test privilege 0
show running-config vlan
Displays running configuration for VLAN. When adding an all postfix, the whole configuration will be displayed, including the default values.
Syntax
show running-config vlan <VID> [all]
Parameters
<VID> — VLAN ID in the range [1-4094].
Privilege group
view-configuration, config-vlan
Command mode
ROOT
Example
LTP-16N# show running-config vlan 1000
vlan 1000
ip igmp snooping enable
exit
LTP-16N# show running-config vlan 1000 all
vlan 1000
name
ip igmp snooping enable
ip igmp snooping querier enable
ip igmp query-interval 125
ip igmp query-response-interval 100
ip igmp robustness-variable 2
ip igmp last-member-query-interval 10
ip igmp snooping replace source-ip 0.0.0.0
ip igmp snooping querier ip-address 0.0.0.0
no ip igmp snooping querier fast-leave
ip igmp snooping querier dscp 0
ip igmp version v1-v2-v3
ip igmp snooping mrouter pon-port 1
ip igmp snooping mrouter pon-port 2
ip igmp snooping mrouter pon-port 3
ip igmp snooping mrouter pon-port 4
ip igmp snooping mrouter pon-port 5
ip igmp snooping mrouter pon-port 6
ip igmp snooping mrouter pon-port 7
ip igmp snooping mrouter pon-port 8
ip igmp snooping mrouter pon-port 9
ip igmp snooping mrouter pon-port 10
--More--(58%)
show system environment
Displays device system information.
Syntax
show system environment
Parameters
The command does not contain any parameters.
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# show system environment
System information:
CPU load average (1m, 5m, 15m): 4.540 2.380 0.960
Free RAM/Total RAM (Gb): 4.59/7.76
Free disk space/Total disk space(Gb)): 5.73/6.13
Temperature:
Sensor PON SFP 1 (*C): 50
Sensor PON SFP 2 (*C): 37
Sensor Front SFP (*C): 41
Sensor Switch (*C): 35
Fan state:
Fan 1 (rpm): offline
Fan 2 (rpm): offline
Fan 3 (rpm): offline
Fan 4 (rpm): offline
Power supply information:
Module 1: offline
Module 2: PM160 220/12 1vX
Type: AC
Intact: true
HW information
FPGA version: 2.0
PLD version: 2.0
Factory
Type: LTP-16N
Revision: 1v2
SN: GP3D000026
MAC: E0:D9:E3:FF:24:B0
show version
Displays current firmware version.
Syntax
show version
Parameters
The command does not contain any parameters.
Privilege group
view-system
Command mode
ROOT
Example
LTP-16N# LTP-16N# show version
Eltex LTP-16N: software version 1.0.0 build 1128 on 08.09.2020 05:44
show mac
Displays MAC table.
Syntax
show mac
show mac verbose <FILTER> <FILTER_TYPE>
show mac <FILTER> <FILTER_TYPE>
Parameters
<FILTER> — excluding or including filter — include, exclude.
<FILTER_TYPE> — attribute by which filtering is performed — interface, mac, svid, cvid, gem, type. Multiple attributes for filtering can be specified.
Privilege group
config-vlan, config-igmp, config-general, config-system, config-logging, config-interface-pon-port, config-interface-ont, config-interface-ont-profile,
config-interface-front-port, config-access, config-cli, config-management, config-user
Command mode
ROOT
Example
LTP-16N# show mac verbose
Loading MAC table...
MAC port svid cvid ONT gem type
------------------- ----------------- ------ ------ ----- ------- ---------
2C:56:DC:99:8E:63 pon-port 6 1100 6/2 181 Dynamic
1 MAC entries
show mac 〈FILTER〉
Displays MAC table by filter.
Syntax
show mac interface <FILTER> <VALUE>
Parameters
<FILTER> — filters for MAC table:
- interface — filter MAC table by interface type. <VALUE> values are available for this filter:
- front-port — filter MAC addresses of the specified front-ports;
- pon-port — filter MAC addresses of the specified pon-ports;
- port-channel — filter MAC addresses of the specified port-channels;
- vlan — filter MAC table by vlan. <VALUE> values are available for this filter:
- vlan index [1-4094]. The parameter can be specified as a range or an enumeration (For example: vlan 10-30 or vlan 10,40,70).
Privilege group
show mac interface: config-vlan, config-igmp, config-general, config-system, config-logging, config-interface-gpon-port, config-interface-ont, config-interface-ont-profile, config-interface-front-port, config-access, config-cli, config-management, config-user;
show mac vlan: view-configuration, view-firmware, config-vlan, config-igmp, config-ppoe, config-general, config-system, config-logging, config-interface-gpon-port, config-interface-ont, config-interface-ont-profile, config-interface-front-port.
Command mode
ROOT
Example
LTP-16N# show mac vlan 5
Loading MAC table...
MAC port
B4:2E:99:98:0C:76 front-port 5
1 MAC entries