interface
The command allows you to switch to the management mode of one or group of interfaces.
Syntax
interface gpon-port <RANGE>
Parameters
<RANGE> – interface number. The range of values and numbering rules are described in Table 4.1. If you specify the value 'all' in the command, all interfaces of the given type will be specified.
You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - ).
Command mode
CONFIG
Example
ma4000(config)# interface gpon-port 2/2 ma4000(config)(if-gpon-2/2)#
shutdown
The command disables an interface being configured.
The use of a negative form (no) of the command enables the interface being configured.
Syntax
[no] shutdown
Parameters
The command contains no arguments.
Command mode
GPON-PORT
Example
ma4000(if-gpon-1)# shutdown
Configured interface is disabled.
fec
This command allows to enable downstream error correction on the GPON interface.
The use of the negative form of the command (no) disables this function.
Syntax
[no] fec
Parameters
The command contains no arguments.
Command mode
GPON-PORT
Example
ma4000(config)(if-gpon-1)# fec
optics
This command is used to configure the optical parameters of the GPON interface.
Syntax
optics <PARAM> <VALUE>
Parameters
<PARAM> – optical parameter name;
<VALUE> – parameter value.
Command mode
GPON-PORT
Example
ma4000(config)(if-gpon-1)# optics reset data burst bcdr d1 23
profile
This command assigns a certain VLAN or ADDRESS-TABLE profile to a given interface/group of interfaces.
Syntax
profile <PROFILE> <NAME>
Parameters
<PROFILE> – profile type:
- vlan – VLAN profile;
- address-table – address-table profile.
<NAME> – profile name, case sensitive.
Command mode
GPON-PORT
Example
ma4000(config)(if-gpon-1)# profile address-table TEST
show interface gpon-port <SLOT>/<CHANNEL> state
This command is used to view the state of the GPON interface.
Syntax
show interface gpon-port <SLOT>/<CHANNEL> state
Parameters
<SLOT> – PLC8 module number, may take values [0..15]. If the value 'all' is specified, all modules will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - );
<CHANNEL> – PLC8 module channel number, may take values [0..7]. If the value «all» is specified, all channels of this module will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - ).
Command mode
ROOT
Example
ma4000# # show interface gpon-port 13/all state
Reading:
Channels status information:
Channel:
State:
ONT count:
SFP vendor:
SFP product number:
SFP vendor revision:
SFP temperature [C]:
SFP voltage [V]:
SFP tx bias current [mA]:
SFP tx power [dBm]:
show interface gpon-port <SLOT>/<CHANNEL> redundancy
Syntax
show interface gpon-port <SLOT>/<CHANNEL> redundancy
Parameters
<SLOT> – PLC8 module number, may take values [0..15]. If the value 'all' is specified, all modules will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - );
<CHANNEL> – PLC8 module channel number, may take values [0..7]. If the value 'all' is specified, all channels of this module will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - ).
Command mode
ROOT
Example
ma4000# show interface gpon-port 13/all redundancy
Channel:
Redundancy mode:
Channel state:
show interface gpon-port <SLOT>/<CHANNEL> igmp groups
This command is used to view IGMP groups that are assigned to this PLC8 channel.
Syntax
show interface gpon-port<SLOT>/<CHANNEL>igmp groups
Parameters
<SLOT> – PLC8 module number, may take values [0..15]. If the value 'all' is specified, all modules will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - );
<CHANNEL> – PLC8 module channel number, may take values [0..7]. If the value 'all' is specified, all channels of this module will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - ).
Command mode
ROOT
Example
ma4000# show interface gpon-port 13/all igmp groups
All IGMP groups (0):
<no groups>
show interface gpon-port <SLOT>/<CHANNEL> configuration
This command is used to view the PLC8 channel configuration.
Syntax
show interface gpon-port<SLOT>/<CHANNEL>configuration
Parameters
<SLOT> – PLC8 module number, may take values [0..15]. If the value 'all' is specified, all modules will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - );
<CHANNEL> – PLC8 module channel number, may take values [0..7]. If the value 'all' is specified, all channels of this module will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - ).
Command mode
ROOT
Example
ma4000# show interface gpon-port 6/0 configuration
-----------------------------------
Slot 6 GPON-port 0 configuration
-----------------------------------
Status: UP
Fec down: false
Profile vlan: vlan-00 OLT Profile Vlan 0
Profile address table: addresstable-00 OLT Profile Address Table 0
Use custom optics settings: false
show interface gpon-port <SLOT>/<CHANNEL> counters v-interface
This command is used to view the v-interface counters (between the switch and the PLC8 module olt chips).
Syntax
show interface gpon-port <SLOT>/<CHANNEL> counters v-interface
Parameters
<SLOT> – PLC8 module number, may take values [0..15]. If the value 'all' is specified, all modules will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - );
<CHANNEL> – PLC8 module channel number, may take values [0..7]. If the value 'all' is specified, all channels of this module will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - ).
Command mode
ROOT
Example
ma4000# show interface gpon-port 13/all counters v-interface
## Downstream counters for channels:
1 RX Alignment errors
2 RX Pause frames
3 RX CRC-32 errors
4 RX Oversize errors
5 RX Bad FCS
6 RX Too long frames
7 RX Undersize errors
8 RX Range errors
9 RX Ok frames
10 RX total frames
11 RX 64 octets frames
12 RX 65-127 octets frames
13 RX 128-255 octets frames
14 RX 256-511 octets frames
15 RX 512-1023 octets frames
16 RX 1024-1518 octets frames
17 RX 1519-MAX octets frames
18 RX Total unicast packets
19 RX Total multicast packets
20 RX Total broadcast packets
22 RX Total octets
24 RX Ok octets
25 RX FIFO overflow errors
26 RX Bad FCS and <64 octets
27 RX Frame errors
## Upstream counters for channels:
1 TX frames without errors
2 TX valid pause frames
3 TX frames with errors
4 TX good unicast packets
5 TX good multicast packets
6 TX good broadcast packets
8 TX octets
clear counters interface gpon-port
This command is used to clear the counters on a given GPON interface(s) from the ONT or OLT side.
Syntax
clear counters interface gpon-port <SLOT>/<CHANNEL> <SIDE>
Parameters
<SLOT> – PLC8 module number, may take values [0..15]. If the value 'all' is specified, all modules will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - );
<CHANNEL> – PLC8 module channel number, may take values [0..7]. If the value 'all' is specified, all channels of this module will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - );
<SIDE> – the side from which the counters will be reset: OLT or ONT.
Command mode
ROOT
Example
ma4000# clear counters interface gpon-port all/all ont-side
show interface gpon-port <SLOT>/<CHANNEL> downstream-ber
This command is used to view downstream counters on the specified channel of the PLC8 module.
Syntax
show interface gpon-port <SLOT>/<CHANNEL> downstream-ber
Parameters
<SLOT> – PLC8 module number, may take values [0..15]. If the value 'all' is specified, all modules will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - );
<CHANNEL> – PLC8 module channel number, may take values [0..7]. If the value 'all' is specified, all channels of this module will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - ).
Command mode
ROOT
Example
ma4000# show interface gpon-port 6/0 downstream-ber
-----------------------------------
Slot 6 GPON-port 0 BER table
-----------------------------------
## Ch/ Id Errors Intervals BER Interval BER
1 0/ 0 0 0 0 0
2 0/ 1 0 0 0 0
3 0/ 3 0 0 0 0
4 0/ 4 0 0 0 0
5 0/ 5 0 0 0 0
6 0/ 6 0 0 0 0
7 0/ 7 0 0 0 0
8 0/ 8 0 0 0 0
9 0/ 9 0 0 0 0
10 0/ 10 0 0 0 0
11 0/ 11 0 0 0 0
12 0/ 12 0 0 0 0
13 0/ 13 0 0 0 0
14 0/ 14 0 0 0 0
15 0/ 15 0 0 0 0
16 0/ 16 0 0 0 0
17 0/ 17 0 0 0 0
18 0/ 18 0 0 0 0
19 0/ 19 0 0 0 0
20 0/ 20 0 0 0 0
21 0/ 21 0 0 0 0
22 0/ 22 0 0 0 0
23 0/ 23 0 0 0 0
24 0/ 24 0 0 0 0
25 0/ 25 0 0 0 0
26 0/ 26 0 0 100000 0
27 0/ 27 0 0 100000 0
28 0/ 29 0 0 100000 0
29 0/ 30 0 0 100000 0
30 0/ 31 0 0 100000 0
show interface gpon-port <SLOT>/<CHANNEL> optics state
This command is used to view the optical parameters of the PLC8 module channel.
Syntax
show interface gpon-port <SLOT>/<CHANNEL> optics state
Parameters
<SLOT> – PLC8 module number, may take values [0..15]. If the value 'all' is specified, all modules will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - );
<CHANNEL> – PLC8 module channel number, may take values [0..7]. If the value 'all' is specified, all channels of this module will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - ).
Command mode
ROOT
Example
ma4000# show interface gpon-port 13/all optics state
Reading:
Channels status information:
Channel:
State:
ONT count:
SFP vendor:
SFP product number:
SFP vendor revision:
SFP temperature [C]:
SFP voltage [V]:
SFP tx bias current [mA]:
SFP tx power [dBm]:
show interface gpon-port <SLOT>/<CHANNEL> optics configuration
This command is used to view the configuration of optical parameters of the PLC8 module channel.
Syntax
show interface gpon-port <SLOT>/<CHANNEL> optics configuration
Parameters
<SLOT> – PLC8 module number, may take values [0..15]. If the value 'all' is specified, all modules will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - );
<CHANNEL> – PLC8 module channel number, may take values [0..7]. If the value 'all' is specified, all channels of this module will be specified in the command. You may specify the list of numbers using comma ( , ) or specify the range using hyphen ( - ).
Command mode
ROOT
Example
ma4000# show interface gpon-port 6/0 optics configuration
-----------------------------------
Slot 6 GPON-port 0 optics configuration
-----------------------------------
Laser reset enable: enabled
Laser reset polarity: low
Laser sd polarity: low
Sd source: laser sd
Sd hold normal: disabled
Sd hold snr ranging: disabled
Reset type snr ranging: delay based
Reset type normal: start burst based
Reset data burst bcdr d1: 11
Reset data burst bcdr d2: 1
Reset data burst laser d1: 5
Reset data burst laser d2: 2
Reset snr burst bcdr d1: 9
Reset snr burst bcdr d2: 2
Reset snr burst laser d1: 1
Reset snr burst laser d2: 2
Reset rng burst bcdr d1: 9
Reset rng burst bcdr d2: 2
Reset rng burst laser d1: 1
Reset rng burst laser d2: 2
Reset single bcdr d1: 1
Reset single bcdr d2: 1
Reset single laser d1: 1
Reset single laser d2: 1
Reset double bcdr d4: 1
Reset double bcdr d3: 1
Reset double laser d4: 1
Reset double laser d3: 1
Delay snr timer: 8
Delay snr preamble: 32
Delay snr delimiter: 128
Delay snr burst: 128
Delay rng timer: 8
Delay rng preamble: 32
Delay rng delimiter: 128
Delay rng burst: 0
Delay single burst: 1
Delay double burst: 1
Preamble correlation preamble length: 8
Preamble length snr rng: 119
Preamble guard time data mode: 32
Preamble type1 size data: 0
Preamble type2 size data: 0
Preamble type3 size data: 5
Preamble type3 pattern: 170
Preamble delimiter size: 20
Preamble delimiter byte1: 171
Preamble delimiter byte2: 89
Preamble delimiter byte3: 131
Voltage if mode: lvpecl
Rssi trigger pulse width: 3000