gpon olt authentication
The command sets the ONT authentication mode: by password, by serial number, by a combination of serial number and password. The use of a negative form (no) of the command sets the default value.
Syntax
gpon olt authentication <VALUE>
no gpon olt authentication
Parameters
<VALUE> – ONT authentication mode:
- password – by password;
- serial – by serial number;
- both – by combination of serial number and password.
Default value:
both – ONT authentication by combination of serial number and password
Command mode
CONFIG
Example
ma4000(config)# gpon olt authentication password
gpon olt block-duplicated-mac
This command enables protection against duplicate MAC addresses (MAC spoofing).
The use of the negative form (no) disables ONT blocking when duplicated MAC addresses are detected.
Syntax
[no] gpon olt block-duplicated-mac
Parameters
The command contains no arguments.
Default value:
disable – blocking disabled
Command mode
CONFIG
Example
ma4000(config)# gpon olt block-duplicated-mac
gpon olt broadcast-gem-port
The command sets the GEM port number for broadcast traffic.
The use of a negative form (no) of the command sets the default value.
Syntax
gpon olt broadcast-gem-port <PORT>
no gpon olt broadcast-gem-port
Parameters
<PORT> – number of GEM port for broadcast traffic, may take values [0..4095].
Default value
4095
Command mode
CONFIG
Example
ma4000(config)#gpon olt broadcast-gem-port 4095
gpon olt dba-reduced-latency
The command enable the mode to lower DBA latency.
The use of a negative form (no) of the command sets the default value.
Syntax
[no] gpon olt dba-reduced-latency enable
Parameters
The command contains no arguments.
Command mode
CONFIG
Example
ma4000(config)# gpon olt dba-reduced-latency enable
gpon olt dhcpra-shaper
This command sets the maximum number of DHCP messages per second (for each ONT)
The use of a negative form (no) of the command sets the default value.
Syntax
gpon olt dhcpra-shaper <VALUE>
no gpon olt dhcpra-shaper
Parameters
<VALUE> – maximum number of DHCP messages per second for ONT.
Default value:
100
Command mode
CONFIG
Example
ma4000(config)# gpon olt dhcpra-shaper 33
gpon olt encryption
The command enables GPON traffic encryption.
The use of the negative form (no) of the command disables GPON traffic encryption.
Syntax
[no] gpon olt encryption
Parameters
The command contains no arguments.
Command mode
CONFIG
Example
ma4000(config)# gpon olt encryption
gpon olt encryption key-update
The command is used to set an encryption key change period.
The use of a negative form (no) of the command sets the default parameter value.
Syntax
gpon olt encryption key-update <TIME>
no gpon olt encryption key-update
Parameters
<TIME> – encryption key update period, may take values [0..65535], in minutes.
Default value:
1 minute
Command mode
CONFIG
Example
ma4000(config)# gpon olt encryption key-update 33333
gpon olt model
The command sets the datapath construction model – the order of forming rules for traffic transfer.
The use of a negative form (no) of the command sets the default parameter value.
Syntax
gpon olt model <VALUE>
no gpon olt model
Parameters
<VALUE> – datapath construction model:
- transmission of Broadcast and unicast packets in one GEM port, VLAN operation (U-VID assignment) is performed on OLT side;
- transmission of Broadcast traffic in dedicated GEM port, VLAN operation (U-VID assignment) is performed on OLT side;
- transmission of Broadcast traffic in dedicated GEM port, VLAN operation (U-VID assignment) is performed on ONT side.
Default value
model1
Command mode
CONFIG
Example
ma4000(config)# gpon olt model 1
gpon olt multicast-gem-port
The command sets the GEM port number for multicast traffic.
The use of a negative form (no) of the command sets the default parameter value.
Syntax
gpon olt multicast-gem-port <PORT>
no gpon olt multicast-gem-port
Parameters
<PORT> – number of GEM port for multicast traffic, may take values [0..4095].
Default value
4094
Command mode
CONFIG
Example
ma4000(config)# gpon olt multicast-gem-port 32
gpon olt ont-block-time
This command sets the time to lock the port when duplicate MAC addresses are detected.
The use of a negative form (no) of the command sets the default value.
Syntax
gpon olt ont-block-time <TIME>
no gpon olt ont-block-time
Parameters
<TIME> – blocking time, may take values in the range [1..2147483647] minutes.
Default value
5 minutes
Command mode
CONFIG
Example
ma4000(config)#gpon olt ont-block-time 10
gpon olt ont-sn-format
This command sets the format of displaying the ONT serial number.
The use of a negative form (no) of the command sets the default value.
Syntax
gpon olt ont-sn-format <VALUE>
no gpon olt ont-sn-format
Parameters
<VALUE> – display format:
- literal – AAAAXXXXXXXX, where A is uppercase letter, and X in HEX format [0-F];
- numerical – XXXXXXXXXXXXXXXX, where X in HEX format [0-F];
- section-numerical – XX-XX-XX-XX-XX-XX-XX-XX, where X in HEX format [0-F].
Default value
literal
Command mode
CONFIG
Example
ma4000(config)#gpon olt ont-sn-format literal
show gpon olt
The command to view the settings of GPON-configuration of PLC8 modules:
- Block duplicated mac – protection against duplicate MAC addresses;
- Ont block time – port blocking time in minutes when detecting duplicate MAC addresses;
- Dhcpra shaper – maximum number of DHCP messages per second for each ONT;
- Datapath – datapath configuration:
- Model – datapath construction model;
- Broadcast gem port – number of GEM port for broadcast traffic;
- Multicast gem port –number of GEM port for multicast traffic;
- Encryption – GPON traffic encryption settings
- Enable – GPON traffec incryption state: enabled, disabled;
- Key update interval – encryption key update period, in minutes;
- ONT authentication mode – ONT authentication mode;
- Auto reconfigure ont – ONT auto reconfiguration state: enabled, disabled;
- Auto reconfigure channel – channel auto reconfiguration state: enabled, disabled;
- Auto reconfigure olt – OLT auto reconfiguration state: enabled, disabled;
- Ont sn format – ONT serial number display format.
Syntax
show gpon olt
Parameters
Command contains no arguments.
Command mode
ROOT
Example
ma4000(config)# showgponolt
Block duplicated mac: disabled
Ont block time: 5
Dhcpra shaper: 100
Datapath:
Model: model1
Broadcast gem port: 4095
Multicast gem port: 4094
Encryption:
Enable: false
Key update interval: 1
ONT authentication mode: both
Auto reconfigure ont: true
Auto reconfigure channel: true
Auto reconfigure olt: true
Ont sn format: literal