WEP-1L, WEP-2L, WOP-2L configuration via SNMP is available starting firmware version 1.2.5.
OID for requests for all devices are as follows: .1.3.6.1.4.1.35265.1.127.
OID in traps for devices identification are different and are as follows: .1.3.6.1.4.1.35265.1.XXX, where XXX is device ID.
Below is a table that shows the correspondence between identifiers and device names.
ID | Device |
---|---|
172 | WOP-2L |
173 | WEP-2L |
174 | WEP-1L |
251 | WOP-20L |
260 | WEP-200L |
231 | WEP-30L |
280 | WOP-30L |
287 | WOP-30LS |
Monitoring
OID | Type | Description | Output example |
---|---|---|---|
Monitoring parameters of connected clients | |||
iso.3.6.1.4.1.35265.1.127.1.1.1.1.0 | INTEGER | Client index | "0" |
iso.3.6.1.4.1.35265.1.127.1.1.1.2.0 | STRING | Client MAC address | "e0:d9:e3:4d:66:60" |
iso.3.6.1.4.1.35265.1.127.1.1.1.3.0 | STRING | Interface/VAP name to which client is connected | "wlan1-va0" |
iso.3.6.1.4.1.35265.1.127.1.1.1.4.0 | INTEGER | RSSI-1 (on the first antenna) | "-26" |
iso.3.6.1.4.1.35265.1.127.1.1.1.5.0 | INTEGER | RSSI-2 (on the second antenna) | "-28" |
iso.3.6.1.4.1.35265.1.127.1.1.1.6.0 | INTEGER | SNR-1 (on the first antenna) | "16" |
iso.3.6.1.4.1.35265.1.127.1.1.1.7.0 | INTEGER | SNR-2 (on the second antenna) | "16" |
iso.3.6.1.4.1.35265.1.127.1.1.1.8.0 | STRING | Modulation for transmission (TX) | "VHT NSS1-MCS8 SGI 86.7" |
iso.3.6.1.4.1.35265.1.127.1.1.1.9.0 | STRING | Modulation for reception (RX) | "VHT NSS1-MCS8 NO SGI 78" |
iso.3.6.1.4.1.35265.1.127.1.1.1.10.0 | INTEGER | Transmission rate (kbps) | "303" |
iso.3.6.1.4.1.35265.1.127.1.1.1.11.0 | INTEGER | Reception rate (kbps) | "123" |
iso.3.6.1.4.1.35265.1.127.1.1.1.12.0 | INTEGER | Transmission bandwidth (MHz) | "20" |
iso.3.6.1.4.1.35265.1.127.1.1.1.13.0 | INTEGER | Reception bandwidth (MHz) | "20" |
Number of clients connected to device | |||
iso.3.6.1.4.1.35265.1.127.1.15.1.2.0 | INTEGER | Number of clients connected to 2.4 GHz radio interface | "3" |
iso.3.6.1.4.1.35265.1.127.1.15.1.2.1 | INTEGER | Number of clients connected to 5 GHz radio interface | "2" |
iso.3.6.1.4.1.35265.1.127.1.15.1.2.2 | INTEGER | Total number of clients connected to access point | "5" |
System parameters of the access point | |||
iso.3.6.1.4.1.35265.1.127.1.3.0 | INTEGER | Temperature | "33" |
iso.3.6.1.4.1.35265.1.127.1.4.0 | STRING | Firmware version | "1.2.5 build 13" |
iso.3.6.1.4.1.35265.1.127.1.7.0 | STRING | Serial number | "WP47000034" |
iso.3.6.1.4.1.35265.1.127.1.11.0 | INTEGER | sessionPasswordInitialized flag | "0" |
iso.3.6.1.4.1.35265.1.127.1.12.0 (systemUptime) | TIMETICKS | Device uptime | "21 minutes 35 seconds (129500)" |
iso.3.6.1.4.1.35265.1.127.1.13.0 (hardwareRevision) | STRING | Hardware version | "1v0" |
iso.3.6.1.4.1.35265.1.127.1.14.0 (secondarySwVersion) | STRING | Backup firmware version | "1.2.2 build 2" |
iso.3.6.1.4.1.2021.10.1.3 (from UCD-SNMP-MIB.txt) | OctetString | CPU load | laLoad.1: 5.65 laLoad.2: 4.22 laLoad.3: 2.06 |
iso.3.6.1.4.1.2021.4.5.0 (from UCD-SNMP-MIB.txt) | INTEGER | Объем общей RAM (Kbyte) | "216828" |
iso.3.6.1.4.1.2021.4.11.0 (from UCD-SNMP-MIB.txt) | INTEGER | Free RAM amount (Kbyte) | "129892" |
iso.3.6.1.2.1.4.20.1.1 (from IP-MIB.txt) | IpAddress | Interfaces IP addresses | "127.0.0.1" |
iso.3.6.1.2.1.2.2.1.5 (from IF-MIB.txt) | GAUGE32 | Maximum interface throughput (depends on radio mode, channel width, SGI, up/down) | ifSpeed.1-40: |
iso.3.6.1.2.1.1.3.0 (from RFC1213-MIB.txt) | TIMETICKS | SNMP agent uptime | - |
Interfaces statistics | |||
.1.3.6.1.4.1.35265.1.127.1.8.1.1 | OctetString | Interfaces names | |
.1.3.6.1.4.1.35265.1.127.1.8.1.2 | OctetString | Interfaces MAC addresses | |
.1.3.6.1.4.1.35265.1.127.1.8.1.3 | OctetString | Operational interfaces statuses | |
.1.3.6.1.4.1.35265.1.127.1.8.1.4 | INTEGER | MTU | |
.1.3.6.1.4.1.35265.1.127.1.8.1.5 | Counter32 | Number of bytes received on each interface (rxBytes) | |
.1.3.6.1.4.1.35265.1.127.1.8.1.6 | Counter32 | Number of packets received on each interface (rxPackets) | |
.1.3.6.1.4.1.35265.1.127.1.8.1.7 | Counter32 | Number of errors at reception on each interface (rxErrors) | |
.1.3.6.1.4.1.35265.1.127.1.8.1.8 | Counter32 | Numbers of drops at reception on each interface (rxDrop) | |
.1.3.6.1.4.1.35265.1.127.1.8.1.9 | Counter32 | rxFifo | |
.1.3.6.1.4.1.35265.1.127.1.8.1.10 | Counter32 | rxFrame | |
.1.3.6.1.4.1.35265.1.127.1.8.1.11 | Counter32 | rxCompressed | |
.1.3.6.1.4.1.35265.1.127.1.8.1.12 | Counter32 | rxMulticast | |
.1.3.6.1.4.1.35265.1.127.1.8.1.13 | Counter32 | Number of bytes sent from each interface (txBytes) | |
.1.3.6.1.4.1.35265.1.127.1.8.1.14 | Counter32 | Number of packets sent from each interface (txPackets) | |
.1.3.6.1.4.1.35265.1.127.1.8.1.15 | Counter32 | Number of transmission errors on each interface (txErrors) | |
.1.3.6.1.4.1.35265.1.127.1.8.1.16 | Counter32 | Number of packets dropped at transmission on each interface (txDrop) | |
.1.3.6.1.4.1.35265.1.127.1.8.1.17 | Counter32 | txFifo | |
.1.3.6.1.4.1.35265.1.127.1.8.1.18 | Counter32 | txColls | |
.1.3.6.1.4.1.35265.1.127.1.8.1.19 | Counter32 | txCarrier | |
.1.3.6.1.4.1.35265.1.127.1.8.1.20 | Counter32 | txCompressed | |
.1.3.6.1.4.1.35265.1.127.1.8.1.21 | INTEGER | Maximim interface throughput (linkSpeed) Depends on radio mode, channel width, SGI, up/down | |
.1.3.6.1.4.1.35265.1.127.1.8.1.22 | INTEGER | Actual reception rate on each interface, bps (actualrateRX) Calculated in 10 seconds | |
.1.3.6.1.4.1.35265.1.127.1.8.1.23 | INTEGER | Actual transmission rate on each interface, bps (actualrateTX) Calculated in 10 seconds | |
.1.3.6.1.4.1.35265.1.127.1.8.1.24 | INTEGER | Current load of the receiving interface, % (loadRX) Calculated as actualrateRX/linkSpeed ratio | |
.1.3.6.1.4.1.35265.1.127.1.8.1.25 | INTEGER | Current load of the receiving interface, % (loadTX) Calculated as actualrateRX/linkSpeed ratio | |
.1.3.6.1.4.1.35265.1.127.1.8.1.26 | INTEGER | Number of packets received with errors, pps (errorsppsRX) | |
.1.3.6.1.4.1.35265.1.127.1.8.1.27 | INTEGER | Number of packets transmitted with errors, pps (errorsppsTX) | |
.1.3.6.1.4.1.35265.1.127.1.8.1.28 | Counter64 | Number of bytes received on each interface (rxBytes64) | |
.1.3.6.1.4.1.35265.1.127.1.8.1.29 | Counter64 | Number of packets received on each interface (rxPackets64) | |
.1.3.6.1.4.1.35265.1.127.1.8.1.30 | Counter64 | Number of bytes sent on each interface (txBytes64) | |
.1.3.6.1.4.1.35265.1.127.1.8.1.31 | Counter64 | Number of packets sent on each interface (txPackets64) | |
.1.3.6.1.4.1.35265.1.127.1.8.1.32 | STRING | Duplex value for Ethernet interface (full/half) | |
Radio parameters | |||
iso.3.6.1.4.1.35265.1.127.1.9.1.1.0 | STRING | 2.4 GHz radio interface name | "wlan0" |
iso.3.6.1.4.1.35265.1.127.1.9.1.1.1 | STRING | 5 GHz radio interface name | "wlan1" |
iso.3.6.1.4.1.35265.1.127.1.9.1.2.0 | INTEGER | 2.4 GHz transmitter power (dBm) | "16" |
iso.3.6.1.4.1.35265.1.127.1.9.1.2.1 | INTEGER | 5 GHz transmitter power (dBm) | "19" |
iso.3.6.1.4.1.35265.1.127.1.9.1.3.0 | INTEGER | 2.4 GHz radio interface operating frequency (MHz) | "2412" |
iso.3.6.1.4.1.35265.1.127.1.9.1.3.1 | INTEGER | 5 GHz radio interface operating frequency (MHz) | "5700" |
iso.3.6.1.4.1.35265.1.127.1.9.1.4.0 | INTEGER | 2.4 GHz radio interface channel bandwidth (MHz) | "20' |
iso.3.6.1.4.1.35265.1.127.1.9.1.4.1 | INTEGER | 5 GHz radio interface channel bandwidth (MHz) | "20" |
iso.3.6.1.4.1.35265.1.127.1.9.1.5.0 | INTEGER | 2.4 GHz radio module temperature assessment | "31" |
iso.3.6.1.4.1.35265.1.127.1.9.1.5.1 | INTEGER | 5 GHz radio module temperature assessment | "35" |
iso.3.6.1.4.1.35265.1.127.1.9.1.6.0 | STRING | 2.4 GHz radio interface status | "on" |
iso.3.6.1.4.1.35265.1.127.1.9.1.6.1 | STRING | 5 GHz radio interface status | "on" |
iso.3.6.1.4.1.35265.1.127.1.9.1.7.0 | INTEGER | 2.4 GHz radio interface channel | "1" |
iso.3.6.1.4.1.35265.1.127.1.9.1.7.1 | INTEGER | 5 GHz radio interface channel | "48" |
iso.3.6.1.4.1.35265.1.127.1.9.1.8.0 | INTEGER | 2.4 GHz radio interface channel utilization (%) | "84" |
iso.3.6.1.4.1.35265.1.127.1.9.1.8.1 | INTEGER | 5 GHz radio interface channel utilization (%) | "30" |
Traps
OID | Messages within trap | Type | Description | Example |
---|---|---|---|---|
iso.3.6.1.4.1.35265.1.60.1.8.5.0.1 | OID | Trap OID on device reboot | ||
iso.3.6.1.4.1.35265.1.60.1.8.5.1.1.0 | OctetString | Text message about reboot reason | "Ap was rebooted by firmware switching" | |
iso.3.6.1.4.1.35265.1.60.1.8.5.1.2.0 | INTEGER | Message with code of the reboot reason |
Configuration
OID | Type | Name | Description | SET example | Possible values |
---|---|---|---|---|---|
Radio configuration | |||||
.1.3.6.1.4.1.35265.1.127.5.1.1.1.1.0 | STRING | radioCommonInterface.0 | 2.4 GHz radio interface name | The parameter is not available for editing, read only. | wlan0 |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.1.1 | STRING | radioCommonInterface.1 | 5 GHz radio interface name | The parameter is not available for editing, read only. | wlan1 |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.2.0 | STRING | radioWorkMode.0 | 802.11 mode 2.4 GHz | "bg", "bgn", "n" | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.2.1 | STRING | radioWorkMode.1 | 802.11 mode 5 GHz | "a", "an", "ac" | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.3.0 | INTEGER | radioTxPower.0 | 2.4 GHz transmit power, dBm | "11 - 16" | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.3.1 | INTEGER | radioTxPower.1 | 5 GHz transmit power, dBm | "11- 19" | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.38.0 | INTEGER | radioAutoChannel.0 | 2.4 GHz radio channel auto selection | "0" — disable When auto channel selection is enabled, operational channel is selected from a limited list of channels — radioLimitChannels.0 If use of limited list of channels radioUseLimitChannels.0 is disabled, operational channel will be selected from all channels of the 2.4 GHz range (from 1 to 13 channel) If auto selection is disabled, the access point will operate on the channel specified in the radioChannel.0 parameter | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.38.1 | INTEGER | radioAutoChannel.1 | 5 GHz radio channel auto selection | "0" — disable When auto channel selection is enabled, operational channel is selected from a limited list of channels — radioLimitChannels.1 If use of limited list of channels radioUseLimitChannels.0 is disabled, operational channel will be selected from all channels of the 5 GHz range (from 36 to 165 channel) If auto selection is disabled, the access point will operate on the channel specified in the radioChannel.1 parameter | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.39.0 | INTEGER | radioUseLimitChannels.0 | Using a limited channel list in 2.4 GHz auto channel selection | "0" — disable If this parameter is enabled, the auto selection process will utilize the limited list of channels described in the radioLimitChannels.0 parameter If disabled, the limited list of channels will be ignored, and a channel will be selected from the entire 2.4 GHz range (from channel 1 to 13) | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.39.1 | INTEGER | radioUseLimitChannels.1 | Using a limited channel list in 2.4 GHz auto channel selection | "0" — disable If this parameter is enabled, the auto selection process will utilize the limited list of channels described in the radioLimitChannels.1 parameter If disabled, the limited list of channels will be ignored, and a channel will be selected from the entire 5 GHz range (from channel 36 to 165) | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.40.0 | STRING | radioLimitChannels.0 | 2.4 GHz limited list of channels | The limited list of channels is specified by a line formatted as '1 6 11' Use of this list in auto select depends on radioUseLimitChannels.0 parameter state. | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.40.1 | STRING | radioLimitChannels.1 | 5 GHz limited list of channels | The limited list of channels is specified by a line formatted as '36 40 44 48' Use of this list in auto select depends on radioUseLimitChannels.1 parameter state. | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.5.0 | INTEGER | radioChannel.0 | 2.4 GHz radio channel number | At 20 MHz channel width: "1 - 13" At 40 MHz channel width: "1 - 9" — Lower | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.5.1 | INTEGER | radioChannel.1 | 5 GHz radio channel number | At 20 MHz channel width: "36 - 165" At 40 MHz Lower channel width: "36, 44, 52, 60, 132,140, 149, 157" At 40 MHz Upper channel width: "40, 48, 56, 64, 136,144, 153, 161" At 80 MHz channel width: "36 - 161" | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.6.0 | INTEGER | radioBandwidth.0 | 2.4 GHz radio channel width | "20", "40" If an error occurs when setting channel width to 40 MHz, check which channel is currently set on the access point. It is possible that this channel does not meet the condition specified in the radioControlSideBand.0 parameter.
| |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.6.1 | INTEGER | radioBandwidth.1 | 5 GHz radio channel width | "20", "40", "80" If an error occurs when setting channel width to 40 MHz, check which channel is currently set on the access point. It is possible that this channel does not meet the condition specified in the radioControlSideBand.1 parameter. In this case:
| |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.7.0 | STRING | radioControlSideBand.0 | Selection of the main 2.4 GHz channel (lower, upper) for 40 MHz band | "upper" — upper channel If an error occurs when changing the parameter value, it may mean that the current operational channel does not match the new value of this parameter. To change main channel:
| |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.7.1 | STRING | radioControlSideBand.1 | Selection of the main 5 GHz channel (lower, upper) for 40 MHz band | "upper" — upper channel If an error occurs when changing the parameter value, it may mean that the current operational channel does not match the new value of this parameter. To change main channel:
| |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.8.0 | INTEGER | radioEnableFixedRate.0 | Enabling fixed 2.4 GHz transmission rate | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.8.1 | INTEGER | radioEnableFixedRate.1 | Enabling fixed 5 GHz transmission rate | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.9.0 | STRING | radioFixedRate.1 | Fixed modulation for 2.4 GHz transmission | At 20 MHz channel width: DSSS1, DSSS2 At 40 MHz channel width: MCS0...MCS15 | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.9.1 | STRING | radioFixedRate.1 | Fixed modulation for 5 GHz transmission | At 20 MHz channel width: OFDM6, OFDM9, OFDM12, OFDM18, OFDM24, OFDM36, OFDM48, OFDM54 At 40 MHz channel width: MCS0...MCS15 At 80 MHz channel width: NSS1-MCS0...NSS1-MCS8 | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.10.0 | INTEGER | radioEnableMaximalRate.0 | Enabling restrictions for modulation for 2.4 GHz transmission | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.10.1 | INTEGER | radioEnableMaximalRate.1 | Enabling restrictions for modulation for 5 GHz transmission | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.26.0 | INTEGER | radioAckTimeout.0 | 2.4 GHz ACK timeout | [0; 255] | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.26.1 | INTEGER | radioAckTimeout.1 | 5 GHz ACK timeout | [0; 255] | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.27.0 | INTEGER | radioDisableAtf.0 | Disabling 2.4 GHz ATF | "0" — enable ATF "1" — disable ATF | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.27.1 | INTEGER | radioDisableAtf.1 | Disabling 5 GHz ATF | "0" — enable ATF "1" — disable ATF | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.28.0 | INTEGER | radioObssCoex.0 | Enabling 2.4 GHz OBSS | "0" — disable Only for 40 MHz | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.28.1 | INTEGER | radioObssCoex.1 | Enabling 5 GHz OBSS | "0" — disable Only for 40 and 80 MHz | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.29.1 | STRING | radioDfs.1 | Selecting 5 GHz DFS mode | "disabled" — mechanism is off, DFS channels are not available to select; "auto" — mechanism is enabled; "forced" — mechanism is enabled, DFS channels are available to select. | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.30.0 | INTEGER | radioSgi.0 | Enabling 2.4 GHz SGI | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.30.1 | INTEGER | radioSgi.1 | Enabling 5 GHz SGI | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.31.0 | INTEGER | radioStbc.0 | Enabling 2.4 GHz STBC | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.31.1 | INTEGER | radioStbc.1 | Enabling 5 GHz STBC | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.32.0 | INTEGER | radioBeaconInterval.0 | 2.4 GHz beacon interval | [20; 2000] | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.32.1 | INTEGER | radioBeaconInterval.1 | 5 GHz beacon interval | [20; 2000] | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.33.0 | INTEGER | radioFragThreshold.0 | 2.4 GHz fragmentation threshold | [256; 2346] | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.33.1 | INTEGER | radioFragThreshold.1 | 5 GHz fragmentation threshold | [256; 2346] | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.34.0 | INTEGER | radioRtsThreshold.0 | 2.4 GHz RTS threshold | [0; 65536] | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.34.1 | INTEGER | radioRtsThreshold.1 | 5 GHz RTS threshold | [0; 65536] | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.35.0 | INTEGER | radioAggregation.0 | 2.4 GHz frame aggregation | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.35.1 | INTEGER | radioAggregation.1 | 5 GHz frame aggregation | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.36.0 | INTEGER | radioShortPreamble.0 | 2.4 GHz short preamble | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.36.1 | INTEGER | radioShortPreamble.1 | 5 GHz short preamble | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.37.0 | INTEGER | radioTxBroadcastLimit.0 | 2.4 GHz Broadcast/Multicast traffic limiting | [0; 2000000000] | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.37.1 | INTEGER | radioTxBroadcastLimit.1 | 5 GHz Broadcast/Multicast traffic limiting | [0; 2000000000] | |
QoS configuration | |||||
.1.3.6.1.4.1.35265.1.127.5.1.2.1.1.0 | STRING | radioQosInterface.0 | Name of the interface on which QoS is configured at 2.4 GHz | The parameter is not available for editing, read only | wlan0 |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.1.1 | STRING | radioQosInterface.1 | Name of the interface on which QoS is configured at 5 GHz | The parameter is not available for editing, read only | wlan1 |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.2.0 | INTEGER | radioManualQoSEnable.0 | Enabling 2.4 GHz QoS (it is possible to override default EDCA parameters) | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.2.1 | INTEGER | radioManualQoSEnable.1 | Enabling 5 GHz QoS (it is possible to override default EDCA parameters) | "0" — disable "1" — enable | |
EDCA parameters of the base station | |||||
.1.3.6.1.4.1.35265.1.127.5.1.2.1.3.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.3.1 | INTEGER | radioApBkAifs.0 radioApBkAifs.1 | 2.4 and 5 GHz AIFS Background queue | [1; 255] | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.4.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.4.1 | INTEGER | radioApBkCwMin.0 radioApBkCwMin.1 | 2.4 and 5 GHz cwMin Background queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.5.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.5.1 | INTEGER | radioApBkCwMax.0 radioApBkCwMax.1 | 2.4 and 5 GHz cwMax for Background queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.6.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.6.1 | INTEGER | radioApBkTxOp.0 radioApBkTxOp.1 | 2.4 and 5 GHz TXOP Limit for Background queue | [0; 65535] | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.7.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.7.1 | INTEGER | radioApBeAifs.0 radioApBeAifs.1 | 2.4 and 5 GHz AIFS for Best Effort queue | [1; 255] | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.8.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.8.1 | INTEGER | radioApBeCwMin.0 radioApBeCwMin.1 | 2.4 and 5 GHz cwMin for Best Effort queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.9.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.9.1 | INTEGER | radioApBeCwMax.0 radioApBeCwMax.1 | 2.4 and 5 GHz cwMax for Best Effort queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.10.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.10.1 | INTEGER | radioApBeTxOp.0 radioApBeTxOp.1 | 2.4 and 5 GHz TXOP Limit for Best Effort queue | [0; 65535] | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.11.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.11.1 | INTEGER | radioApViAifs.0 radioApViAifs.1 | 2.4 and 5 GHz AIFS for Video queue | [1; 255] | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.12.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.12.1 | INTEGER | radioApViCwMin.0 radioApViCwMin.1 | 2.4 and 5 GHz cwMin for Video queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.13.0 | INTEGER | radioApViCwMax.0 | 2.4 and 5 GHz cwMax for Video queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.14.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.14.1 | INTEGER | radioApViTxOp.0 radioApViTxOp.1 | 2.4 and 5 GHz TXOP Limit for Video queue | [0; 65535] | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.15.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.15.1 | INTEGER | radioApVoAifs.0 | 2.4 and 5 GHz AIFS for Voice queue | [1; 255] | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.16.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.16.1 | INTEGER | radioApVoCwMin.0 radioApVoCwMin.1 | 2.4 and 5 GHz cwMin for Voice queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.17.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.17.1 | INTEGER | radioApVoCwMax.0 radioApVoCwMax.1 | 2.4 and 5 GHz cwMax for Voice queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.18.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.18.1 | INTEGER | radioApVoTxOp.0 radioApVoTxOp.1 | 2.4 and 5 GHz TXOP Limit for Voice queue | [0; 65535] | |
EDCA parameters for user station | |||||
.1.3.6.1.4.1.35265.1.127.5.1.2.1.19.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.19.1 | INTEGER | radioClientBkAifs.0 radioClientBkAifs.1 | 2.4 and 5 GHz AIFS for Background queue | [1; 255] | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.20.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.20.1 | INTEGER | radioClientBkCwMin.0 radioClientBkCwMin.1 | 2.4 and 5 GHz cwMin for Background queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.21.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.21.1 | INTEGER | radioClientBkCwMax.0 radioClientBkCwMax.1 | 2.4 and 5 GHz cwMax for Background queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.22.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.22.1 | INTEGER | radioClientBkTxOp.0 radioClientBkTxOp.1 | 2.4 and 5 GHz TXOP Limit for Background | [0; 65535] | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.23.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.23.1 | INTEGER | radioClientBeAifs.0 radioClientBeAifs.1 | 2.4 and 5 GHz AIFS for Best Effort queue | [1; 255] | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.24.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.24.1 | INTEGER | radioClientBeCwMin.0 radioClientBeCwMin.1 | 2.4 and 5 GHz cwMin for Best Effort | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.25.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.25.1 | INTEGER | radioClientBeCwMax.0 radioClientBeCwMax.1 | 2.4 and 5 GHz cwMax for Best Effort queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.26.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.26.1 | INTEGER | radioClientBeTxOp.0 radioClientBeTxOp.1 | 2.4 and 5 GHz TXOP Limit for Best Effort queue | [0; 65535] | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.27.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.27.1 | INTEGER | radioClientViAifs.0 radioClientViAifs.0 | 2.4 and 5 GHz AIFS for Video queue | [1; 255] | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.28.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.28.1 | INTEGER | radioClientViCwMin.0 radioClientViCwMin.1 | 2.4 and 5 GHz cwMin for Video queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.29.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.29.1 | INTEGER | radioClientViCwMax.0 radioClientViCwMax.1 | 2.4 and 5 GHz cwMax for Video queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.30.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.30.1 | INTEGER | radioClientViTxOp.0 radioClientViTxOp.1 | 2.4 and 5 GHz TXOP Limit for Video queue | [0; 65535] | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.31.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.31.1 | INTEGER | radioClientVoAifs.0 radioClientVoAifs.1 | 2.4 and 5 GHz AIFS for Voice queue | [1; 255] | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.32.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.32.1 | INTEGER | radioClientVoCwMin.0 radioClientVoCwMin.1 | 2.4 and 5 GHz cwMin for Voice queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.33.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.33.1 | INTEGER | radioClientVoCwMax.0 radioClientVoCwMax.1 | 2.4 and 5 GHz cwMax for Voice queue | "1, 3, 7, 15, 31, 63, 127, 255, 511, 1023" | |
.1.3.6.1.4.1.35265.1.127.5.1.2.1.34.0 .1.3.6.1.4.1.35265.1.127.5.1.2.1.34.1 | INTEGER | radioClientVoTxOp.0 radioClientVoTxOp.1 | 2.4 and 5 GHz TXOP Limit for Voice queue | [0; 65535] | |
VAP configuration | |||||
.1.3.6.1.4.1.35265.1.127.5.2.1.1.1(.0-7) | OctetString | vapInterface | List of interfaces allowed for editing (read only) | The parameter is not available for editing, read only. | [ "wlanX-va0" - "wlanX-va3" ] |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.2(.0-7) | INTEGER | vapEnable | Enable VAP | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.3(.0-7) | INTEGER | vapVlanTrunk | Enable Vlan Trunk | "0" — disable | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.4(.0-7) | INTEGER | vapVlanId | VLAN number to untag when transmitting Wi-Fi traffic to clients | [1; 4094 ] "0" — disabling VLAN ID on VAP | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.5(.0-7) | INTEGER | vapGeneralVlanMode | Enabling General Mode | "0" — disable | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.6(.0-7) | INTEGER | vapGeneralVlanId | VLAN number to untag when transmitting Wi-Fi traffic to clients | [1; 4094 ] "0" — disabling General VLAN ID on VAP | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.7(.0-7) | OctetString | vapVlanPriority | 802.1p priority | "auto", [ 0; 7 ] | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.8(.0-7) | INTEGER | vapStaLimit | Limiting number of clients on VAP | [0; 64] "0" — no limit on the number of clients connected to the VAP | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.9(.0-7) | INTEGER | vapInactivityTimeout | Client disconnect timeout due to inactivity | [0; 2000000] | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.10(.0-7) | OctetString | vapSsid | SSID name | String, maximum length — 32 characters. Example: "WOP-2L" | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.11(.0-7) | OctetString | vapSecurityMode | Security mode | "off","WPA","WPA2","WPA_WPA2", | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.12(.0-7) | OctetString | vapKeyWep | WEP key | String length from 5 to 13 characters | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.13(.0-7) | OctetString | vapKeyWpa | WPA key | String length from 8 to 63 characters | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.14(.0-7) | INTEGER | vapStationIsolation | Client isolation on VAP | "0" — disable | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.15(.0-7) | INTEGER | vapPriorityByDscp | Selecting traffic prioritization method: via DSCP or 802.1p | "1" — DSCP "0" — 802.1p | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.18(.0-7) | OctetString | vapShaperVapTxMode | Configuring shaper in direction from access point to clients (in total), connected to this VAP | "off" — shaper is disabled; "kbps" — configuring shaping, kbps; "pps" — configuring shaping, pps. | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.19(.0-7) | INTEGER | vapShaperVapTxValue | Shaper value | [ 0; 2000000000] | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.20(.0-7) | OctetString | vapShaperVapRxMode | Configuring shaper in direction from clients (in total) connected to this VAP to the access point | "off" — shaper is disabled; "kbps" — configuring shaping, kbps; "pps" — configuring shaping, pps. | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.21(.0-7) | INTEGER | vapShaperVapRxValue | Shaper value | [ 0; 2000000000] | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.22(.0-7) | OctetString | vapShaperStaTxMode | Configuring shaper in direction from access point to clients (separately) connected to this VAP | "off" — shaper is disabled; "kbps" — configuring shaping, kbps; "pps" — configuring shaping, pps. | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.23(.0-7) | INTEGER | vapShaperStaTxValue | Shaper value | [ 0; 2000000000] | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.24(.0-7) | OctetString | vapShaperStaRxMode | Configuring shaper in direction from clients (separately) connected to this VAP to the access point | "off" — shaper is disabled; "kbps" — configuring shaping, kbps; "pps" — configuring shaping, pps. | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.25(.0-7) | INTEGER | vapShaperStaRxValue | Shaper value | [ 0; 2000000000] | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.26(.0-7) | INTEGER | vapRadiusAuthPort | Radius server port used for authentication and authorization | [0; 65535] | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.27(.0-7) | OctetString | vapRadiusAuthAddress | Radius server address used for authentication and authorization | Radius server IP address | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.28(.0-7) | OctetString | vapRadiusAuthPassword | Radius server password used for authentication and authorization | String from 1 to 64 characters | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.29(.0-7) | INTEGER | vapRadiusTlsEnable | Enabling TLS | "0" — disable | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.30(.0-7) | INTEGER | vapRadiusAcctEnable | Enabling Radius Accounting sending | "0" — disable | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.31(.0-7) | INTEGER | vapRadiusAcctPort | Radius server port used for Accounting reception | [0; 65535] | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.32(.0-7) | OctetString | vapRadiusAcctAddress | Radius server address used for Accounting reception | Radius server IP address | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.33(.0-7) | OctetString | vapRadiusAcctPassword | Radius server password used for Accounting reception | String from 1 to 64 characters | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.34(.0-7) | INTEGER | vapRadiusAcctPeriodic | Periodic Accounting sending | "0" — disable | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.35(.0-7) | INTEGER | vapRadiusAcctInterval | Accounting sending interval | [0; 86400] | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.36(.0-7) | OctetString | vapRadiusDomain | Domain | String from 1 to 253 characters | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.37(.0-7) | INTEGER | vapRadiusDebug | Enabling Radius debugging | "0" — disable | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.38(.0-7) | OctetString | vapRadiusLogfile | Location and name of the file used for Radius logging | " /var/log/radius-wlan0-va1.log" | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.39(.0-7) | INTEGER | vapRadiusLogfileLimit | Size of the file used for Radius logging, in bytes | [0; 30000] | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.40(.0-7) | INTEGER | vapPortalEnable | Enabling portal authorization | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.2.1.1.41(.0-7) | STRING | vapVirtualPortalName | String | ||
.1.3.6.1.4.1.35265.1.127.5.2.1.1.42(.0-7) | STRING | vapRedirectUrl | Address for redirecting | String of the following type: 'http://<IP>:<PORT>/eltex_portal/' | |
WDS configuration | |||||
.1.3.6.1.4.1.35265.1.127.5.1.1.1.17.0 | INTEGER | radioConfigWdsEnable.0 | Enabling 2.4 GHz WDS | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.17.1 | INTEGER | radioConfigWdsEnable.1 | Enabling 5 GHz WDS | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.18.0 | STRING | radioConfigWdsSecurityMode.0 | 2.4 GHz encryption mode | 'off' | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.18.1 | STRING | radioConfigWdsSecurityMode.1 | 5 GHz encryption mode | 'off' 'WPA2' 'WPA' | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.19.0 | STRING | radioConfigWdsKeyWep.0 | WEP 2.4 GHz key | 5 or 13 characters | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.19.1 | STRING | radioConfigWdsKeyWep.1 | WEP 5 GHz key | 5 or 13 characters | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.20.0 | STRING | radioConfigWdsKeyWpa.0 | 2.4 GHz WPA key | String from 8 to 63 characters | |
.1.3.6.1.4.1.35265.1.127.5.1.1.1.20.1 | STRING | radioConfigWdsKeyWpa.1 | 5 GHz WPA key | String from 8 to 63 characters | |
WDS links configuration | |||||
WDS links table .1.3.6.1.4.1.35265.1.127.5.3 | |||||
.1.3.6.1.4.1.35265.1.127.5.3.1.1.2(.0-7) | INTEGER | wdsLinkEnable | Enabling WDS link | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.3.1.3(.0-7) | INTEGER | wdsMtu | MTU for link | [1; 2490] | |
.1.3.6.1.4.1.35265.1.127.5.3.1.4(.0-7) | STRING | wdsMac | Remote MAC address | MAC address of the remote device Entry format:
| |
.1.3.6.1.4.1.35265.1.127.5.3.1.5(.0-7) | STRING | wdsTxRate | Static TX modulation | 'auto' OFDM[6,9,12,18,24,36,48,54] MCS[0...15] NSS[1,2]-MCS[0...9] - 5 ГГц | |
SNMP configuration | |||||
.1.3.6.1.4.1.35265.1.127.5.11.1.0 | INTEGER | snmpEnable | Enabling use of SNMP | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.11.2.0 | OctetString | snmpRoCommunity | Password for parameters reading | ||
.1.3.6.1.4.1.35265.1.127.5.11.3.0 | OctetString | snmpRwCommunity | Password for parameters writing | ||
.1.3.6.1.4.1.35265.1.127.5.11.4.0 | OctetString | snmpTrapSink | IP address or domain name of the SNMPv1-trap messages receiver | IP address in xx.xx.xx.xx format | |
.1.3.6.1.4.1.35265.1.127.5.11.5.0 | OctetString | snmpTrap2Sink | IP address or domain name of the SNMPv2-trap messages receiver | IP address in xx.xx.xx.xx format | |
.1.3.6.1.4.1.35265.1.127.5.11.6.0 | OctetString | snmpInformSink | IP address or domain name of the Inform messages receiver | IP address in xx.xx.xx.xx format | |
.1.3.6.1.4.1.35265.1.127.5.11.7.0 | OctetString | snmpSysname | Device name | ||
.1.3.6.1.4.1.35265.1.127.5.11.8.0 | OctetString | snmpContact | Device manufacturer contact information | ||
.1.3.6.1.4.1.35265.1.127.5.11.9.0 | OctetString | snmpLocation | Device location information | ||
.1.3.6.1.4.1.35265.1.127.5.11.10.0 | OctetString | snmpTrapCommunity | Password in traps | ||
.1.3.6.1.4.1.35265.1.127.5.11.11.0 | INTEGER | snmpDebug | Enabling SNMP logging | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.11.12.0 | OctetString | snmpLogfile | Path to SNMP logs | Path in /dir/subdir/filename | |
.1.3.6.1.4.1.35265.1.127.5.11.13.0 | INTEGER | snmpLogfileLimit | Log file size | [0; 30000] | |
Syslog agent configuration | |||||
.1.3.6.1.4.1.35265.1.127.5.14.1.0 | INTEGER | syslogEnable | Enabling Syslog agent | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.14.2.0 | OctetString | syslogMode | Syslog agent operation mode | 'File' — Syslog writing to a local file on the device. 'ServerAndFile' — Syslog writing to a local file on the device and Syslog sending to a remote Syslog server. | |
.1.3.6.1.4.1.35265.1.127.5.14.3.0 | INTEGER | syslogFileSize | Syslog file size | [1; 1000] | |
.1.3.6.1.4.1.35265.1.127.5.14.4.0 | INTEGER | syslogPort | Port for incoming Syslog server messages | [1; 65535] By default 514, required for "Server and file" mode | |
.1.3.6.1.4.1.35265.1.127.5.14.5.0 | OctetString | syslogServer | Syslog server IP address | IP address in xx.xx.xx.xx format
| |
Access options configuration | |||||
.1.3.6.1.4.1.35265.1.127.5.6.1.0 | OctetString | adminPassword | Access password to the device | ||
Netconf configuration | |||||
.1.3.6.1.4.1.35265.1.127.5.8.1.0 | INTEGER | netconfEnable | Enabling Netconf on the device | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.8.2.0 | INTEGER | netconfDebug | Enabling Netconf logging | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.8.3.0 | OctetString | netconfLogfile | Path to Netconf log file | Path in /dir/subdir/filename format | |
.1.3.6.1.4.1.35265.1.127.5.8.4.0 | INTEGER | netconfLogfileLimit | Netconf log file size | [0; 30000] | |
Date and time configuration | |||||
.1.3.6.1.4.1.35265.1.127.5.7.1.0 | OctetString | dateTimeMode | Configuring date and time (auto/manually) | 'ntp' — setting time via NTP time synchronization protocol 'manual' — manual time configuration on the device | |
.1.3.6.1.4.1.35265.1.127.5.7.2.0 | OctetString | timeZone | Time zone | 'Europe/Moscow (Moscow,Russia)' 'Europe/Helsinki (Helsinki,Finland)' 'Asia/Novosibirsk (Novosibirsk)' etc. | |
.1.3.6.1.4.1.35265.1.127.5.7.3.0 | INTEGER | dstEnable | Enabling daylight saving time | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.7.4.0 | OctetString | dstStart | Starting daylight saving time | String of a format: numeral — first, second, third, fourth, last | |
.1.3.6.1.4.1.35265.1.127.5.7.5.0 | OctetString | dstEnd | Ending daylight saving time | String of a format: numeral — first, second, third, fourth, last | |
.1.3.6.1.4.1.35265.1.127.5.7.6.0 | INTEGER | dstOffset | Time offset in minutes | [0; 720] | |
.1.3.6.1.4.1.35265.1.127.5.7.7.0 | OctetString | manualSystemTime | System date and time (manual) | String of a format: "year-month-day hours:minutes:seconds" | |
.1.3.6.1.4.1.35265.1.127.5.7.8.0 | OctetString | ntpServer | Internal clock synchronization server | IP address or domain name of the NTP server | |
Telnet configuration | |||||
.1.3.6.1.4.1.35265.1.127.5.5.1.0 | INTEGER | telnetEnable | Enabling access to the device via Telnet protocol | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.5.2.0 | INTEGER | telnetPort | Assigning Telnet port | [0; 65535] | |
SSH configuration | |||||
.1.3.6.1.4.1.35265.1.127.5.4.1.0 | INTEGER | sshEnable | Enabling access to the device via SSH protocol | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.4.2.0 | INTEGER | sshPort | Assigning SSH port | [0; 65535] | |
System parameters configuration | |||||
.1.3.6.1.4.1.35265.1.127.5.12.1.0 | INTEGER | systemGlobalStationIsolation | Global isolation | "0" — disable "1" — enable | |
.1.3.6.1.4.1.35265.1.127.5.12.2.0 | OctetString | systemHostname | Device name | ||
.1.3.6.1.4.1.35265.1.127.5.12.3.0 | OctetString | systemApLocation | Node domain (AP Location) of the EMS management system device tree, where access point is located | ||
Automatic log files download configuration | |||||
.1.3.6.1.4.1.35265.1.127.5.15.1.0 | INTEGER | autologPeriod | Period of automatic downloading of log files from the /var/log/ directory in seconds | [0; 86400] "0" — automatic log files download is enabled | |
.1.3.6.1.4.1.35265.1.127.5.15.2.0 | OctetString | autologServerAddress | IP address of the server to which log files should be downloaded from the device | IP address in xx.xx.xx.xx format | |
.1.3.6.1.4.1.35265.1.127.5.15.3.0 | INTEGER | autologFileSize | Maximum size of log file in KB | [0; 20000] | |
.1.3.6.1.4.1.35265.1.127.5.15.4.0 | OctetString | autologProtocol | Download protocol | "tftp" | |
.1.3.6.1.4.1.35265.1.127.5.15.5.0 | INTEGER | autologRetryCount | Number of retries to automatically send log files in case of failure | [0; 5] | |
APB configuration | |||||
.1.3.6.1.4.1.35265.1.127.5.16.2.0 | STRING | captivePortalApIpAlias | Portal address that is displayed in user's browser | It is not recommended to change this value. | |
.1.3.6.1.4.1.35265.1.127.5.16.3.0 | INTEGER | captivePortalApbEnable | Enabling APB service | "1" — enable "0" — disable | |
.1.3.6.1.4.1.35265.1.127.5.16.4.0 | STRING | captivePortalApbUrl | APB service address | String of a format: 'ws://<IP address of the APB server>:8090/apb/broadcast' |
Management
OID | Type | Description | Example of use |
---|---|---|---|
.1.3.6.1.4.1.35265.1.127.3.1.0 | INTEGER | Device reboot | |
.1.3.6.1.4.1.35265.1.127.3.3.0 | STRING | Start and device configuration update | |
.1.3.6.1.4.1.35265.1.127.3.4.0 | INTEGER | Saving current configuration to the non-volatile memory of the device |